This commit optimizes the `gpio_conf_t` type in the following
regards:
- The "base" `gpio_conf_t` is stripped from members that only some
platforms support, e.g. drive strength, slew rate, and disabling of
the Schmitt Trigger are no longer universally available but
platform-specific extensions
- The `gpio_conf_t` is now crammed into a bit-field that is 8 bit or
16 bit wide. This allows for storing lots of them e.g. in
`driver_foo_params_t` or `uart_conf_t` etc.
- A `union` of the `struct` with bit-field members and a `bits` is used
to allow accessing all bits in a simple C statement and to ensure
alignment for efficient handling of the type
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
The function configures additional features of the DMA stream for F2/F4/F7.
`dma_setup_ext` added to configure F2/F4/F7 specific additional features like `MBURST`, `PBURST`, `FIFO` and Peripheral flow controller. It is supposed to be used after `dma_setup` and `dma_prepare`.
The `SWJ_CFG` field of the `AFIO_MAPR` register is write only and values
read are undefined (random). Hence, using `AFIO->MAPR |= mask;` to
enable flags can corrupt the state of the `SWJ_CFG` (configure it to
an unintended value).
Two helper functions have been introduced:
- `afio_mapr_read()` reads the value, but sanitizes the `SWJ_CFG` field
to zero
- `afio_mapr_write()` writes the given value, but applies the `SWJ_CFG`
configured by the board before writing.
Finally, the `nucleo-f103rb` and `bluepill*`/`blackpill*` boards have
been updated to no longer specify `STM32F1_DISABLE_JTAG`, as this
is handled by the `SWJ_CFG` setting (which defaults to disabling JTAG).
The assumption that all STM32 timers have exactly four channels no
longer holds. E.g. the STM32L4 has the following general purpose timers:
- TIM2: 32 bit, 4 channels
- TIM15: 16 bit, 2 channels
- TIM16: 16 bit, 1 channel
Hence, a new field is added to the timer configuration to also contain
the number of timer channels. Due to alignment the `struct` previously
was padded by 16 bit, so adding another 8 bit field doesn't increase
its size.
For backward compatibility, a value of `0` is considered as alias for
`TIMER_CHANNEL_NUMOF` (or 4), so that the number of timer channels
only needs to be set when the timer is different from the typical 4
channel timer. This helps backward compatibility.
19628: Fix periph clk r=aabadie a=Enoch247
### Contribution description
This fixes some minor doc and argument type errors. See commit messages for details.
### Testing procedure
It compiles without errors for me.
### Issues/PRs references
None known
19637: sys/usb/usbus_msc: fix typo in C expression r=aabadie a=maribu
### Contribution description
Rather than setting the correct blk_len, the code only wrote 1 and 0 into the three bytes due to the use of a logic and where a bitwise and should be used.
Co-authored-by: Joshua DeWeese <jdeweese@primecontrols.com>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
19572: cpu/stm32/periph_pwm: support of complementary timer outputs r=maribu a=gschorcht
### Contribution description
This PR provides the support of complementary timer outputs as PWM channels for advanced timers (TIM1/TIM8).
To use a complementary output of an advanced timer as PWM channel, the output is defined with an offset of 4, i.e. normal outputs are in the range of 0 to 3 (CH1...CH4) and complementary outputs are in the range of 4 to 6 (CH1N...CH3N). If the defined output is less than 4, the normal output is enabled, otherwise the complementary output is enabled.
This change is required to support PWM on boards that have connected the complementary outputs of advanced timers to the PWM connector pins, for example the STM32L496-DISCO board.
### Testing procedure
- Green CI
- Use any STM32 board which supports the `periph_pwm` feature. `tests/periph_pwm` should still work.
- Change the configuration for this board so that either timer TIM1 or TIM8 and a complementary channel is used for any exposed GPIO. `tests/periph_pwm` should also work with such a configuration.
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
As implmented, dma_resume assumed that transfers widths were 1 byte and
that the memory address incrmenting was always on and periphial address
incrementing always off. This resulted in memory corruption anytime
these assumptions were not true and a dma was resumed. The DMA module
allows intitiating transfers that did not meet these assumption.
This patch adds proper handling inside dma_resume to safely resume any
transfer. Clearifications and errors are added/fixed in the module's
header file. Also, a few constants are removed from the gobal namespace.
As it was, the calculation of DMA2's IRQ number was inccrorect for some
STM families. The implmentation alocates streams numbers 0 to 7 for the
first DMA controller and 8 and up for the second DMA controller. This
offset of +8 was not accounted for when IRQ's of the second DMA
controller was calculated. This patch corrects this.
