Dylan Laduranty
88bb019438
boards/sam0: update to use generic uart_hw_fc module
2020-03-10 14:22:34 +01:00
Marian Buschsieweke
f2edcf9674
makefiles/tools/avrdude: Improved debug handling
...
- Choose correct debug protocol for ATmega328P (which supports debugWIRE instead
of JTAG)
- Allow overwriting debugger device via AVR_DEBUGDEVICE environment variable,
default to the Atmel-ICE (least expensive, supports most AVR devices)
2020-03-10 14:03:33 +01:00
Marian Buschsieweke
edd93411fe
dist: De-duplicated AVR debug config & scripts
...
Use common debug.sh, debug_srv.sh and gdb.conf for all AVR boards.
2020-03-10 12:54:51 +01:00
631fbd9fc8
boards/blxxxpill: rework programmer specific configuration
2020-03-10 11:42:10 +01:00
f56470925b
boards: include common dfu logic where applicable
2020-03-10 11:42:10 +01:00
Francisco
1b5f22ec2e
Merge pull request #8410 from OTAkeys/pr/fix_stm32f1_boards
...
boards: fix CLOCK_PLL_PREDIV on stm32f1-based boards
2020-03-10 09:35:48 +01:00
benpicco
f0ac1624c5
Merge pull request #13594 from aabadie/pr/tools/cc2538-bsl_rework
...
tools/cc2538-bsl: deduplicate buildsystem integration
2020-03-09 19:39:43 +01:00
benpicco
0cf6e39be5
Merge pull request #13589 from maribu/stm32f103-jtag-pins
...
cpu/stm32f103: Allow boards to expose JTAG pins as GPIOs
2020-03-09 19:07:52 +01:00
b4418426ba
boards/cc2538: use common cc2538-bsl handling file
2020-03-09 18:26:08 +01:00
Vincent Dupont
4647659ea8
boards: fix CLOCK_PLL_PREDIV on stm32f1xx boards
2020-03-09 18:00:48 +01:00
Leandro Lanzieri
ab10b33848
boards/esp32-wroom-32/doc: Add SPI freq configuration for mrf24j40
2020-03-09 16:51:35 +01:00
Leandro Lanzieri
cffc9b70bf
boards/esp32-wroom-32: Remove drivers configuration from Makefile.dep
...
This removes the configuration parameters for mrf24j40 and enc28j60
drivers, which were present in the boards's Makefile.dep. There is
already documentation regarding how to correctly configure these devices
for the board.
2020-03-09 16:49:11 +01:00
2ec09ebd74
boards/nrf52: remove useless export of FLASH_TARGET_TYPE
2020-03-08 15:12:44 +01:00
Marian Buschsieweke
8fd8c8273f
boards/{nucleo-f103rb,b*pill}: Expose JTAG pins as GPIOs
...
The Nucleo-F103RB comes with an internal SWD programmer/debugger. Thus, the JTAG
pins are not going to be used for debugging / programming anyway. The pins are
exposed on the headers, so allowing them to be used as GPIOs make a lot of
sense.
The Bluepill / Blackpill boards only expose the SWD pins on the debug header,
but the JTAG pins (not also used by SWD) are exposed on the GPIO pin headers.
Hence, exposing them as regular GPIOs seems to be a reasonable choice.
2020-03-08 13:06:34 +01:00
3e97c01c33
thingy52: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:42 +01:00
74022a4bb8
ruuvitag: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:42 +01:00
0573db8a85
reel: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:42 +01:00
bef16095df
pinetime: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:42 +01:00
cbd3c1c643
particle-*: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:42 +01:00
822590ad56
nrf52840-mdk: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:41 +01:00
87b2aa5ed9
nrf52832-mdk: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:41 +01:00
71589a11ec
nrf51dk: Enable the nRF51 built-in DC/DC converter
2020-03-07 17:37:41 +01:00
bea3f71f91
nrf52xxxdk: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:41 +01:00
ec2a3d33c8
acd52832: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:41 +01:00
benpicco
7396d05605
Merge pull request #13575 from fjmolinas/pr_cc2538_rf_deps
...
cpu/cc2538: handle cc2538_rf deps in Makefile.dep
2020-03-06 18:00:51 +01:00
Francisco Molina
80ecac5fde
boards: use cc2538_rf as netdev_default for CPU=cc2538
2020-03-06 14:17:52 +01:00
Francisco Molina
ff6f6618fb
cpu/cc2538: handle cc2538_rf deps in Makefile.dep
2020-03-06 14:17:19 +01:00
Benjamin Valentin
ed4d871835
dist/tools/cc2538-bsl: use upstream version
...
Automatically fetch the upstream version of cc2538-bsl.py instead
of maintaining our own fork of the tool.
fixes #13566
2020-03-06 11:13:21 +01:00
ed316309c8
Merge pull request #11874 from kaspar030/ztimer
...
sys/ztimer: initial import
2020-03-06 09:46:27 +01:00
benpicco
681678e3f3
Merge pull request #13537 from jue89/feature/sam0-spi-frequency
...
cpu/sam0_common: mitigate rounding errors of SPI baud rate calculation
2020-03-04 16:50:46 +01:00
f49e756436
boards/ek-lm4f120xl: add ztimer config, increase ztimer_usec_min
2020-03-04 12:44:03 +01:00
a2c0823063
boards/native: add ztimer configuration
2020-03-04 12:44:03 +01:00
84365e326a
boards/*-kw41z: add ztimer_msec config
2020-03-04 12:44:03 +01:00
73adecc02d
boards/samr21-xpro: add ztimer config
2020-03-04 12:44:03 +01:00
eafba65911
boards/common/arduino-atmega: add ztimer configuration
2020-03-04 12:44:03 +01:00
Koos
24b9b99fee
boards/stm32f3discovery: Updated broken image link
2020-03-04 09:54:36 +01:00
Koos
f970f67785
boards/sodaq-sara-aff: Updated broken image link
2020-03-04 09:54:36 +01:00
Koos
ed2ea24405
boards/sodaq-autonomo: Updated broken image link
2020-03-04 09:54:36 +01:00
Koos
2a253ed175
boards/saml11-xpro: Updated broken image link
2020-03-04 09:54:36 +01:00
Koos
8219685be1
boards/nrf52840-mdk: Updated broken image link
2020-03-04 09:54:36 +01:00
Koos
6dd8b2deac
boards/frdm-k64f: Updated broken image link
2020-03-04 09:54:36 +01:00
Koos
cec9817b2e
boards/arduino-mega2560: Updated broken image link
2020-03-04 09:54:36 +01:00
benpicco
7792f91ddc
Merge pull request #13535 from btcven/2020_03_02-cc1312-openocd
...
boards/cc1312-launchpad: add OpenOCD configuration
2020-03-04 00:26:14 +01:00
Jean Pierre Dudey
6e77d9194b
boards/cc1352-launchpad: enable OpenOCD
...
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-03-03 13:42:33 -05:00
Jean Pierre Dudey
ca2e2a4289
boards/cc1312-launchpad: add OpenOCD configuration
...
This enables OpenOCD for the CC1312 LaunchPad.
All we need is:
- The Texas Instruments version of OpenOCD
(https://git.ti.com/cgit/sdo-emu/openocd )
- Set the `PROGRAMMER` environment variable to `openocd`.
- Connect a cc1312-launchpad and play with the commands.
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-03-03 13:42:29 -05:00
Martine Lenders
e4f27b415e
Merge pull request #13394 from benpicco/atmega-rtc
...
cpu/atmega_common: implement emulated RTC support
2020-03-03 19:03:47 +01:00
95d607b54d
Merge pull request #13480 from aabadie/pr/tools/openocd_export_variables
...
tools/openocd: export configuration variables only to required targets
2020-03-03 18:16:05 +01:00
Benjamin Valentin
1dd260b446
boards: enable RTC for every ATmega board that supports RTT
...
Every ATmega board that can run an Real Time Timer can also run
an emulated Real Time Clock.
Got all supported boards by adding `FEATURES_REQUIRED += arch_8bit`
to `tests/periph_rtt` and running
sed -i 's/FEATURES_PROVIDED += periph_rtt/
FEATURES_PROVIDED += periph_rtc\n
FEATURES_PROVIDED += periph_rtt/g'
on them.
2020-03-03 16:27:44 +01:00
26222d601c
boards/arduino-mkr: don't export MKR_JLINK_DEVICE variables
2020-03-03 14:18:03 +01:00
d10211b7ff
boards/esp32-wroom-32: don't export _PARAM_DEFINED variables
2020-03-03 14:18:03 +01:00
a8b81adbd2
boards/cc2650*: don't export XDEBUGGER variable
2020-03-03 14:18:03 +01:00
21f48af3cd
boards/nz32-sc151: don't export ID variable
2020-03-03 14:18:03 +01:00
2722869dbb
boards/arduino-due: don't export BOSSA_ARDUINO_PREFLASH
2020-03-03 14:18:03 +01:00
acce5e22d1
boards/pic32: don't export APPDEPS
...
This variable is already export in vars.inc.mk
2020-03-03 14:18:03 +01:00
cc48b67fb5
boards/pic32: don't export USE_UHI_SYSCALLS
2020-03-03 14:18:03 +01:00
b7f5b18991
boards: don't export ROM_OFFSET variable
2020-03-03 14:18:03 +01:00
bd81060354
boards/{telosb,iotlab}: remove useless export for BAUD
...
The variable is already eported in serial.inc.mk
2020-03-03 14:18:03 +01:00
Francisco
3f062a78b2
Merge pull request #13045 from aabadie/pr/boards/remote_factorize
...
boards/remote*: cleanup and factorize code in peripheral configuration headers
2020-03-03 13:21:04 +01:00
481f3bcb35
Merge pull request #13180 from fjmolinas/pr_slwstk6000b_cleanup
...
boards/slwstk6000b-*: cleanup
2020-03-03 13:15:03 +01:00
Juergen Fitschen
8fbfb13c84
Revert "boards/samr30-xpro: fix AT86RF212B communication"
...
This reverts commit a9faac7218
2020-03-03 12:32:54 +01:00
d13d1aed48
Merge pull request #13336 from bergzand/pr/mtd_spi_nor/erase_timings_in_struct
...
mtd_spi_nor: erase timings in struct
2020-03-03 11:59:28 +01:00
f1ba22534a
boards: don't export globally OPENOCD_RESET_USE...
2020-03-03 11:42:19 +01:00
Francisco Molina
86ed76fec0
boards/common/slwstk6000b: remove unused files
2020-03-03 11:24:28 +01:00
Francisco Molina
e951b720b8
boards/common/slwstk6000b: use slwstk6000b.vars.mk to parse JLINK_DEVICE
2020-03-03 11:24:27 +01:00
Francisco Molina
22aae93efb
boards/common/slwstk6000b: cleanup slwrb41* includes
2020-03-03 11:24:26 +01:00
Francisco Molina
b7783e67a8
boards/common/slwstk6000b: use slwstk6000b.vars.mk to parse CPU_MODEL
2020-03-03 11:24:26 +01:00
Francisco Molina
96cfa1d41c
boards/common/slwstk6000b: add module variables makefile
2020-03-03 11:22:48 +01:00
8931889865
pinetime: add erase timings to mtd_spi_nor instance
2020-03-03 09:49:08 +01:00
dcdaf8a2ab
mulle: add erase timings to mtd_spi_nor instance
2020-03-03 09:49:08 +01:00
Juergen Fitschen
a9faac7218
boards/samr30-xpro: fix AT86RF212B communication
...
This board is driven by a 16MHz clock source. In this case, the baud rate generator is able to clock the SPI interface with 4MHz or 8MHz only.
Due to integer division and rounding, the interface is actually driven with 8MHz, which is too fast for the AT86RF212.
2020-03-02 18:38:04 +01:00
Francisco
5af4c5a9c5
Merge pull request #13470 from kfessel/fix13179
...
boards/nucleo-f767zi: Fix13179 make nucleo-f767zi debuggable again
2020-02-28 17:42:10 +01:00
benpicco
2ebf1d68b4
Merge pull request #13497 from benpicco/openmote-b-fixes
...
boards/openmote-b: add saul config, add note about flashing
2020-02-28 14:59:25 +01:00
Karl Fessel
979b4d5cf7
Revert "boards/nucleo-f767zi: add correct flash bank openocd config"
...
This reverts commits:
- 1dec5ba61b53f60db66f
2020-02-28 13:51:58 +01:00
Benjamin Valentin
961b333ea6
boards/openmote-b: add saul config
...
Hook up the GPIOs and the si7006 sensor to SAUL.
2020-02-28 13:37:15 +01:00
Benjamin Valentin
bf96e97e34
boards/openmote-b: extend doc.txt about flashing
...
To flash the board the intelhex python package needs to be installed.
Add a note about it to the documentation.
2020-02-28 13:37:15 +01:00
benpicco
23c5d34284
Merge pull request #10846 from benemorius/kw41z-mini
...
boards: add support for kw41z-mini
2020-02-28 07:40:25 +01:00
Thomas Stilwell
ef6024cf1a
boards: add kw41z-mini
2020-02-27 21:34:04 -06:00
Benjamin Valentin
9d1a2b5fb4
boards/mcb2388: add I2C config
...
The pins for I2C0 and I2C1 are available on the board,
nothing is wired up to them.
2020-02-26 23:41:38 +01:00
Benjamin Valentin
4d5d3eb9e6
boards/msba2: hook up i2c
...
I2C is not used by any chip on the board, but I2C2 is availiable
on the JP3 connector (shared with UART2).
- SDA: P0.10
- SCL: P0.11
2020-02-26 23:41:38 +01:00
cbb248319e
boards/pinetime: update mtd_spi_nor config
2020-02-26 10:00:55 +01:00
2dcf65d942
Merge pull request #13332 from bergzand/pr/mtd_spi_nor/params_struct
...
mtd_spi_nor: Move const params to separate struct
2020-02-26 09:43:18 +01:00
Peter Kietzmann
a27b58fbba
Merge pull request #13479 from MichelRottleuthner/pr_phytec_fix_tmp_addr
...
boards/pba-d-01-kw2x: add config for tmp006 addr
2020-02-25 21:04:20 +01:00
a8231f2079
Merge pull request #13161 from bergzand/pr/pinetime/mtd
...
pinetime: add MTD configuration
2020-02-25 20:44:59 +01:00
Michel Rottleuthner
9ec1a6fab5
boards/pba-d-01-kw2x: add config for tmp006 addr
2020-02-25 20:25:26 +01:00
benpicco
aa1c23d4bd
Merge pull request #11929 from fabian18/driver-at24cxxx-eeprom
...
Driver for AT24CXXX EEPROM
2020-02-25 18:16:45 +01:00
0d468c1068
boards/common/silabs: remove OPENOCD_CONFIG export
2020-02-25 17:26:00 +01:00
f451eb692c
Merge pull request #13452 from aabadie/pr/tools/openocd_config_export
...
tools/openocd: only export OPENOCD_CONFIG to required targets
2020-02-25 15:11:38 +01:00
514873fe12
pinetime: add MTD configuration
2020-02-25 14:31:39 +01:00
785052e410
Merge pull request #13468 from aabadie/pr/tools/bossa_rework
...
tools/bossa: split between 1.8 and 1.9 versions
2020-02-25 13:32:38 +01:00
d41621e95f
boards/arduino-due: force bossa 1.8 version
2020-02-25 11:49:10 +01:00
fe8c242a30
boards/native: remove exports of UNDEF vars
2020-02-25 09:40:34 +01:00
benpicco
77d6eaaf19
Merge pull request #13461 from benpicco/sam_xpro-led-fix
...
boards/samXXX-xpro: clear LED on init
2020-02-24 21:56:36 +01:00
Benjamin Valentin
bc5ac92cff
boards/samXXX-xpro: clear LED on init
...
The LED on the sam-xpro boards is active low, so we have
to turn it off manually, otherwise it's always on.
2020-02-24 19:44:36 +01:00
benpicco
4671fd2fe4
Merge pull request #10475 from chrysn-pull-requests/openocd-for-stk3700
...
boards/any silabs: Allow selecting OpenOCD
2020-02-24 19:12:43 +01:00
fabian18
07f7d818bd
boards/same54-xpro: use at24cxxx EEPROM
2020-02-24 14:00:25 +01:00
9363f077d6
boards: don't export globally OPENOCD_CONFIG
...
The variable is already exported to required target in openocd.inc.mk
2020-02-24 10:04:11 +01:00
bd081cd980
tools/openocd: remove default OPENOCD_CONFIG value
...
The default value is already set in openocd.inc.mk
2020-02-24 10:04:11 +01:00
d7cbfe4f45
Merge pull request #13378 from francois-berder/nucleo-doc-cleanup
...
boards: nucleo*: Cleanup documentation
2020-02-24 08:01:42 +01:00
Jean Pierre Dudey
130467dd91
cc1312-launchpad: add board documentation
...
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-02-22 12:43:11 -05:00
benpicco
ce947b4824
Merge pull request #12955 from gschorcht/cpu/esp/deduplicate_and_cleanup
...
cpu/esp*: code deduplication and cleanup
2020-02-22 13:03:18 +01:00
benpicco
261ede7b79
Merge pull request #13414 from benpicco/boards/same54-xpro/peripheral-clocks
...
boards/same54-xpro: don't source peripheral clocks from main clock
2020-02-21 23:25:22 +01:00
benpicco
8d77ec55ae
Merge pull request #13409 from aabadie/pr/cpu/nrf_gpio_t
...
cpu/nrf5x: provide gpio_t type definition
2020-02-21 18:55:46 +01:00
Martine Lenders
4be4f5ad0a
boards/native: add deprecation warnings for make all-debug
2020-02-21 12:51:41 +01:00
Martine Lenders
1786a8353a
boards/native: remove now unnecessary -g3 CFLAGS
...
dbd865413c
2020-02-21 12:50:02 +01:00
benpicco
ea24d30e7a
Merge pull request #13417 from gschorcht/boards/esp32/doc_remove_mcu_table
...
boards/esp32: remove MCU feature table in board documentation
2020-02-21 10:13:44 +01:00
Gunar Schorcht
d251ffd205
boards/esp8266: enable arduino feature
2020-02-21 09:09:34 +01:00
Gunar Schorcht
51200364da
boards/esp8266: fix ARDUINO_LED definitions
...
ARDUINO_LED specifies the according Arduino pin to which the LED is connected and not the GPIO.
2020-02-21 09:09:34 +01:00
Cenk Gündoğan
86fcc35994
Merge pull request #13423 from kaspar030/turn_on_native_debug
...
native: turn on creation of debug symbols (CFLAGS += -g)
2020-02-20 18:20:11 +01:00
dbd865413c
native: turn on creation of debug symbols (CFLAGS += -g)
2020-02-20 17:06:56 +01:00
e324b22c96
Merge pull request #13418 from gschorcht/boards/esp32/fix_btn0_pin
...
boards/esp32: rename BUTTON0_PIN to BTN0_PIN
2020-02-20 14:40:39 +01:00
Gunar Schorcht
6a7ba7ba1a
boards/esp32: rename BUTTON0_PIN to BTN0_PIN
...
Since a number of applications rely on the existence of the BTN0_PIN definition, the BUTTON0_PIN definition has been renamed to BTN0_PIN to make the ESP32 boards compatible with these applications. However, for compatibility with earlier versions, BUTTON0_PIN is still defined as an alias of BTN0_PIN.
2020-02-20 12:14:44 +01:00
Gunar Schorcht
e4b3ce7c91
boards/esp32: remove MCU feature table in doc
...
Instead of using the same MCU feature table in every board documentation, it refers to the MCU documentation. This makes it easier to maintain the MCU feature table.
2020-02-20 08:47:18 +01:00
6182e7c977
boards/nrf52: remove uint8_t cast for GPIO_UNDEF
2020-02-19 19:16:58 +01:00
Benjamin Valentin
3ee7b72431
boards/same54-xpro: don't source peripheral clocks from main clock
...
Use the dedicated 48 MHz clock as a source for the peripheral clocks.
This was already done for I2C to allow it to work despite the 120 MHz
main clock.
Not running the peripherals off the main clock will allow for dynamic
re-clocking of the main clock in the future, without affecting the
operation of the peripherals.
It also gives more flexibility to the main clock selection in general.
2020-02-19 17:52:12 +01:00
Sebastian Meiling
85c01f2ebd
boards: update supported features of pba-d-01-kw2x
2020-02-18 11:42:05 +01:00
Sebastian Meiling
867090c579
boards: update links in doc of pba-d-01-kw2x
2020-02-18 11:40:34 +01:00
Sebastian Meiling
a9cb3b637f
boards: add pinout ref for pba-d-01-kw2x
2020-02-18 11:40:34 +01:00
Yegor Yefremov
5cd205dffd
boards/esp32-ttgo-t-beam: correct SX127x chip frequencies
...
According to the datasheet, SX1278 covers frequencies till 525MHz
and hence, cannot be used for the 868/915 MHz band. So swap both
chips.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2020-02-17 10:15:40 +01:00
chrysn
f4b1d60887
boards/*silabs: Move programmer selection to common
...
This removes duplication for the jlink case (keeping only any
non-default values in the board makefiles), and opens up STK3700's
OpenOCD programmability for generic boards.
2020-02-14 09:42:20 +01:00
chrysn
80167b8ba4
boards/stk3700: Use OpenOCD-shipped board file
2020-02-14 09:29:32 +01:00
chrysn
4387739494
boards/stk3700: Allow selecting OpenOCD
...
OpenOCD works well with those devices; the OpenOCD config is provided at
the default location and only needs to refer to the setup that OpenOCD
ships.
2020-02-14 08:56:27 +01:00
Francois Berder
99142b170c
boards: nucleo-l152re: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:43:20 +00:00
Francois Berder
7222f42c86
boards: nucleo-f446ze: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:42:49 +00:00
Francois Berder
343f39174e
boards: nucleo-f446re: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:42:20 +00:00
Francois Berder
a42b5d79ab
boards: nucleo-f411re: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:41:13 +00:00
Francois Berder
8f766d594e
boards: nucleo-f410rb: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:40:48 +00:00
Francois Berder
5b81034fa1
boards: nucleo-f401re: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:39:39 +00:00
Francois Berder
1b27d5cb9a
boards: nucleo-f334r8: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:39:11 +00:00
Francois Berder
6fb2275452
boards: nucleo-f303ze: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:38:40 +00:00
Francois Berder
a8cec40371
boards: nucleo-f303re: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:38:15 +00:00
Francois Berder
3739d81aad
boards: nucleo-f303k8: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:37:32 +00:00
Francois Berder
b475598cb8
boards: nucleo-f302r8: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:36:34 +00:00
Francois Berder
d28fb30797
boards: nucleo-f207zg: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:35:54 +00:00
Francois Berder
2cb858c72b
boards: nucleo-f103rb: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:35:21 +00:00
Francois Berder
3e22a77bf0
boards: nucleo-f091rc: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:34:45 +00:00
Francois Berder
7145e56e74
boards: nucleo-f072rb: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:34:03 +00:00
Francois Berder
7c9bbf5d9b
boards: nucleo-f070rb: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:33:46 +00:00
Francois Berder
43a475fef8
boards: nucleo-f030r8: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:32:50 +00:00
Benjamin Valentin
02e1c0a4ed
boards/same54-xpro: add configuration for AT24MAC402
2020-02-13 15:58:43 +01:00
Benjamin Valentin
59ca6a9b37
boards/avr-rss2: add configuration for AT24MAC602
2020-02-13 15:58:43 +01:00
Bas Stottelaar
3141e91380
Merge pull request #13174 from fjmolinas/pr_efm32_cleanup
...
cpu/efm32: cleanup
2020-02-12 22:42:10 +01:00
Dylan Laduranty
a2d63070ae
Merge pull request #13347 from francois-berder/boards-fpu
...
boards: Fix presence of FPU
2020-02-12 09:12:57 +01:00
Bas Stottelaar
d6b478f607
boards/efm32: provide CPU_FAM
2020-02-11 22:46:17 +01:00
3ac25c3ac9
Merge pull request #12556 from bergzand/wip/stusbdev
...
stm32_common: Add USB OTG FS/HS usbdev peripheral driver
2020-02-11 20:39:46 +01:00
Francois Berder
c76f0e1489
boards: Fix presence of FPU
...
Cortex-M0, Cortex-M0+ and Cortex-M3 MCU never have a FPU.
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-11 18:30:29 +00:00
d40ccc2d6f
mulle: Adapt to separate mtd_spi_nor params
2020-02-11 15:55:41 +01:00
1f5340c307
boards/stm32: Add default config for USB OTG HS peripheral
2020-02-11 15:50:22 +01:00
7f1325e48c
pyboard: add usbdev feature
2020-02-11 15:50:22 +01:00
08c74db3d9
stm32f769i-disco: add usbdev feature
2020-02-11 15:50:21 +01:00
033cb5559a
stm32f723e-disco: add usbdev feature
2020-02-11 15:50:21 +01:00
d9837182a0
stm32f4discovery: add usbdev feature
2020-02-11 15:50:21 +01:00
4d0f3d0d3a
stm32f429i-disc1: add usbdev feature
2020-02-11 15:50:20 +01:00
8198c52d17
nucleo-f767zi: add usbdev feature
2020-02-11 15:50:20 +01:00
befac12f9a
nucleo-f746zg: add usbdev feature
2020-02-11 15:50:20 +01:00
dca64d4120
nucleo-f722ze: add usbdev feature
2020-02-11 15:50:20 +01:00
0f885b3789
nucleo-f446ze: add usbdev feature
2020-02-11 15:50:19 +01:00
625698a1d2
nucleo-f429zi: add usbdev feature
2020-02-11 15:50:19 +01:00
2c6f0537df
nucleo-f413zh: add usbdev feature
2020-02-11 15:50:19 +01:00
f37b5d7ec7
nucleo-f412zg: add usbdev feature
2020-02-11 15:50:18 +01:00
3280248e89
nucleo-f207zg: add usbdev feature
2020-02-11 15:50:18 +01:00
fc63fb77bf
boards/stm32: Add default config for USB OTG FS peripheral
2020-02-11 15:50:18 +01:00
benpicco
33291ad675
Merge pull request #13306 from fjmolinas/pr_samr21_use_xosc
...
boards/sam[r/d]21-xpro: prefer XOSC32K for RTC/RTT (GCLK2)
2020-02-11 15:18:36 +01:00
benpicco
d8c050943c
Merge pull request #13327 from maribu/atmega-bootloader
...
boards: Cleaned up bootloader selection for ATmega
2020-02-10 23:18:43 +01:00
benpicco
82134ad77a
Merge pull request #13323 from francois-berder/mbedlpc1768-doc
...
boards: mbed_lpc1768: Improve documentation
2020-02-10 23:07:27 +01:00
Marian Buschsieweke
fec0f8dd48
boards/waspmote-pro: Refactor avrdude conf
2020-02-10 21:48:03 +01:00
Marian Buschsieweke
21b37a3f5e
boards/mega-xplained: Refactor avrdude conf
2020-02-10 21:48:03 +01:00
Marian Buschsieweke
ff53159f0e
boards/atmega256rfr2-xpro: Refactor avrdude conf
...
- No longer include `tools/serial.mk` and `tools/avrdude.mk`, as this is
no done by `boards/common/atmega`
- No longer provide `RESET ?=`, as this is now done in `tools/avrdude.mk` for
all ATmega boards unless they are using a bootloader
2020-02-10 21:48:03 +01:00
Marian Buschsieweke
26b4da2db2
boards/avr-rss2: Refactor avrdude conf
2020-02-10 21:48:03 +01:00
Marian Buschsieweke
e042bb43e1
boards/derfmega*: Refactor avrdude conf
2020-02-10 21:48:03 +01:00
Francois Berder
056c1e568c
boards: mbed_lpc1768: Improve documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-10 19:29:55 +00:00
benpicco
b44cf48a87
Merge pull request #13246 from benpicco/lpc23xx-spi
...
cpu/lpc2387: make SPI configurable
2020-02-10 17:01:41 +01:00
Marian Buschsieweke
f5d9f29b57
boards/arduino-leonardo: Refactor avrdude conf
2020-02-10 15:01:27 +01:00
Marian Buschsieweke
7f4782e3e6
boards/arduino-duemilanove: Refactor avrdude conf
2020-02-10 15:01:06 +01:00
Marian Buschsieweke
c1c25b0644
boards/arduino-nano: Refactor avrdude conf
...
- Use the common logic to translate from a bootloader to concrete flasher flags
- Extended documentation on how to use optiboot as alternative bootloader, as
the stock bootloader is affected by a bug preventing the use of RIOT's
pm_reboot() implementation
2020-02-10 14:59:24 +01:00
Marian Buschsieweke
88b90ee4af
boards/arduino-uno: Refactor avrdude conf
2020-02-10 14:59:06 +01:00
Marian Buschsieweke
23531b3a73
boards/arduino-mega2560: Refactor avrdude conf
2020-02-10 14:58:18 +01:00
Marian Buschsieweke
750d3078e4
boards/common/arduino-atmega: Refactoring
...
- including `avrdude.mk` and `serial.mk` is no longer needed
- the avrdude flag -F is dropped
- This allows flashing a board having an MCU different to the one
RIOT was compiled for
- It is better to let the user provide this flag manually if she/he really
wants to turn safety off, knows what she/he is doing, and accepts the
risk associated with this
- the avrdude flag -D is dropped
- This disables issuing an erase command during flashing, however this
erase cycle is strictly required to be able to program the flash
- This is only needed in case of the stk500v2 bootloader, which implicitly
does the erase cycle and fails if explicitly asked to do so
- Only for the stk500v2 bootloader this flag is now added
2020-02-10 14:52:07 +01:00
Marian Buschsieweke
95704348ae
boards/common/atmega: Refactor flash & serial conf
...
- Include `tools/avrdude.mk` and `tools/serial.mk` at the common place instead
for each ATmega based board individually
- Introduce the makefile variable BOOTLOADER to de-duplicate flash configs:
- Two boards using the same bootloader now just use `BOOTLOADER ?= foo`
and share the individual config
- These settings are not applied when `PROGRAMMER` is set to still allow
users to manually specify how to program their board
2020-02-10 14:48:39 +01:00
Benjamin Valentin
d675eb7cbb
boards/mcb2388: update SPI configuration
2020-02-10 13:41:00 +01:00
Benjamin Valentin
4342d81220
boards/mcb2388: add ADC configuration
...
The MCB2388 has a potentiometer connected to an ADC input.
2020-02-10 13:25:26 +01:00
Benjamin Valentin
9c0dfaada9
boards/msba2: add ADC configuration
...
ADC pins are on the AD/DA pins (JP8).
Configure AD0.0 - AD0.2 as laid out on the board schematics.
2020-02-10 13:25:26 +01:00
Francois Berder
b4ab22673e
boards: Use ARRAY_SIZE for setting UART_NUMOF, SPI_NUMOF, I2C_NUMOF
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-09 20:55:46 +00:00
Francisco Molina
c9ff150571
boards/sam%21-xpro: prefer XOSC32K for RTC/RTT (GCLK2)
2020-02-07 15:48:15 +01:00
713fead00a
boards: move some USEMODULE to Makefile.dep
2020-02-07 13:21:22 +01:00
benpicco
66c7c63c94
Merge pull request #13061 from gschorcht/cpu/esp32/rtc_xtal_32k
...
cpu/esp32: allow external 32 kHz crystal for the RTC hardware timer
2020-02-07 10:24:22 +01:00
Gunar Schorcht
1e71606305
boards/esp32: enable 32 kHz XTAL for WROVER-KIT
2020-02-07 00:46:16 +01:00
benpicco
3d95521c14
Merge pull request #13301 from gschorcht/board/esp32/fix_compile_error_c_linkage
...
boards/esp32: fix compilation error due to C linkage in examples/posix_sockets
2020-02-05 22:08:14 +01:00
Gunar Schorcht
cfcea03a58
board/esp32: fix compilation error due to C linkage
...
Including `board_common.h` header has to be outside the `extern C` linkage block.
2020-02-05 20:42:22 +01:00
d6264f56c8
Merge pull request #13168 from fjmolinas/pr_iotlab_openocd
...
boards/iotlab: add DEBUG_ADAPTER_ID openocd
2020-02-05 11:30:11 +01:00
Benjamin Valentin
c4e0ed4b79
boards: use explicit GCLK_SRC defines
2020-02-04 21:17:00 +01:00
Benjamin Valentin
4fbca251bc
boards/same54-xpro: use 48 MHz GCLK6 for I2C
...
We can't run I2C off the 120 MHz main clock as the availiable dividers are too small.
Use the 48 MHz GCLK 6 instead which offers an appropriate frequency.
fixes #12037
2020-02-04 21:16:54 +01:00
Benjamin Valentin
1496149bba
cpu/sam0: don't hard-code peripheral clocks
...
Instead of hard-coding the peripheral clocks to CLOCK_CORECLOCK
introduce helper functions to return the frequency of the individual
GCLKs and use those for baud-rate calculations.
This requires the GCLK to be part of the peripheral's config struct.
While this is already the case for most peripherals, this also adds
it for those where it wasn't used before.
As it defaults to 0 (CLOCK_CORECLOCK) no change is to be expected.
2020-02-04 21:06:21 +01:00
Benjamin Valentin
a51d167a43
cpu/sam0: use GCLK ID instead of bitmask
...
To simplify board definitions and for unification between samd2x and
newer models, don't use the GCLK bitmask in board definitions.
Instead use the GCLK index and generate the bitmask when needed.
2020-02-04 21:06:21 +01:00
Jean Pierre Dudey
8c68796ff8
boards/cc1312-launchpad: correct config. for gdb_agent_server
...
This enables the usage of `monitor reset` command in gdb.
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-02-04 07:13:20 -05:00
benpicco
cc90a896c7
Merge pull request #13166 from jeandudey/2020_01_19-cc26x2-cc13x2
...
cpu/cc13x2: rename cpu to cc26x2_cc13x2.
2020-02-04 11:45:59 +01:00
benpicco
5d1bf26f0c
Merge pull request #13076 from gschorcht/boards/esp32/ttgo_t_beam_gps
...
boards/esp32: enable GPS module on ESP32 TTGO T-Beam V1.0
2020-02-01 23:25:55 +01:00
Gunar Schorcht
c30674d539
boards/esp32-ttgo-t-beam: switch on GPS module
2020-02-01 16:12:05 +01:00
Gunar Schorcht
624c6f24ca
boards/esp32: allow board specific initialization
2020-02-01 16:12:05 +01:00
32f4986757
boards/hifive1*: remove useless stdio_uart include
...
stdio_uart is already pulled by default by the dependency resolution
mechanism.
2020-01-31 14:30:32 +01:00
Marian Buschsieweke
613ef0fdf0
boards/common/nucleo: Marked board_init as weak
...
Made `void board_init(void)` in the common implementation a weak symbol to
allow providing a custom board init, if the common nucleo board init misses
features.
2020-01-31 13:41:50 +01:00
Benjamin Valentin
985d340621
boards/avsextrem: update SPI config
2020-01-31 12:01:09 +01:00
Benjamin Valentin
3ae7bb425b
boards/msba2: update SPI configuration
2020-01-31 12:01:09 +01:00
Dylan Laduranty
d929087e57
Merge pull request #13233 from benpicco/edbg-update
...
tools/edbg: update to latest upstream version
2020-01-31 11:04:23 +01:00
benpicco
cdb427b760
Merge pull request #12475 from francois-berder/wifire-gpio-refactor
...
cpu: mips_pic32_common: Refactor GPIO peripheral
2020-01-31 09:46:57 +01:00
Benjamin Valentin
bd19a55804
boards: remove EDBG_DEVICE_TYPE
...
EDBG_DEVICE_TYPE is a property of the CPU, is should not be set
by every board individually.
2020-01-31 09:35:27 +01:00
Sören Tempel
8485c535d5
waspmote-pro: don't build the boards_common_atmega module
...
Only include its headers. Without this change board_init would be
defined twice. Once in `boards/waspmote-pro/board.c` and the other time
`boards/common/atmega/board.c`.
2020-01-29 12:32:16 +01:00
Francisco Molina
94853d5e1d
boards/iotlab-%: define DEBUG_ADAPTER
2020-01-28 11:56:56 +01:00
Francisco Molina
f79397f7be
boards/iotlab-%: use common openocd config
2020-01-28 11:56:38 +01:00
98995f685b
Merge pull request #13179 from fjmolinas/pr_openocd_stm32f7_probe
...
boards/nucleo-f767zi: add correct flash bank openocd config
2020-01-28 10:48:23 +01:00
Francisco Molina
1dec5ba61b
boards/common/stm32f7: add correct flash bank configuration
...
openocd configuration file for `stm32f7` relies on probing to find out
FLASH_ADDR. On nucleo-f767zi board probing (`flash probe 0`) fails when
`srst` is asserted, but `srst` needs to be asserted to be able to flash
the `BOARD` when sleeping or after a hardfault.
To circumvent this in boards/common/stm32/dist/stm32f7.cfg we define a new
flash bank with the appropriate fash start address and specify that this is
the flash bank to be used as default configuration instead of the
default by setting FLASH_BANK=4
2020-01-27 22:32:06 +01:00
Frits Kuipers
9206b955eb
boards/pinetime: Add pyocd support to pinetime board
2020-01-27 19:43:48 +01:00
benpicco
f6d750afe9
Merge pull request #13201 from gschorcht/boards/nucleo-f4xx-doc-fix
...
boards: doc fix for several nucleo-f4xxxx boards
2020-01-25 15:19:55 +01:00
Gunar Schorcht
6fc82f2b2a
boards: doc fix for several nucleo-f4xxxx boards
...
Rows in markdown tables must not contain a line break. Otherwise the table is broken.
2020-01-25 13:28:15 +01:00
benpicco
43b736969b
Merge pull request #13138 from francois-berder/pic32-docs
...
boards: Improve documentation for pic32-clicker and pic32-wifire
2020-01-24 17:48:43 +01:00
Francois Berder
f4404f2df6
boards: pic32-wifire: Improve documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-01-24 09:49:09 +00:00
Francois Berder
f1e1de5710
boards: pic32-clicker: Improve documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-01-24 09:49:09 +00:00
benpicco
358a2625fc
Merge pull request #13136 from jeandudey/2020_01_15-cc2538dk-resc
...
boards: cc2538dk: remove `machine SetClockSource`.
2020-01-24 10:45:59 +01:00
Marian Buschsieweke
f58b82bd39
Merge pull request #13163 from gschorcht/board/mega-xplained/fix_adc_lines
...
boards/mega-xplained: fix ADC line defintions
2020-01-23 11:34:38 +01:00
Jean Pierre Dudey
a73f3809cc
cpu/cc13x2: rename cc13x2 cpu to cc26x2_cc13x2
...
The CC26x2 and CC13x2 share the same register definitions, and both are
treated equally in the TI's technical reference manual. [1]
- To avoid confusions in the future I renamed it to `cc26x2_cc13x2`.
- Documentation was updated.
- The `cc1312-launchpad` board that uses the `cc13x2` MCU was updated.
- The `cc1352-launchpad` board that uses the `cc13x2` MCU was updated.
[1]: https://www.ti.com/lit/ug/swcu185d/swcu185d.pdf
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-01-20 09:31:48 -05:00
Jean Pierre Dudey
f96fc62369
cc1352-launchpad: fix documentation errors.
...
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-01-20 08:05:52 -05:00
Jean Pierre Dudey
cc170e9987
cc1352-launchpad: remove export from XDEBUGGER
...
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-01-20 08:04:54 -05:00
Jean Pierre Dudey
a6117ff0a2
cc1352-launchpad: enable periph_gpio_irq.
...
This feature is supported by the processor.
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-01-20 08:04:02 -05:00
97cb4c5707
Merge pull request #13134 from jeandudey/2020_01_15-cc1312-launchpad
...
boards: add cc1312-launchpad board.
2020-01-20 07:39:38 +01:00
Jean Pierre Dudey
633aa8cd41
boards: add cc1312-launchpad board.
...
This is mostly based on the cc1352-launchpad boards, is essentially the same
buttons and leds pins, what changes is the CCXML files used to flash with
`make flash` and the UART pins.
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-01-19 11:36:31 -05:00
Gunar Schorcht
f53534ed44
boards/mega-xplained: fix ADC line defintions
...
For the ATmega platform the ADC lines are not defined according to the GPIOs. Instead, they are defined from 0 to ADC_NUMOF-1, which in turn represents the bit in the corresponding ADC registers. The mapping from the line number to the corresponding ADC register/bit combination is done implicitly by the periph/adc implementation.
2020-01-18 13:19:11 +01:00
9ae80f56d1
pinetime: Fix battery ADC line define
2020-01-18 11:15:04 +01:00
c4877c6d41
Merge pull request #13141 from gschorcht/cpu/esp32/fix_c_linkage
...
cpu/esp32: fix C linkage compilation error
2020-01-16 15:06:01 +01:00
Gunar Schorcht
416e8ce8e6
cpu/esp32: fix C linkage compilatio error
...
With the new toolchain version required to fix issue #13133 , the compilation of `examples/posix_socket` fails due to a C linkage error in `atomic_base.h`. The reason is that including `drivers/include/mtd.h` in `boards/esp32/board_common.h` inside the `extern C` block finally leads to including `atomic_base.h` inside the `extern C` block which in turn to the C linkage error for the template definitions in this file.
2020-01-16 13:03:49 +01:00
81dbba2588
boards/pinetime: fix jlink rtt configuration
2020-01-15 22:12:06 +01:00
Martine S. Lenders
78b5c1ee5c
boards: initial import of Adafruit Feather nRF52840 Express
...
This provides support initial support for the [Adafruit Feather nRF52840
Express][feather-nrf52840]. The current feature set includes:
- Default flashing via Segger J-Link
- UART, SPI, and I2C exposed in accordance to the Feather [pinout]
- SAUL support for on-board LEDs and button
[feather-nrf52840]: https://learn.adafruit.com/introducing-the-adafruit-nrf52840-feather/
[pinout]: https://cdn-learn.adafruit.com/assets/assets/000/046/243/original/adafruit_products_Feather_M0_Adalogger_v2.2-1.png
[pid.codes]: http://pid.codes/1209/7D00/
2020-01-15 22:11:58 +01:00
3b4fe41296
Merge pull request #13130 from kaspar030/ili9341_resolution_param
...
drivers/ili9341: add number of lines parameter
2020-01-15 18:33:14 +01:00
Jean Pierre Dudey
94ca53c3b9
boards: cc2538dk: remove machine SetClockSource.
...
It causes errors on current Renode versions. It wasn't documented on the
Renode changelog, but SetClockSource property was removed. Before this
change it showed this error:
There was an error executing command 'machine SetClockSource cpu'
machine does not provide a field, method or property SetClockSource.
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-01-15 11:44:02 -05:00
47634addf3
boards/pinetime: configure ili9341 LCD number of lines
2020-01-15 15:36:21 +01:00
76b9cfb677
Merge pull request #12973 from fjmolinas/pr_atmega_tx_isr
...
cpu/atmega_common/periph/uart: use TX_ISR to check TX end
2020-01-15 11:51:22 +01:00
Hauke Petersen
8b408fc828
Merge pull request #12724 from aabadie/pr/stdio_rtt_blacklist
...
make: improve handling of the stdio_rtt module, improve dependency management at application level
2020-01-15 10:12:13 +01:00
Francisco Molina
fb388bf5b6
boards/atmega/include/periph_conf_atmega_common: add USARTn_TX_vect
2020-01-15 10:02:41 +01:00
fcec59261c
Merge pull request #12552 from kaspar030/add_pinetime_support
...
boards: add initial support for the PINE64 PineTime smartwatch
2020-01-15 09:51:40 +01:00
630ff1425a
Merge pull request #13125 from francois-berder/clicker-pic32prog
...
boards: pic32-clicker: Use pic32prog as default programmer
2020-01-15 07:08:31 +01:00
benpicco
2ff710c762
Merge pull request #12669 from benpicco/mcb2388
...
boards: add mcb2388
2020-01-14 22:46:49 +01:00
Benjamin Valentin
9183d16278
boards: add mcb2388
...
The MCB2388 Evaluation Board is a development board for the LPC2388 MCU.
LPC2388 and LPC2387 are very simmilar, the only difference is added USB Host
support.
Since this is not used yet, I chose to just pretend it's an lpc2387.
So far, only the two UARTs, LEDs and LCD display are configured.
2020-01-14 21:21:08 +01:00
5c21df5fee
boards/pinetime: initial support for the PINE64 PineTime smartwatch
2020-01-14 21:06:43 +01:00
Francois Berder
634fea8347
boards: pic32-clicker: Use pic32prog as default programmer
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-01-14 19:43:13 +00:00
8d16ccb96a
Merge pull request #13115 from basilfx/feature/slstk3401a_doc_fixes
...
boards/slstk3401a: update documentation
2020-01-14 17:00:03 +01:00
ef947d3495
Merge pull request #13114 from basilfx/feature/slstk3402a_doc_fixes
...
boards/slstk3402a: update documentation
2020-01-14 16:59:52 +01:00
a1850773ff
Merge pull request #13116 from basilfx/feature/stk3600_docs
...
boards/stk3600: add documentation
2020-01-14 16:00:35 +01:00
f3476452cb
Merge pull request #13117 from basilfx/feature/stk3700_docs
...
boards/stk3700: add documentation
2020-01-14 15:28:27 +01:00
628f085f37
Merge pull request #13118 from basilfx/feature/slwstk6000b_docs
...
boards/slwstk6000b: add documentation
2020-01-14 15:02:49 +01:00
5de5616c92
Merge pull request #13113 from basilfx/feature/sltb001a_doc_fixes
...
boards/sltb001a: update documentation
2020-01-14 15:02:34 +01:00
Martine Lenders
7430ea98ed
Merge pull request #13096 from nmeum/pr/fix_asan_target
...
boards/native: fix all-asan Makefile target
2020-01-14 13:43:22 +01:00
Francisco
f76f7c73ce
Merge pull request #12957 from aabadie/pr/cpu/fe310_spi
...
cpu/fe310: add spi peripheral driver
2020-01-14 10:54:47 +01:00
Bas Stottelaar
4f3083793d
Merge pull request #13099 from basilfx/feature/ikea_tradfri_modules
...
boards/ikea-tradfri: add board documentation.
2020-01-14 10:25:53 +01:00
Francisco
a6cf5cf3f9
Merge pull request #12946 from aabadie/pr/cpu/fe310_i2c
...
cpu/fe310: add i2c peripheral driver
2020-01-14 10:20:11 +01:00
57d5a1db1c
boards: provide stdio_rtt as default module where required
...
For the moment, hamilton, ruuvitag and thingy52 use stdio_rtt by default.
2020-01-14 07:48:08 +01:00
Bas Stottelaar
12ec03d2e0
boards/sltb001a: update documentation
2020-01-13 23:38:43 +01:00
Bas Stottelaar
8f22110210
boards/slstk3402a: update documentation
2020-01-13 23:38:10 +01:00
Bas Stottelaar
488c545674
boards/slstk3401a: update documentation
2020-01-13 23:37:40 +01:00
Bas Stottelaar
52ecf0fcc1
boards/stk3600: add documentation
2020-01-13 23:37:02 +01:00
Bas Stottelaar
b9b8358175
boards/stk3700: add documentation
2020-01-13 23:36:29 +01:00
Bas Stottelaar
aeed1f3153
boards/slwstk6000b: add documentation
2020-01-13 23:31:51 +01:00
Bas Stottelaar
8a98bf5260
boards/ikea-tradfri: add board documentation.
2020-01-13 21:40:00 +01:00
Leandro Lanzieri
50f1b1423a
Merge pull request #12999 from fjmolinas/pr_native_makefile_include_explicit_path
...
boards: use explicit paths for file inclusion
2020-01-13 16:00:48 +01:00
Francisco Molina
74cecf30f0
boards/common/arduino-mkr: remove /Makefile.dep
...
Makefile.dep is already included for the board no need to do it here.
2020-01-13 11:53:48 +01:00
Francisco Molina
5a8f996111
boards: replace use of $(BOARD) by explicit name
...
With the introduction of BOARDSDIR external boards can re-use common
code of BOARDS present in RIOTBASE. To be able to do this file
references may not use $(BOARD) since BOARD will be set by the
external BOARD.
2020-01-13 11:53:48 +01:00
MichelRottleuthner
53cb3b087c
Merge pull request #9530 from Hyungsin/forupstream_xtimer
...
sys: xtimer concurrency/robustness improvement
2020-01-13 08:24:15 +01:00
Sören Tempel
e2b8231796
boards/native: fix crash with all-asan
...
Without this change a RIOT application compiled with all-asan will
segfault as RIOT provides its own malloc by default. Add a define for
disabling custom malloc, calloc and realloc implementations and use it
when compiling with all-asan.
2020-01-12 16:17:48 +01:00
Francois Berder
237f7363fa
boards: pic32-wifire: Do not include vendor header in board header
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-01-11 17:11:35 +00:00
8405fbe611
boards/hifive1*: provide and configure SPI feature
2020-01-11 13:06:39 +01:00
b3658ad95e
boards/hifive1b: provide i2c configuration
2020-01-11 13:06:10 +01:00
Hyungsin
6eed5b9d43
remove XTIMER_OVERHEAD
2020-01-10 13:22:11 -08:00
b42cf186fe
boards/hifive1*: remove gpio interrupt definition
...
This macro is now defined in periph_cpu.h
2020-01-10 16:41:33 +01:00
473f1d7147
boards/hifive1*: cleanup board initialization
2020-01-10 16:41:33 +01:00
97ef5d53de
boards/hifive1*: rework clock configuration
2020-01-10 16:41:33 +01:00
39cf4d38c1
boards/hifive1*: move xtimer definitions to board.h
2020-01-10 16:41:32 +01:00
Yegor Yefremov
8101f52e3f
boards/esp32: add TTGO T-Beam board definition
...
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2020-01-10 10:04:38 +01:00
267e273c56
boards/hifive1b: set custom reset delay of 1s for tests
2020-01-10 08:34:45 +01:00
2bcf1890bb
boards/remote*: factorize provided features
2020-01-08 14:42:03 +01:00
43a9529ed2
boards/remote: remove unused periph_common.h
2020-01-08 14:41:31 +01:00
c70a14ff89
boards/remote*,firefly: use common config headers
2020-01-08 14:40:20 +01:00
4a0ac8e4e8
boards/remote: add common default config headers
2020-01-08 14:38:52 +01:00
ce0bb35587
Merge pull request #12993 from fjmolinas/pr_cc2538_rtt
...
cpu/cc2538: add periph_rtt
2020-01-08 09:55:45 +01:00
Francisco Molina
b436ba4a0c
boards/common/remote: add periph_rtt
2020-01-08 09:16:49 +01:00
Francisco Molina
59ada62930
boards/openmote-b: add periph_rtt
2020-01-08 09:16:49 +01:00
748ffff931
boards/nrf52: remove use of export for LINKER_SCRIPT
2020-01-03 16:07:15 +01:00
c71e931d77
boards/native: remove use of export for LINKFLAGS
2020-01-02 09:47:33 +01:00
kcant
3a29d346ef
Relink wiki.stm32duino.com to web.archive.org ( #13011 )
...
wiki.stm32duino.com broken links correction
2019-12-28 18:39:22 +01:00
kcant
f770c6fffd
Update doc.txt
...
Broken links correction to https://web.archive.org/web/20190428082446/ *
2019-12-28 18:38:27 +01:00
dylad
fc9549b069
boards/sam0: update sam0-based board to use hw fc
2019-12-20 21:26:56 +01:00
876824201c
boards/hifive1*: apply new UART configuration scheme
2019-12-20 15:22:09 +01:00
326d570b11
Merge pull request #12990 from fjmolinas/pr_b-l475e-iot01a_assert_srst
...
boards/b-l475e-iot01a: set OPENOCD_RESET_USE_CONNECT_ASSERT_SRST
2019-12-19 15:10:08 +01:00
Francisco Molina
b4a8cf8351
boards/b-l475e-iot01a: set OPENOCD_RESET_USE_CONNECT_ASSERT_SRST
...
b-l475e-iot01a can become unflashable when hardfaults occure.
To make sure flashing succeeds `connect_assert_srst` is called
before connecting to flash through openocd.
2019-12-19 14:21:27 +01:00
Hauke Petersen
3330676fd5
boards/nrf52840dk: disable UART HWFC
2019-12-18 11:53:26 +01:00
Francisco
927b03f0ff
Merge pull request #12902 from aabadie/pr/boards/hifive1b_arduino
...
boards/hifive1b: add arduino feature
2019-12-16 13:31:17 +01:00
0ef371899d
boards/hifive1b: add arduino feature
2019-12-13 16:25:11 +01:00
Hauke Petersen
d0375ea119
boards/native: fix default value of PORT
2019-12-13 11:36:57 +01:00
benpicco
03b95ef833
Merge pull request #12883 from fabian18/microduino-corerf-doc-pin-mapping
...
boards/microduino-corerf: doc SPI and I2C pin mapping
2019-12-05 21:14:05 +01:00
fabian18
f3f4c3b4b8
boards/microduino-corerf: doc SPI and I2C pin mapping
2019-12-05 19:43:35 +01:00
e5d5892167
boards/hifive1*: remove periph_gpio provided features
...
There are now provided at cpu level
2019-12-05 15:27:12 +01:00
Marian Buschsieweke
cf0fb1dff1
Merge pull request #12868 from benpicco/lpc2k-fix
...
lpc2k_pgm: fix build warnings, add lpc2388
2019-12-05 13:02:19 +01:00
Benjamin Valentin
472373637c
boards/microduino-corerf: enable RTT
...
The board *does* have a crystal oscillator connected, so we can
enable RTT.
2019-12-04 22:45:18 +01:00
Benjamin Valentin
e958798225
boards/microduino-corerf: use 115200 baud for stdio
...
The MCU can handle that baud rate just fine.
A standard baud rate is much easier to use than those awkward 57600 baud.
2019-12-04 22:43:41 +01:00
Benjamin Valentin
9ce34bb305
lpc2k_pgm: fix build warnings
...
GCC now warns when snprintf()ing a buffer that, together with the
format string, might be larger than the destination buffer.
To fix this increase the size of the destination buffer so that
the source buffer and the format string will always fit - 32 bytes
are enough.
2019-12-03 22:09:29 +01:00
Benjamin Valentin
a57f380259
lpc2k_pgm: add LPC2388
...
The device is very simmilar to the LPC2387
2019-12-03 22:09:20 +01:00
Martine Lenders
2f74d9d644
Merge pull request #12517 from miri64/native/enh/reset-command
...
native: allow for native to be resetable via SIGUSR1
2019-12-03 10:56:11 +01:00
Martine Lenders
d670f77d91
native: add and use reset script to reset certain PID
2019-12-03 09:51:52 +01:00
Benjamin Valentin
6f41ecc74b
boards: ATmega: enable periph_rtt for boards with 32kHz crystal
...
The RTT on ATmega only works if the board provides a 32kHz oscillator.
2019-12-01 17:26:24 +01:00
MrKevinWeiss
ebe010125b
boards/openmote-b: fix button pin define
...
According to the schematics user button should be on `PD5` not `PC5`
(so `GPIO_PIN(3, 5)`).
Due to the super high values resistors being used for the external
pullup it seems if you use a internal pullup it doesn't work.
2019-11-29 11:10:24 +01:00
Benjamin Valentin
70eef51cd8
boards/openmote-b: fix naming of RF24 switch pins.
...
The Sub-GHz Antenna of the Openmote-B is always connected to the AT86RF215.
It is the 2.4 GHz radial that can be switched between the CC2538 and the AT86RF215.
This changes the name of the defines accordingly.
2019-11-29 10:59:59 +01:00
benpicco
e81d040a26
Merge pull request #12799 from chudov/derfmega-PR
...
boards/derfmega*: initial support
2019-11-28 13:57:56 +01:00
chudov
0a151a78da
boards/derfmega*: initial support
2019-11-27 20:53:14 +01:00
Benjamin Valentin
0d977b3b3c
cpu/sam0_common/periph/uart: implement buffered write
...
Implement interrupt based uart_write() using a tsrb for the TX buffer.
To enable it, add
USEMODULE += periph_uart_nonblocking
to your Makefile.
2019-11-27 19:01:00 +01:00
Francisco Molina
90bcb016bb
boards: unexport PROGRAMMER
2019-11-27 14:31:01 +01:00
743d7170e2
Merge pull request #12804 from wosym/nucleo-f207zg_ethernet
...
boards/nucleo-f207zg: add ethernet configuration
2019-11-26 12:44:19 +01:00
Wouter
3072900ed6
boards/nucleo-f207zg: add Ethernet config
2019-11-26 11:11:41 +01:00
benpicco
7f40b13d05
Merge pull request #12697 from maribu/stm32-programmer
...
boards: Common STM32 programmer/debugger/serial config
2019-11-25 15:27:22 +01:00
4d0d52dd0e
boards/z1: fix typos
2019-11-23 22:39:35 +01:00
5468ab41bd
boards/yunjia-nrf51822: fix typos
2019-11-23 22:39:35 +01:00
a8351a7296
boards/thingy52: fix typos
2019-11-23 22:39:35 +01:00
02b1cf170f
boards/telosb: fix typos
2019-11-23 22:39:35 +01:00
be61dbe2ac
boards/stm32l0538-disco: fix typos
2019-11-23 22:39:35 +01:00
97a18f9114
boards/stm32f723e-disco: fix typos
2019-11-23 22:39:35 +01:00
9b6ae21817
boards/sensebox_samd21: fix typos
2019-11-23 22:39:35 +01:00
11073a73e1
boards/saml21-xpro: fix typos
2019-11-23 22:39:35 +01:00
f69af0edda
boards/remote-revb: fix typos
2019-11-23 22:39:35 +01:00
4e06b71e8d
boards/remote-reva: fix typos
2019-11-23 22:39:35 +01:00
081f1e80e7
boards/remote-pa: fix typos
2019-11-23 22:39:35 +01:00
ef3b8b15e0
boards/p-l496g-cell02: fix typos
2019-11-23 22:39:35 +01:00
9f2aa74635
boards/nucleo-l4r5zi: fix typos
2019-11-23 22:39:07 +01:00
147696a0fc
boards/msba2: fix typos
2019-11-23 22:39:07 +01:00
daffa544a2
boards/microbit: fix typos
2019-11-23 22:39:07 +01:00
f61175219b
boards/mbed_lpc1768: fix typos
2019-11-23 22:39:07 +01:00
edfa34303b
boards/lsn50: fix typos
2019-11-23 22:39:07 +01:00
e6d3963cd4
boards/iotlab-m3: fix typos
2019-11-23 22:39:07 +01:00
60e2ce8702
boards/frdm-k64f: fix typos
2019-11-23 22:39:07 +01:00
5a4bad8dfa
boards/fox: fix typos
2019-11-23 22:39:07 +01:00
a394fcd100
boards/esp32-wrover-kit: fix typos
2019-11-23 22:39:07 +01:00
8e52d30949
boards/esp32-wroom-32: fix typos
2019-11-23 22:39:07 +01:00
fbc54466f8
boards/esp32-wemos-lolin-d32-pro: fix typos
2019-11-23 22:39:07 +01:00
557f005cb1
boards/esp32-olimex-evb: fix typos
2019-11-23 22:39:07 +01:00
dcd48cbd23
boards/esp32-mh-et-live-minikit: fix typos
2019-11-23 22:39:07 +01:00
4fb244d415
boards/common: fix typos
2019-11-23 22:39:07 +01:00
6a191fe9ff
boards/cc2650stk: fix typos
2019-11-23 22:39:07 +01:00
b0f1e3dbb9
boards/blackpill-128kib: fix typos
2019-11-23 22:39:07 +01:00
90964e4398
boards/blackpill: fix typos
2019-11-23 22:39:07 +01:00
196cf2d776
boards/arduino-leonardo: fix typos
2019-11-23 22:39:07 +01:00
723707b7fa
boards/airfy-beacon: fix typos
2019-11-23 22:39:07 +01:00
benpicco
d244b0fe59
Merge pull request #12787 from gschorcht/cpu/esp32/netdev_default
...
cpu/esp*: define esp_now as default netdev
2019-11-23 14:59:54 +01:00
Gunar Schorcht
72967f8fc3
cpu/esp32: GNRC_NETIF_NUMOF is handled in CPU makefile
...
Since Makefile.dep files are included as last files multiple times to resolve all module dependencies, GNRC_NETIF_NUMOF is handled here.
2019-11-22 17:38:35 +01:00
Francisco
3c60afc083
Merge pull request #12768 from aabadie/pr/boards/pic32-clicker-uart-cleanup
...
boards/pic32-clicker: cleanup uart configuration and initialization, cleanup header includes
2019-11-22 17:20:40 +01:00
Hauke Petersen
96c6313bd4
boards/avr-rss2: use bme280_i2c module
2019-11-22 14:04:38 +01:00
Hauke Petersen
f46731801a
boards/sltb001a: use i2c mode of bme280 driver
2019-11-22 14:04:37 +01:00
Hauke Petersen
3c0d5048f9
board/ruuvitag: enable bme280 for saul default
2019-11-22 14:04:37 +01:00
401abd5b71
boards/pic32-clicker: cleanup includes
2019-11-22 08:12:47 +01:00
e8b0399bc9
boards/pic32-clicker: cleanup uart initialization
2019-11-22 08:12:46 +01:00
Gunar Schorcht
a05027cdba
Merge pull request #12523 from aabadie/pr/sys/arduino_pwm
...
sys/arduino: add implementation for analogWrite
2019-11-21 15:08:10 +01:00
4337cb316f
Merge pull request #12752 from gschorcht/cpu/esp32/espreset
...
boards/esp32*: use espreset tool for reset in make test
2019-11-20 22:07:15 +01:00
Robert Olsson
c903bc8c1b
boards/avr-rss2: add AtMega256RFR2 based board
...
Co-Authored-By: benpicco <benpicco@googlemail.com>
Support: Alexandre Abadie aabadie, Marian Buschsieweke maribu, Martine Lenders miri64
2019-11-20 11:57:02 +01:00
Gunar Schorcht
5ba4a7d7cf
boards/esp32*: espreset tool added
2019-11-20 08:33:47 +01:00
benpicco
1999e2f89c
Merge pull request #12745 from benpicco/atmega-led_fix
...
boards/atmega_common: remove weak led_init()
2019-11-20 00:14:48 +01:00
benpicco
cfcbb76cd2
Merge pull request #12729 from maribu/atmega1284p
...
boards/atmega1284p: Add ATmega1284P as board
2019-11-19 23:18:31 +01:00
Hauke Petersen
04dcc3662b
Merge pull request #12344 from chrysn-pull-requests/particle-antenna-switch
...
particle-*: Configure antenna switch
2019-11-19 23:06:29 +01:00
Benjamin Valentin
c277100dd9
boards/atmega_common: remove weak led_init()
...
`led_init()` is already protected by an `#ifdef`, so no need for
the weak symbol.
The problem is that the weak function does not get overridden, even when
the board provides it's own led_init(), resulting in no LEDs being
initialized.
2019-11-19 22:36:07 +01:00
Marian Buschsieweke
b7150ed6c7
boards/common/atmega: Added ATmega1284P PWM conf
...
Added PWM configuration for the ATmega1284P CPU; this can be reused for every
board featuring that CPU.
2019-11-18 23:46:08 +01:00
chrysn
9954194ae0
particle boards: Make default antenna selection configurable
...
The setter function approach makes this switchable at runtime (antenna
diversity?).
Documentation is added both to the board introduction page and the
individual pins and functions.
2019-11-18 13:54:39 +01:00
chrysn
951f7dec2c
particle-*: Configure antenna switch
...
The particle-{argon,boron,xenon} all have a uFL connector and a PCB
antenna for 2.4GHz radio, connected by a SKY13351-378LF switch
configured by a VCTL[12] pin pair.
This sets the default configuration to use the PCB antenna, as driving
an unconnected antenna will deteriorate radio performance.
2019-11-18 13:54:22 +01:00
588766ab27
Merge pull request #12733 from fjmolinas/pr_jlink_serial
...
makefiles/tools/jlink.inc.mk: DEBUG_ADAPTER_ID as JLINK_SERIAL
2019-11-18 13:47:26 +01:00
Francisco Molina
f9ebc8658f
dist/tools/jlink: cleanup doc
2019-11-18 13:04:42 +01:00
Kevin "Tristate Tom" Weiss
be39169bd4
Merge pull request #11108 from gschorcht/cpu/esp8266/esp-idf/pr
...
cpu/esp8266: complete reimplementation based on ESP8266 RTOS SDK
2019-11-18 09:34:49 +01:00
Marian Buschsieweke
f4089d08fe
boards/atmega328p: Fixed doc
...
- Use proper IEC units for sizes
- Added info on EEPROM
- Fixed incorrect info on default fuse settings
- Added info on how to unlock 8MHz
2019-11-18 00:16:43 +01:00
Marian Buschsieweke
8f03c7561a
boards/atmega1284p: Add ATmega1284P as board
...
The ATmega1284P can be run on a breadboard with no external components, except
for a power supply and (if access to the serial is required) an USB-TTL adapter.
This commit adds it as a "board".
2019-11-17 14:10:12 +01:00
Benjamin Valentin
60686c96dc
boards/common: clean up msba2 common files
...
The 'msba2' common files have accumulated many empty files are files that
do nothing.
This makes reasoning about the boards needlessly difficult.
Trim down on `common/msba2/` so that it now only contains the setup for the
UART/bootloader based flashing.
This should eventuelly be moved to `makefiles/tools/`
2019-11-16 11:57:15 +01:00
65e0247a9b
boards/arduino-atmega: add mapping for Arduino PWM pins
2019-11-15 17:54:30 +01:00
e0f288421d
boards/sodaq-autonomo: add mapping for Arduino PWM pins
2019-11-15 17:51:45 +01:00
d03c982ddb
boards/arduino-mkr: add mapping for Arduino PWM pins
2019-11-15 17:51:45 +01:00
f1cb14730d
boards/arduino-zero: add mapping for Arduino PWM pins
2019-11-15 17:51:45 +01:00
Gunar Schorcht
555a7040db
cpu/esp8266: reset tool to allow automatic tests
2019-11-14 13:58:48 +01:00
Gunar Schorcht
e5b7645b0b
boards/esp32: changes for RTOS SDK
2019-11-14 13:58:25 +01:00
Gunar Schorcht
7d9a3a79a2
boards/esp8266: changes for RTOS SDK
2019-11-14 13:58:25 +01:00
253c75ab6b
Merge pull request #12703 from haukepetersen/fix_nrfboards_blefeat
...
nrf5x: move nimble_ble feat. to cpu
2019-11-13 19:07:48 +01:00
Francisco
9691cb68d6
Merge pull request #12662 from aabadie/pr/boards/hifive1_port_fix
...
boards/hifive1b: fix Linux default serial port
2019-11-13 18:04:22 +01:00
Hauke Petersen
4bf14822cb
nrf5x: move nimble_ble feat. to cpu
2019-11-13 13:43:55 +01:00
Marian Buschsieweke
c510ad858c
boards/common/blxxxpill: Use STM32 programmer conf
2019-11-12 19:48:05 +01:00
Marian Buschsieweke
a949179f69
boards/stm32f030f4-demo: Use STM32 programmer conf
2019-11-12 19:46:29 +01:00
Marian Buschsieweke
92284bed88
boards/common/nucleo: Use STM32 programmer config
2019-11-12 19:43:42 +01:00
benpicco
f77e5a6c6a
Merge pull request #12673 from benpicco/purge-rtc_numof
...
boards: remove RTT_NUMOF/RTC_NUMOF
2019-11-12 11:33:16 +01:00
Benjamin Valentin
0ea2cbf1eb
boards: remove RTT_NUMOF/RTC_NUMOF
...
Those macros are defined but never used.
2019-11-08 14:20:33 +01:00
Marian Buschsieweke
9a0657af9b
boards: Refactored avsextrem & msba2
...
- Removed features already provided at CPU level
- Sorted features alphabetically
2019-11-08 14:02:42 +01:00
Leandro Lanzieri
66d5e4d05f
Merge pull request #12637 from benpicco/lpc2387-uart
...
cpu/lpc2387: update the UART driver
2019-11-07 22:21:50 +01:00
Benjamin Valentin
9e68556393
boards/msba2: configure remaining UARTs
...
All UARTs on the MSBA2 are exposed through pin headers on the board.
Configure them according to the data sheet.
2019-11-07 21:55:25 +01:00
Benjamin Valentin
90aef98ca0
boards/avsextrem: adapt to updated UART driver
2019-11-07 21:55:25 +01:00
Benjamin Valentin
3e053d1db9
boards/msba2: adapt to updated UART driver
2019-11-07 21:55:25 +01:00
2e7534ddee
boards/hifive1b: fix default serial port
...
The board provides a JLink adapter which is exposed as /dev/ttyACMx on Linux. STDIO UART is available on this port
2019-11-07 14:14:05 +01:00
42c4b7d34d
boards/atmega256rfr2-xpro: use 115200 baudrate for STDIO
2019-11-06 12:46:28 +01:00
485bfc45da
boards/atmega256rfr2-xpro: document how to configure the fuses
...
This is important for a correct configuration of the external 16MHz oscillator
2019-11-06 12:46:28 +01:00
498cbe9bbc
boards/atmega256rfr2-xpro: configure external 16MHz oscillator
2019-11-06 12:46:28 +01:00
Marian Buschsieweke
d02ed3a3ff
Merge pull request #12646 from maribu/atmega328p-timer
...
boards/atmega328p: Fixed xtimer frequency
2019-11-05 22:19:09 +01:00
Marian Buschsieweke
f55e438d56
boards/atmega328p: Fixed xtimer frequency
...
The ATmega328p on a breadboard can have various frequencies depending on
the fuse settings and whether and which crystal is connected. Thus, finding a
fixed xtimer frequency that can be configured for every CPU core clock with the
available prescalers is not possible. Therefore, the fixed frequency is replaced
by a frequency depending on the CPU clock speed. For CPU clock frequency of
more than 4 MHz a prescaler of 64 will be chosen (same as on the Arduino Uno),
for 4 MHz and less a prescaler of 8 will be chosen.
2019-11-05 19:32:29 +01:00
f24a3802c7
boards/atmega256rfr2-xpro: configure debug
2019-11-05 10:40:32 +01:00
4751892ce9
boards/atmega256rfr2-xpro: initial support
2019-11-05 10:40:32 +01:00
Gunar Schorcht
7d63158e06
boards/esp32-wroom-32: fixes a broken image link
2019-11-02 18:31:45 +01:00
benpicco
ed93bce856
Merge pull request #9323 from OYTIS/cc1352-launchpad-support
...
CC1352 launchpad support
2019-10-30 14:06:13 +01:00
Marian Buschsieweke
fa3651f275
boards/microduino-corerf: Minor doc tweaks
...
- Using @warning Doxygen command to make warning more visible
- Used IEC units for size specifications
- Aligned markdown source of the table
- Added note that the 5V pin is not connected to the board and cannot be used
to power the board
2019-10-30 08:51:34 +01:00
Anton Gerasimov
9fad1e3b6d
cpu/cc26xx_cc13xx: define uart_conf_t
...
Replaces older macro-based configuration
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
2019-10-29 21:27:00 +01:00
Anton Gerasimov
a60d8f471f
boards/cc1352-launchpad: Add support for CC1352R Launchpad
...
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
2019-10-29 21:27:00 +01:00
Anton Gerasimov
f6a3f14d22
cpu/cc26x0: Factor out code common for cc26xx/cc13xx family
...
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
2019-10-29 21:27:00 +01:00
Benjamin Valentin
3ecf7a0430
boards/msba2: define XTAL frequency
...
The board comes with a 16 MHz XTAL.
Since the avsextrem is just an extended msba2, this is true here too.
2019-10-27 01:32:50 +02:00
7761169964
Merge pull request #11657 from Yanok35/pr-stm32-spi-af
...
boards/stm32-based: allow SPI signals routed on multiple alternate functions
2019-10-25 09:47:49 +02:00
b0dfda244b
Merge pull request #12460 from fjmolinas/pr_port_migration
...
makefiles/vars.inc.mk: introduce and use `PROG_DEV`
2019-10-25 09:40:20 +02:00
Yannick Gicquel
d37adee32d
boards/stm32-based: allow SPI signals routed on multiple alternate functions
...
There is no hardware limitation for custom boards based on STM32 to uses
SPI bus with signals coming from different PORT and alternate functions.
This patch allow alternate's function definition per pin basis, thus enable
the support of SPI bus signals routed on differents PORT.
Signed-off-by: Yannick Gicquel <ygicquel@gmail.com>
2019-10-25 06:27:41 +02:00
Marian Buschsieweke
ef97b874bf
boards/native: Default to C11 instead of C99
2019-10-24 21:57:02 +02:00
Francois Berder
2d68b16c94
boards: pic32-clicker: Do not include vendor header in board header
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2019-10-24 19:01:02 +01:00
Francisco Molina
1ae0873769
boards: change PORT used for flash/debug/reset to PROG_DEV
2019-10-24 12:58:12 +02:00
Francisco Molina
755b4d97da
boards/(openmote-b/remote): migrate PORT_BSL to PROG_DEV
...
- Move serial.inc.mk in remote and openmote-b Makefile.include before
PROG_DEV to avoid repeating OS logic check
- Add deprecation warning for PORT_BSL
2019-10-24 12:57:46 +02:00
Francisco Molina
bf25e12602
makefiles/tools/avrdude.inc.mk: migrate to use PROG_DEV
...
- Move serial.inc.mk in mega-xplained/Makefile.include after
PROG_DEV so PROG_DEV can still default to PORT
- Add deprecation warning for arduino-leonardo and mega-xplained
2019-10-24 12:57:07 +02:00
f84cdc4044
boards/sodaq: restore accidentally removed arduino feature
2019-10-22 19:06:16 +02:00
Francisco
88a6ad9df8
Merge pull request #12541 from aabadie/pr/boards/arduino_zero_adc
...
boards/arduino-zero: configure ADC channels
2019-10-22 15:56:38 +02:00
26c0b812d2
Merge pull request #12531 from fjmolinas/pr_nrf52_nimble
...
common/nrf52840/Makefile.dep: nrf802154 if no nimble_%
2019-10-22 15:14:54 +02:00
76ca2f5a08
boards/arduino-zero: configure ADC channels
2019-10-22 11:19:26 +02:00
benpicco
d49c48368a
Merge pull request #12438 from aabadie/pr/boards/sodaq_factorize
...
boards/sodaq: factorize common code
2019-10-21 17:04:20 +02:00
Francisco Molina
c04a2cf3a3
common/nrf52840/Makefile.dep: nrf802154 if no nimble_%
2019-10-21 16:52:18 +02:00
Benjamin Valentin
a97e0543cb
boards: add stm32f030f4-demo
...
The board is a very cheap (< 1€) breakout board for the stm32f030f4 MCU.
2019-10-21 15:30:22 +02:00
benpicco
ca7e82c312
Merge pull request #11090 from maribu/atmega328p
...
boards: Added standalone ATmega328p
2019-10-21 13:38:58 +02:00
4b06a11b93
Merge pull request #12470 from aabadie/pr/boards/kw41z_openocd
...
boards/frdm: update openocd version requirements
2019-10-21 13:30:54 +02:00
Marian Buschsieweke
f9c2f26dd0
boards: Added standalone ATmega328p
2019-10-21 12:54:46 +02:00
536809cdca
boards/sodaq-*: use common code
2019-10-21 08:33:11 +02:00
f9631953cb
boards: add common sodaq module
2019-10-21 08:33:11 +02:00
5578740fc4
Merge pull request #12397 from fjmolinas/pr_CPU_ARCH_FAM
...
makefiles/vars.inc.mk: move definition and export of CPU_FAM and CPU_ARCH to vars.inc.mk
2019-10-21 08:23:51 +02:00
14567ea973
Merge pull request #12494 from fjmolinas/pr_remove_OS
...
Makefile/include: use ony one call to `uname`
2019-10-18 15:03:10 +02:00
benpicco
29e5c3af67
Merge pull request #12490 from aabadie/pr/boards/efm32_common_periph_gpio
...
boards/efm32: move provided gpio features at cpu level
2019-10-18 11:19:33 +02:00
benpicco
34ee36d9e4
Merge pull request #12491 from aabadie/pr/boards/atmega_common_periph_gpio
...
boards/atmega: move provided gpio features at cpu level
2019-10-18 11:19:15 +02:00
benpicco
4ed04208ea
Merge pull request #12492 from aabadie/pr/boards/cc2538_common_periph_gpio
...
boards/cc2538: move provided gpio features at cpu level
2019-10-18 11:18:54 +02:00
Francisco Molina
45c8eafd42
Makefile.include: remove repeated OS declaration
2019-10-18 10:36:43 +02:00
4d85735b24
boards/slwstk6220a: remove useless provided gpio features
...
These are provided at CPU level.
2019-10-18 09:35:00 +02:00
aed0cfb1d8
boards/efm32: remove useless provided gpio features
...
These features are provided at CPU level
2019-10-18 09:33:54 +02:00
Francisco Molina
347a0fc804
cpu/ boards/: remove exports for CPU_FAM
2019-10-18 08:55:33 +02:00
Francisco Molina
f3482de277
REMOVEME: add OS and OS_ARCH variable
2019-10-18 08:46:51 +02:00
Francisco Molina
c010f59b8c
Makefile.include: remove repeated OS declaration
...
- OS := $(shell uname) is already declared in `Makefile.include`
re-declaring it means it will be re-evalauted multiple times
uselessly.
2019-10-18 08:46:51 +02:00
Francisco
01779508d6
Merge pull request #12394 from aabadie/pr/make/iotlab_support_fix
...
make/testbed-support: fix error with FLASHFILE not defined
2019-10-17 23:21:12 +02:00
5873a04ba9
boards/cc2538*: remove useless provided gpio features
...
These features are provided at CPU level
2019-10-17 22:05:42 +02:00
2bf983038d
boards/cc2538*: reorder provided features
2019-10-17 22:04:02 +02:00
27f2a19f72
boards/atmega: remove useless provided gpio features
...
These features are provided at CPU level
2019-10-17 21:42:49 +02:00
Benjamin Valentin
20906328b4
boards/microduino-corerf: Initial board support
2019-10-17 19:20:31 +02:00
Benjamin Valentin
7d78e32b15
cpu/atmega128rfa1: ATmega128rfa1 MCU support
2019-10-17 19:20:31 +02:00
Benjamin Valentin
6617c5c768
cpu/atmega_common: provide dummy implementation for led_init()
2019-10-17 19:20:31 +02:00
Kevin "Tristate Tom" Weiss
0e85425ae4
Merge pull request #12103 from JannesVolkens/mpu9x50
...
driver/mpu9x50: make mpu9150 more generic
2019-10-17 15:01:50 +02:00
Jannes
fdd34499ac
drivers/mpu9x50: Correct read_temperature
...
Change msbiot Makefile.dep back to mpu9150
2019-10-17 14:04:43 +02:00
Jannes
2df5d6048d
driver/mpu9x50: Rename mpu9150 to mpu9x50
...
Rename all files
Rename all variables, methods and methodcalls
Rename all folders
Add to the makefiles
Add to doc
2019-10-17 12:52:18 +02:00
Francisco Molina
0e672da1e4
boards/mulle: remove simple expansion of PORT
2019-10-17 11:17:16 +02:00
4c794c1122
boards/frdm: document more the OpenOCD version requirement
...
Add the need to have a built from source version of OpenOCD for kw41z and give the url of the commit adding the change in OpenOCD
2019-10-16 14:53:42 +02:00
f81baf2bf6
boards/frdm: remove OpenOCD < 0.10 specific code
...
OpenOCD 0.10 is out from early 2017, all stable Linux distros provide this version now.
2019-10-16 14:51:53 +02:00
Frank Hessel
40fe3154b4
boards/native Add SPI feature to doc.txt
2019-10-16 14:33:07 +02:00
