There are STM32 families where all models use only the Synopsys DWC2 USB OTG core while others completely use only the USB Device FS core. For these families then either the driver `drivers/usbdev_synopsys_dwc2` or the driver `cpu/stm32/periph/usbdev` is used depending on the respective family. However, the STM32 families F1 and L4 use both cores. The correct driver must therefore be selected depending on the CPU line or CPU model.
This splits up the clock configs.
It allows CPU_FAM based file sourcing and also common CPU_FAMs.
The dependancies are also included in wildcards would be used for the CPU_FAM macro.
This should be much more readable.
This also takes into account the HSE speeds in order to match the make/header resolution.
Some hidden symbols were added to make sorting many CPU_SERIES dependencies easier.
Make sure the STATUS register has been synced between the different clock domains.
Especially the LETIMER needs some time to update the STATUS register after it has been enabled. If the LETIMER is started and stopped with just a short delay, pm_layered gets confused because the timer seems to be inactive ...
This allows boards to define different crystal frequencies. The correct frequency is required by the system-related methods to ensure proper function of the underlying emlib.
As implmented, dma_resume assumed that transfers widths were 1 byte and
that the memory address incrmenting was always on and periphial address
incrementing always off. This resulted in memory corruption anytime
these assumptions were not true and a dma was resumed. The DMA module
allows intitiating transfers that did not meet these assumption.
This patch adds proper handling inside dma_resume to safely resume any
transfer. Clearifications and errors are added/fixed in the module's
header file. Also, a few constants are removed from the gobal namespace.
As it was, the calculation of DMA2's IRQ number was inccrorect for some
STM families. The implmentation alocates streams numbers 0 to 7 for the
first DMA controller and 8 and up for the second DMA controller. This
offset of +8 was not accounted for when IRQ's of the second DMA
controller was calculated. This patch corrects this.
Use `DWC2_USB_OTG_FS_TOTAL_FIFO_SIZE` instead of `USB_OTG_FS_TOTAL_FIFO_SIZE` since the latter is only defined in the vendor headers for STM32 MCUs. The STM32-specific problem that `USB_OTG_FS_TOTAL_FIFO_SIZE` is not defined in the vendor headers for all STM32 families has therefore been moved from the driver to the STM32-specific USB device header.
The `usbdev_synopsys_dwc2 driver` requires the `ztimer_msec` module and is therefore responsible for pulling it in. Therefore, the dependency on `ztimer_msec` can be removed here.
`thread_stack_init()` didn't correctly set up the stack alignment.
This fixes the issue and brings the function closer to the Cortex M
version, laying the groundwork for future code duplication.
This fixes https://github.com/RIOT-OS/RIOT/issues/11885
There are two schemes for accessing the packet buffer area (PMA) from the CPU:
- 2 x 16 bit/word access scheme where two 16-bit half-words per word can be accessed. With this scheme the access can be half-word aligned and the PMA address offset corresponds therefore to the local USB IP address. The size of the PMA SRAM is usually 1024 byte.
- 1 x 16 bit/word access scheme where one 16-bit half word per word can be accessed. With this scheme the access can only be word-aligned and the PMA address offset to a half-word is therefore twice the local USB IP address. The size of the PMA SRAM is usually 512 byte.
Which access scheme is used depends on the STM32 model.
The addressing of the Packet buffer Memory Area (PMA) is done locally in the USB IP core in half-words with 16-bit. The `_ep_in_buf` and `_ep_out_buf` arrays which hold these USB IP local addresses in the PMA for initialized EPs therefore always use `uint16_t`.
If the MCU does not have an internal D+ pullup and there is no dedicated GPIO to simulate a USB disconnect, the D+ GPIO is temporarily configured as an output and pushed down to simulate a disconnect/connect cycle to allow the host to recognize the device. However, this requires an external pullup on D+ signal to work
If `RCC_CFGR_USBPRE` is defined, the USB device FS clock of 48 MHz is derived from the PLL clock. In this case the PLL clock must be configured and must be either 48 MHz or 72 MHz. If the PLL clock is 72 MHz it is pre-divided by 1.5, the PLL clock of 48 MHz is used directly.
The definition in `pkg/esp32_sdk/Makefile.include` was evaluated by
`make` after the include paths were already set, resulting in
`ESP32_SDK_DIR` being empty in
INCLUDES += -I$(ESP32_SDK_DIR)/components
[...]
This in turn resulted in
cc1: error: /components: No such file or directory [-Werror=missing-include-dirs]
[...]
The parameters for parity and stop bits was confused, resulting in
the following compilation error with GCC 12.2.0:
/home/maribu/Repos/software/RIOT/cpu/esp_common/periph/uart.c: In function '_uart_config':
/home/maribu/Repos/software/RIOT/cpu/esp_common/periph/uart.c:394:61: error: implicit conversion from 'uart_stop_bits_t' to 'uart_parity_t' -Werror=enum-conversion]
394 | if (_uart_set_mode(uart, _uarts[uart].data, _uarts[uart].stop,
| ~~~~~~~~~~~~^~~~~
/home/maribu/Repos/software/RIOT/cpu/esp_common/periph/uart.c:395:42: error: implicit conversion from 'uart_parity_t' to 'uart_stop_bits_t' -Werror=enum-conversion]
395 | _uarts[uart].parity) != UART_OK) {
| ~~~~~~~~~~~~^~~~~~~
cc1: all warnings being treated as errors
This swaps the parameters.
For a number of STM32 MCUs with the USB-FS device interface the signals USB_DP and USB_DM are not defined as GPIO alternative function but as additional function. Additional functions are directly selected/enabled through peripheral registers hand have not to be configured. In this case, the configuration defines GIO_AF_UNDEF as alternative function.
