When a timer is set, any pending interrupts must be cleared before the interrupt is enabled for the channel. Otherwise the interrupt would be triggered immediately when the timer is set.
19192: cpu/esp32: fixes for boot issues and crashes on ESP32 r=kaspar030 a=Flole998
### Contribution description
In syscalls_init() there is a call to malloc(), which will return NULL if the heap is not initialized before, causing the entire board to fail booting if MODULE_ESP_IDF_HEAP is used.
API of [vTaskDelete()](https://www.freertos.org/a00126.html) says, that if NULL is passed to vTaskDelete the calling task should be deleted.
This PR needs a backport to 2023.01.
### Testing procedure
Just compiling on the ESP32S2 and running it with WiFi caused it to not start anymore, no output, nothing. When Null is written to that null-pointer it hangs.
The second commit fixed an issue/assertion fail that happens when the WiFi connection drops/disconnects.
### Issues/PRs references
Issue was introduced with PR #19146
Co-authored-by: Flole998 <Flole998@users.noreply.github.com>
In syscalls_init() there is a call to malloc(), which will return NULL if the heap is not initialized before, causing the entire board to fail booting if MODULE_ESP_IDF_HEAP is used.
19185: cpu/gd32v: add periph_gpio_irq support r=gschorcht a=gschorcht
### Contribution description
This PR provides the `periph_gpio_irq` support and is one of a bunch of follow up PRs that complete the peripheral drivers for GD32VF103.
### Testing procedure
Use a GD32VF103 board and flash `tests/periph_gpio`. Note: The Sipeed Longan Nano works also with `seeedstudio-gd32` board defintion and could be used for testing.
```
BOARD=seeedstudio-gd32 make -C tests/periph_gpio flash (until PR #19170 is merged only `seeedstudio
```
With the GPIO PB8 and PB9 connected, the following test sequence should work:
```
> init_out 1 8
> init_int 1 9 2 0
GPIO_PIN(1, 9) successfully initialized as ext int
> set 1 8
INT: external interrupt from pin 9
> clear 1 8
INT: external interrupt from pin 9
```
### Issues/PRs references
19187: cpu/gd32v: add pm_layered support in periph_pm r=gschorcht a=gschorcht
### Contribution description
This PR provides the `pm_layered` support and is one of a bunch of follow up PRs that complete the peripheral drivers for GD32VF103.
Since the configuration of the deep sleep and the standby mode require the access CSR (control and status registers) of the MCU, the Nuclei-SDK NMSIS is added as package which provides a low-level interface for Nuclei-based RISC-V MCUs.
### Testing procedure
The best way to test it is to rebase this PR onto PR #19186 and to flash `tests/periph_pm` to any GD32VF103 board. Note: The Sipeed Longan Nano works also with `seeedstudio-gd32` board definition and could be used for testing.
```
BOARD=seeedstudio-gd32 make -C tests/periph_pm flash
```
The test output should be:
```
main(): This is RIOT! (Version: 2023.04-devel-174-g7dc91-cpu/gd32v/periph_pm_test)
...
mode 0 blockers: 1
mode 1 blockers: 2
mode 2 blockers: 0
Lowest allowed mode: 2
```
Using command the `set_rtc 1 5` command should let the MCU deep sleep for 5 seconds
```
> set_rtc 1 5
Setting power mode 1 for 5 seconds.
␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀>
```
while command `set_rtc 1 5` should set the MCU into the standby mode which is left with restart.
```
> set_rtc 0 5
Setting power mode 0 for 5 seconds.
main(): This is RIOT! (Version: 2023.04-devel-174-g7dc91-cpu/gd32v/periph_pm_test)
...
mode 0 blockers: 1
mode 1 blockers: 2
mode 2 blockers: 0
Lowest allowed mode: 2
>
```
The garbage on UART interface after deep sleep is caused by the clock synchronisation that becomes necessary after deep sleep and is the same as for other boards.
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
18472: drivers/mrf24j40: add support for IEEE 802.15.4 Radio HAL r=benpicco a=jia200x
19175: drivers/periph_common/flashpage: fix silent error r=benpicco a=Enoch247
### Contribution description
This patch removes a test that silently hides failed writes to NULL. Instead, assert is used to ensure that the address is not NULL.
### Testing procedure
I am not certain how to update the tests to catch asserts. If this is possible, I will add a test, if someone will point me to a good example to learn from.
### Issues/PRs references
- none
Co-authored-by: Jose Alamos <jose@alamos.cc>
Co-authored-by: Joshua DeWeese <jdeweese@primecontrols.com>
19079: cpu/esp32: add periph_flashpage support r=kaspar030 a=gschorcht
### Contribution description
This PR provides the `periph_flashpage` support for ESP32x SoCs.
For byte-aligned read access to constant data in the flash, the MMU of all ESP32x SoCs allows to map a certain number of 64 kByte pages of the flash into the data address space of the CPU. This address space is called DROM. Normally the whole DROM address space is assigned to the section `.rodata`. The default flash layout used by all ESP32x SoCs is:
| Address in Flash | Content |
|:-----------------------|:-----------|
| `0x0000` or `0x1000` | bootloader |
| `0x8000` | parition table |
| `0x9000` | `nvs` parition with WiFi data |
| `0xf000` | `phy_init` partition with RF data |
| `0x10000` | `factory` partition with the app image |
The factory partition consists of a number of 64 kByte pages for the sections `.text`, `.rodata`, `.bss` and others. The `.text` and `rodata` sections are page-aligned and are simply mapped into the instruction address space (IROM) and the data address space (DROM), respectively. All other sections are loaded into RAM.
If the `periph_flashpage` module is used, the `periph_flashpage` driver
- decreases the size of the `.rodata` section in DROM address space by `CONFIG_ESP_FLASHPAGE_CAPACITY`,
- adds a section `.flashpage.writable` of size `CONFIG_ESP_FLASHPAGE_CAPACITY` at the end of DROM address space that is mapped into data address space of the CPU,
- reserves a region of size `CONFIG_ESP_FLASHPAGE_CAPACITY` starting from `0x10000` in front of the image partition `factory` and
- moves the image partition `factory` by `CONFIG_ESP_FLASHPAGE_CAPACITY` to address `0x10000 + CONFIG_ESP_FLASHPAGE_CAPACITY`.
The new flash layout is then:
| Address in Flash | Content |
|:-----------------------|:-----------|
| `0x0000` or `0x1000` | bootloader |
| `0x8000` | parition table |
| `0x9000` | `nvs` parition with WiFi data |
| `0xf000` | `phy_init` partition with RF data |
| `0x10000` | flashpage region |
| `0x10000 + CONFIG_ESP_FLASHPAGE_CAPACITY` | `factory` partition with the app image |
This guarantees that the flash pages are not overwritten if a new app image with changed size is flashed. `CONFIG_ESP_FLASHPAGE_CAPACITY` has to be a multiple of 64 kBytes.
~The PR includes PR #19077 and PR #19078 for the moment to be compilable.~
### Testing procedure
The following tests should pass.
```
USEMODULE='esp_log_startup ps shell_cmds_default' BOARD=esp32-wroom-32 make -j8 -C tests/periph_flashpage flash term
```
```
USEMODULE='esp_log_startup ps shell_cmds_default' BOARD=esp32-wroom-32 make -j8 -C tests/mtd_flashpage flash term
```
### Issues/PRs references
Depends on PR #19077
Depends on PR #19078
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19010: bootloaders/riotboot: add tinyUSB DFU support r=benpicco a=gschorcht
### Contribution description
This PR provides
- the tinyUSB DFU and DFU Runtime support and
- the `riotboot_tinyusb_dfu` bootloader that uses the tinyUSB DFU mode to flash new application images.
~This PR includes PR #18983 for now to be compilable.~
### Testing procedure
1. Use any board that supports the `riotboot´ and `tinyusb_device` features and flash the bootloader first, for example
```
BOARD=nucleo-f767zi make -C bootloaders/riotboot_tinyusb_dfu flash
```
and check that the `riotboot_tinyusb_dfu` bootloader is in DFU mode:
```
dfu-util --list
```
3. Flash a first application using the following command:
```
FEATURES_REQUIRED=riotboot USEMODULE=tinyusb_dfu BOARD=nucleo-f767zi \
make -C tests/saul PROGRAMMER=dfu-util riotboot/flash-slot0
```
and check that the application starts and is seen as upgradable:
```
dfu-util --list
```
4. Restart the node in bootloader DFU mode by:
```
dfu-util -e
```
Flash a second application, for example
```
FEATURES_REQUIRED=riotboot USEMODULE=tinyusb_dfu BOARD=nucleo-f767zi \
make -C tests/shell PROGRAMMER=dfu-util riotboot/flash-slot1
```
and check that the second application starts and is seen as upgradable:
```
dfu-util --list
```
### Issues/PRs references
~Depends on PR #18983~
19149: SECURITY: Describe that declassification is an option r=benpicco a=chrysn
### Contribution description
Our security policy does not contain provisions for the case when what is reported is not what we consider an actual security issue. As it is described now, everything reported through security@ would go through the full treatment, including a point release.
I'm not sure it belongs into the text itself (as it's more about how security reporters interact with the project than internals), but declassification should IMO be backed at least by 3 maintainers, and no strong NACK.
### Issues/PRs references
#19141 followed that procedure after some chat on it on the maintainers channel. (In the discussion, I proposed declassification, with 2.5 people supporting it and one "I was about to, but can we be sure nobody is using it?" voice).
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: chrysn <chrysn@fsfe.org>
18763: sys/tiny_strerror: add missing error codes r=benpicco a=maribu
### Contribution description
When double-checking the error codes provided by newlib by default (without magic defines, such as `__LINUX_ERRNO_EXTENSIONS__` or `__CYGWIN__`), some where still missing in `tiny_strerror()`. This adds the missing ones.
This in turn showed that three errno codes were missing in the avr-libc compat `errno.h`, which are added as well.
### Testing procedure
Murdock should double check that the added errno codes indeed are defined by default.
### Issues/PRs references
None
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
To avoid garbage on reconfiguring the UART console pins, e.g. in initialization of the `arduino` module, pins that are already configured as UART pins must not be initialized.
The TX line is set and temporarily configured as a pull-up open-drain output before configuring it as a push-pull output to avoid a several msec long LOW pulse resulting in some garbage.
Since PR #19100 it is possible to define:
- other pins for `UART_DEV(0)` than the default pins
- different `UART_DEV(0)` pins for the bootloader and RIOT
To allow correct reinitialization of the UART pins used by the bootloader as well as their usage for other purposes, the pin usage for the default UART0 pins and the UART pins used by the bootloader are reset to `_GPIO`. This is done in `uart_system_init` which has to be called earlier in the startup procedure.
If LOG_LEVEL >= 4, such as in `tests/log_printfnoformat`, the ESP-IDF config function called for the GPIO pins of the UART will output the configuration with `printf` before the `_GLOBAL_REENT` structure is initialized. This causes a crash during system startup. Therefore the initialization by `syscalls_init` must be called earlier in the startup procedure.
19050: boards/common/cc26xx cc13xx: clean up and fix flash configs r=benpicco a=maribu
### Contribution description
- Add support for XDS110 debugger via `OPENOCD_DEBUG_ADAPTER=xds110`
- Clean up OpenOCD configs in `boards/common/cc26xx_cc13xx`
- No longer hardcode the debugger to xds110, but use `OPENOCD_DEBUG_ADATER ?= xds110`
- Add support for cc13x0, cc13x2, cc26x0
- `boards/cc2650*`: drop custom OpenOCD config in favor of shared one
- add variables needed to support flashing with `PROGRAMMER=jlink`
- allow specifying a custom OpenOCD command to bring the device to a halt state, as the default `reset halt` (which causes a second reset) is causing issues with the ICEPick JTAG routers in the CC26xx - CC13xx devices
- Use `halt` instead of `reset halt` for CC26xx / CC13xx boards in OpenOCD to avoid issues in flashing
### Testing procedure
```
make BOARD=cc2650-launchpad -C examples/default flash
```
Should now work. The same should still work for other cc26xx cc13xx boards.
### Issues/PRs references
Partially fixes: https://github.com/RIOT-OS/RIOT/issues/18750
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
19109: cpu/gd32v: fix and extend Kconfig clock settings r=benpicco a=gschorcht
### Contribution description
This PR fixes the following issus of the clock configuration which led to highly deviating peripheral clocks so that the UART interface was not usable in my case:
1. Setting the `RCU_CTL` register just to the IRC8M bit also removes the IRC8M calibration and trim adjust value in this register. Therefore IRC8M calibration and trim adjust value have to be preserved and the IRC8M has to be set.
2. `CLOCK_HXTAL` is a value and not a flag, so that shifting to the left changes anything in the register but does not set the PLLSEL bit. `RCU_CFG0_PLLSEL_Msk` has to be used instead to set the PLLSEL bit.
3. `CONFIG_BOARD_HAS_HXTAL` is used to indicate that the board has an HXTAL connected. If the HXTAL is present, it is used as PLL clock source. But if the HXTAL is not present, the half IRC8M clock should be used as PLL clock source and must not be disabled at the end of clock settings. Using IRC8M clock as PLL clock source also requires another PLL multiplication factor.
Issues 1 and 2 led to the problem that IRC8M was used without calibration instead of HXTAL. With the fixes, the GD32V is working with as well as without HXTAL correctly.
Furthermore, the Kconfig configuration has been extended. It is now possible to configure the HXTAL frequency as well, since the GD32VF103 allows HXTAL clocks from 3 MHz to 25 MHz. This has currently been added directly to the board's Kconfig, as it is currently the only GD32VF103 board. It should be moved to a common Kconfig later when more GD32V boards are added.
### Testing procedure
`BOARD=seeedstudio-gd32 make -C tests/shell flash term` should still work.
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
The configuration whether a HXTAL is present and what its clock frequency is will be added to Kconfig. Since it is the only GD32V board at the moment, the configuration is added to the Kconfig of the board, but should be moved to a common Kconfig later when more GD32V boards are added.
`CONFIG_BOARD_HAS_HXTAL` is used to indicate that the board has an HXTAL connected. If the HXTAL is present, it is used as PLL clock source. But if the HXTAL is not present, the half IRC8M clock should be used as PLL clock source and must not be disabled at the end of clock settings. Using IRC8M clock as PLL clock source also requires another PLL multiplication factor.
