On samd5x only the RTC can wake the CPU from Deep Sleep (pm modes 0 & 1).
The external interrupt controller is disabled, but we can use the tamper
detection of the RTC.
If an gpio interrupt is configured on one of the five tamper detect pins,
those can be used to wake the CPU from Deep Sleep / Hibernate.
The Cortex-m0 based ATSAM devices can use the Single-cycle I/O Port for
GPIO. This commit modifies the gpio_t type to use this port when
available. It is mapped back to the peripheral memory space for
configuration access. When it is not available, the _port_iobus() and
_port() functions behave identical, which is the case for the samd51.
This changes the prefixes of the symbols generated from USEMODULE and
USEPKG variables. The changes are as follow:
KCONFIG_MODULE_ => KCONFIG_USEMODULE_
KCONFIG_PKG_ => KCONFIG_USEPKG_
MODULE_ => USEMODULE_
PKG_ => USEPKG_
If we disable an external interrupt, GPIO events that would generate an interrupt will still set the interrupt flag.
That means once we enable the interrupt again, a stale interrupt will be triggered.
This is surprising and probably not what the user wants, unfortunately the API documentation is not very clear about what to expect.
There is however no way to drop those intermediate interrupts with the current API.
Ignoring the events that occurred while the GPIO interrupt were disabled is probably the right (and expected) thing to.
Move common code into helper functions and extract the commands
that differ between normal and RWWEE page reading / writing.
This cuts down on `#ifdef` use.
The RTC and RTT share the same peripheral, so they can also
share the same code.
This is needed to integrate the Tamper Detection into common
RTC/RTT code.
We don't need to read-modify-write the CTRLA register to disable
the UART.
The entire CTRLA register is re-written just a few lines below, so
we can just set it to 0 to disable the UART.
There is also no need to reset the UART since we re-write all config
registers in init.
The Atmel I2C peripheral supports arbitrary I2C frequencies.
Since the `i2c_speed_t` enum just encodes the raw frequency values,
we can just use them in the peripheral definition.
We just have to remove the switch-case block that will generate an error
for values outside of `i2c_speed_t`.
Currently only samd21 used the 32 kHz clock for EXTI which makes it miss fast events.
All newer members of the family use the MAIN clock.
While touching this, also make the clock source configurable to this can be overwritten,
e.g. in the board config if desired.
If a write to a full tsrb is attempted with disabled interrupts
or in a interrupt then a deadlock will occure. To avoid this make
space in the ringbuffer by synchronously writing to uart.
The UART TX and TX lines on SAMD5x and SAML1x can be inverted.
However, the flags don't do exactly what one would expect.
See errata 2.18.5: SERCOM-UART: TXINV and RXINV Bits Reference:
> The TXINV and RXINV bits in the CTRLA register have inverted functionality.
>
> Workaround:
> In software interpret the TXINV bit as a functionality of RXINV, and conversely,
> interpret the RXINV bit as a functionality of TXINV.
When the SPI peripheral is disabled, the output lines will become HIGH-Z.
If the clk pin is not pulled HIGH or LOW, connected SPI slaves will start drawing current expectedly.
Writing a 1 bit clears the interrupt flag, writing with |= is thus
uneccecary (and actually an error as this would clear *all* flags).
This cleanup was already done for rtt.c, but rtc.c missed out.
The sam0 MCUs all have a DAC peripheral.
The DAC has a resulution of 10 or 12 bits and can have one or two
output channels.
The output pins are always hard-wired to PA2 for DAC0 and PA5 for DAC1
if it exists.
On the same54-xpro I would only get a max value of ~1V when using the
internal reference, so I configured it to use an external voltage reference.
The external reference pin is hard-wired to PA3, so you'll have to connect
that to 3.3V to get results.
For consistency, use named GCLKs.
- `SAM0_GCLK_32KHZ` will always be 2 for samd21
- `SAM0_GCLK_MAIN` will always be 0
So no change in functionality, just makes the code easier to understand.
bitarithm.h is not needed for the interface of shed but may cause conflicts
due to different definitions of SETBIT and CLRBIT
common implementations are: (value, offset) xor (value, mask) bitarithm
implements the later
frac.c and nrf52/usbdev.c use bitarithm.h but where missing the include
sam0/rtt.c defined a bit using mask from bitarithm,
changed that to the soulution used in sam0/rtc.c
Instead of hard-coding the peripheral clocks to CLOCK_CORECLOCK
introduce helper functions to return the frequency of the individual
GCLKs and use those for baud-rate calculations.
This requires the GCLK to be part of the peripheral's config struct.
While this is already the case for most peripherals, this also adds
it for those where it wasn't used before.
As it defaults to 0 (CLOCK_CORECLOCK) no change is to be expected.
To simplify board definitions and for unification between samd2x and
newer models, don't use the GCLK bitmask in board definitions.
Instead use the GCLK index and generate the bitmask when needed.
The common ADC API dictates that a sample call must return -1 on an
incorrect resolution. The sam0 ADC implementation instead threw an
assertion failure.
