Vincent Dupont
4647659ea8
boards: fix CLOCK_PLL_PREDIV on stm32f1xx boards
2020-03-09 18:00:48 +01:00
Leandro Lanzieri
ab10b33848
boards/esp32-wroom-32/doc: Add SPI freq configuration for mrf24j40
2020-03-09 16:51:35 +01:00
Leandro Lanzieri
cffc9b70bf
boards/esp32-wroom-32: Remove drivers configuration from Makefile.dep
...
This removes the configuration parameters for mrf24j40 and enc28j60
drivers, which were present in the boards's Makefile.dep. There is
already documentation regarding how to correctly configure these devices
for the board.
2020-03-09 16:49:11 +01:00
2ec09ebd74
boards/nrf52: remove useless export of FLASH_TARGET_TYPE
2020-03-08 15:12:44 +01:00
Marian Buschsieweke
8fd8c8273f
boards/{nucleo-f103rb,b*pill}: Expose JTAG pins as GPIOs
...
The Nucleo-F103RB comes with an internal SWD programmer/debugger. Thus, the JTAG
pins are not going to be used for debugging / programming anyway. The pins are
exposed on the headers, so allowing them to be used as GPIOs make a lot of
sense.
The Bluepill / Blackpill boards only expose the SWD pins on the debug header,
but the JTAG pins (not also used by SWD) are exposed on the GPIO pin headers.
Hence, exposing them as regular GPIOs seems to be a reasonable choice.
2020-03-08 13:06:34 +01:00
3e97c01c33
thingy52: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:42 +01:00
74022a4bb8
ruuvitag: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:42 +01:00
0573db8a85
reel: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:42 +01:00
bef16095df
pinetime: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:42 +01:00
cbd3c1c643
particle-*: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:42 +01:00
822590ad56
nrf52840-mdk: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:41 +01:00
87b2aa5ed9
nrf52832-mdk: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:41 +01:00
71589a11ec
nrf51dk: Enable the nRF51 built-in DC/DC converter
2020-03-07 17:37:41 +01:00
bea3f71f91
nrf52xxxdk: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:41 +01:00
ec2a3d33c8
acd52832: Enable the nRF52 built-in DC/DC converter
2020-03-07 17:37:41 +01:00
benpicco
7396d05605
Merge pull request #13575 from fjmolinas/pr_cc2538_rf_deps
...
cpu/cc2538: handle cc2538_rf deps in Makefile.dep
2020-03-06 18:00:51 +01:00
Francisco Molina
80ecac5fde
boards: use cc2538_rf as netdev_default for CPU=cc2538
2020-03-06 14:17:52 +01:00
Francisco Molina
ff6f6618fb
cpu/cc2538: handle cc2538_rf deps in Makefile.dep
2020-03-06 14:17:19 +01:00
Benjamin Valentin
ed4d871835
dist/tools/cc2538-bsl: use upstream version
...
Automatically fetch the upstream version of cc2538-bsl.py instead
of maintaining our own fork of the tool.
fixes #13566
2020-03-06 11:13:21 +01:00
ed316309c8
Merge pull request #11874 from kaspar030/ztimer
...
sys/ztimer: initial import
2020-03-06 09:46:27 +01:00
benpicco
681678e3f3
Merge pull request #13537 from jue89/feature/sam0-spi-frequency
...
cpu/sam0_common: mitigate rounding errors of SPI baud rate calculation
2020-03-04 16:50:46 +01:00
f49e756436
boards/ek-lm4f120xl: add ztimer config, increase ztimer_usec_min
2020-03-04 12:44:03 +01:00
a2c0823063
boards/native: add ztimer configuration
2020-03-04 12:44:03 +01:00
84365e326a
boards/*-kw41z: add ztimer_msec config
2020-03-04 12:44:03 +01:00
73adecc02d
boards/samr21-xpro: add ztimer config
2020-03-04 12:44:03 +01:00
eafba65911
boards/common/arduino-atmega: add ztimer configuration
2020-03-04 12:44:03 +01:00
Koos
24b9b99fee
boards/stm32f3discovery: Updated broken image link
2020-03-04 09:54:36 +01:00
Koos
f970f67785
boards/sodaq-sara-aff: Updated broken image link
2020-03-04 09:54:36 +01:00
Koos
ed2ea24405
boards/sodaq-autonomo: Updated broken image link
2020-03-04 09:54:36 +01:00
Koos
2a253ed175
boards/saml11-xpro: Updated broken image link
2020-03-04 09:54:36 +01:00
Koos
8219685be1
boards/nrf52840-mdk: Updated broken image link
2020-03-04 09:54:36 +01:00
Koos
6dd8b2deac
boards/frdm-k64f: Updated broken image link
2020-03-04 09:54:36 +01:00
Koos
cec9817b2e
boards/arduino-mega2560: Updated broken image link
2020-03-04 09:54:36 +01:00
benpicco
7792f91ddc
Merge pull request #13535 from btcven/2020_03_02-cc1312-openocd
...
boards/cc1312-launchpad: add OpenOCD configuration
2020-03-04 00:26:14 +01:00
Jean Pierre Dudey
6e77d9194b
boards/cc1352-launchpad: enable OpenOCD
...
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-03-03 13:42:33 -05:00
Jean Pierre Dudey
ca2e2a4289
boards/cc1312-launchpad: add OpenOCD configuration
...
This enables OpenOCD for the CC1312 LaunchPad.
All we need is:
- The Texas Instruments version of OpenOCD
(https://git.ti.com/cgit/sdo-emu/openocd )
- Set the `PROGRAMMER` environment variable to `openocd`.
- Connect a cc1312-launchpad and play with the commands.
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-03-03 13:42:29 -05:00
Martine Lenders
e4f27b415e
Merge pull request #13394 from benpicco/atmega-rtc
...
cpu/atmega_common: implement emulated RTC support
2020-03-03 19:03:47 +01:00
95d607b54d
Merge pull request #13480 from aabadie/pr/tools/openocd_export_variables
...
tools/openocd: export configuration variables only to required targets
2020-03-03 18:16:05 +01:00
Benjamin Valentin
1dd260b446
boards: enable RTC for every ATmega board that supports RTT
...
Every ATmega board that can run an Real Time Timer can also run
an emulated Real Time Clock.
Got all supported boards by adding `FEATURES_REQUIRED += arch_8bit`
to `tests/periph_rtt` and running
sed -i 's/FEATURES_PROVIDED += periph_rtt/
FEATURES_PROVIDED += periph_rtc\n
FEATURES_PROVIDED += periph_rtt/g'
on them.
2020-03-03 16:27:44 +01:00
26222d601c
boards/arduino-mkr: don't export MKR_JLINK_DEVICE variables
2020-03-03 14:18:03 +01:00
d10211b7ff
boards/esp32-wroom-32: don't export _PARAM_DEFINED variables
2020-03-03 14:18:03 +01:00
a8b81adbd2
boards/cc2650*: don't export XDEBUGGER variable
2020-03-03 14:18:03 +01:00
21f48af3cd
boards/nz32-sc151: don't export ID variable
2020-03-03 14:18:03 +01:00
2722869dbb
boards/arduino-due: don't export BOSSA_ARDUINO_PREFLASH
2020-03-03 14:18:03 +01:00
acce5e22d1
boards/pic32: don't export APPDEPS
...
This variable is already export in vars.inc.mk
2020-03-03 14:18:03 +01:00
cc48b67fb5
boards/pic32: don't export USE_UHI_SYSCALLS
2020-03-03 14:18:03 +01:00
b7f5b18991
boards: don't export ROM_OFFSET variable
2020-03-03 14:18:03 +01:00
bd81060354
boards/{telosb,iotlab}: remove useless export for BAUD
...
The variable is already eported in serial.inc.mk
2020-03-03 14:18:03 +01:00
Francisco
3f062a78b2
Merge pull request #13045 from aabadie/pr/boards/remote_factorize
...
boards/remote*: cleanup and factorize code in peripheral configuration headers
2020-03-03 13:21:04 +01:00
481f3bcb35
Merge pull request #13180 from fjmolinas/pr_slwstk6000b_cleanup
...
boards/slwstk6000b-*: cleanup
2020-03-03 13:15:03 +01:00
Juergen Fitschen
8fbfb13c84
Revert "boards/samr30-xpro: fix AT86RF212B communication"
...
This reverts commit a9faac7218
2020-03-03 12:32:54 +01:00
d13d1aed48
Merge pull request #13336 from bergzand/pr/mtd_spi_nor/erase_timings_in_struct
...
mtd_spi_nor: erase timings in struct
2020-03-03 11:59:28 +01:00
f1ba22534a
boards: don't export globally OPENOCD_RESET_USE...
2020-03-03 11:42:19 +01:00
Francisco Molina
86ed76fec0
boards/common/slwstk6000b: remove unused files
2020-03-03 11:24:28 +01:00
Francisco Molina
e951b720b8
boards/common/slwstk6000b: use slwstk6000b.vars.mk to parse JLINK_DEVICE
2020-03-03 11:24:27 +01:00
Francisco Molina
22aae93efb
boards/common/slwstk6000b: cleanup slwrb41* includes
2020-03-03 11:24:26 +01:00
Francisco Molina
b7783e67a8
boards/common/slwstk6000b: use slwstk6000b.vars.mk to parse CPU_MODEL
2020-03-03 11:24:26 +01:00
Francisco Molina
96cfa1d41c
boards/common/slwstk6000b: add module variables makefile
2020-03-03 11:22:48 +01:00
8931889865
pinetime: add erase timings to mtd_spi_nor instance
2020-03-03 09:49:08 +01:00
dcdaf8a2ab
mulle: add erase timings to mtd_spi_nor instance
2020-03-03 09:49:08 +01:00
Juergen Fitschen
a9faac7218
boards/samr30-xpro: fix AT86RF212B communication
...
This board is driven by a 16MHz clock source. In this case, the baud rate generator is able to clock the SPI interface with 4MHz or 8MHz only.
Due to integer division and rounding, the interface is actually driven with 8MHz, which is too fast for the AT86RF212.
2020-03-02 18:38:04 +01:00
Francisco
5af4c5a9c5
Merge pull request #13470 from kfessel/fix13179
...
boards/nucleo-f767zi: Fix13179 make nucleo-f767zi debuggable again
2020-02-28 17:42:10 +01:00
benpicco
2ebf1d68b4
Merge pull request #13497 from benpicco/openmote-b-fixes
...
boards/openmote-b: add saul config, add note about flashing
2020-02-28 14:59:25 +01:00
Karl Fessel
979b4d5cf7
Revert "boards/nucleo-f767zi: add correct flash bank openocd config"
...
This reverts commits:
- 1dec5ba61b53f60db66f
2020-02-28 13:51:58 +01:00
Benjamin Valentin
961b333ea6
boards/openmote-b: add saul config
...
Hook up the GPIOs and the si7006 sensor to SAUL.
2020-02-28 13:37:15 +01:00
Benjamin Valentin
bf96e97e34
boards/openmote-b: extend doc.txt about flashing
...
To flash the board the intelhex python package needs to be installed.
Add a note about it to the documentation.
2020-02-28 13:37:15 +01:00
benpicco
23c5d34284
Merge pull request #10846 from benemorius/kw41z-mini
...
boards: add support for kw41z-mini
2020-02-28 07:40:25 +01:00
Thomas Stilwell
ef6024cf1a
boards: add kw41z-mini
2020-02-27 21:34:04 -06:00
Benjamin Valentin
9d1a2b5fb4
boards/mcb2388: add I2C config
...
The pins for I2C0 and I2C1 are available on the board,
nothing is wired up to them.
2020-02-26 23:41:38 +01:00
Benjamin Valentin
4d5d3eb9e6
boards/msba2: hook up i2c
...
I2C is not used by any chip on the board, but I2C2 is availiable
on the JP3 connector (shared with UART2).
- SDA: P0.10
- SCL: P0.11
2020-02-26 23:41:38 +01:00
cbb248319e
boards/pinetime: update mtd_spi_nor config
2020-02-26 10:00:55 +01:00
2dcf65d942
Merge pull request #13332 from bergzand/pr/mtd_spi_nor/params_struct
...
mtd_spi_nor: Move const params to separate struct
2020-02-26 09:43:18 +01:00
Peter Kietzmann
a27b58fbba
Merge pull request #13479 from MichelRottleuthner/pr_phytec_fix_tmp_addr
...
boards/pba-d-01-kw2x: add config for tmp006 addr
2020-02-25 21:04:20 +01:00
a8231f2079
Merge pull request #13161 from bergzand/pr/pinetime/mtd
...
pinetime: add MTD configuration
2020-02-25 20:44:59 +01:00
Michel Rottleuthner
9ec1a6fab5
boards/pba-d-01-kw2x: add config for tmp006 addr
2020-02-25 20:25:26 +01:00
benpicco
aa1c23d4bd
Merge pull request #11929 from fabian18/driver-at24cxxx-eeprom
...
Driver for AT24CXXX EEPROM
2020-02-25 18:16:45 +01:00
0d468c1068
boards/common/silabs: remove OPENOCD_CONFIG export
2020-02-25 17:26:00 +01:00
f451eb692c
Merge pull request #13452 from aabadie/pr/tools/openocd_config_export
...
tools/openocd: only export OPENOCD_CONFIG to required targets
2020-02-25 15:11:38 +01:00
514873fe12
pinetime: add MTD configuration
2020-02-25 14:31:39 +01:00
785052e410
Merge pull request #13468 from aabadie/pr/tools/bossa_rework
...
tools/bossa: split between 1.8 and 1.9 versions
2020-02-25 13:32:38 +01:00
d41621e95f
boards/arduino-due: force bossa 1.8 version
2020-02-25 11:49:10 +01:00
fe8c242a30
boards/native: remove exports of UNDEF vars
2020-02-25 09:40:34 +01:00
benpicco
77d6eaaf19
Merge pull request #13461 from benpicco/sam_xpro-led-fix
...
boards/samXXX-xpro: clear LED on init
2020-02-24 21:56:36 +01:00
Benjamin Valentin
bc5ac92cff
boards/samXXX-xpro: clear LED on init
...
The LED on the sam-xpro boards is active low, so we have
to turn it off manually, otherwise it's always on.
2020-02-24 19:44:36 +01:00
benpicco
4671fd2fe4
Merge pull request #10475 from chrysn-pull-requests/openocd-for-stk3700
...
boards/any silabs: Allow selecting OpenOCD
2020-02-24 19:12:43 +01:00
fabian18
07f7d818bd
boards/same54-xpro: use at24cxxx EEPROM
2020-02-24 14:00:25 +01:00
9363f077d6
boards: don't export globally OPENOCD_CONFIG
...
The variable is already exported to required target in openocd.inc.mk
2020-02-24 10:04:11 +01:00
bd081cd980
tools/openocd: remove default OPENOCD_CONFIG value
...
The default value is already set in openocd.inc.mk
2020-02-24 10:04:11 +01:00
d7cbfe4f45
Merge pull request #13378 from francois-berder/nucleo-doc-cleanup
...
boards: nucleo*: Cleanup documentation
2020-02-24 08:01:42 +01:00
Jean Pierre Dudey
130467dd91
cc1312-launchpad: add board documentation
...
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-02-22 12:43:11 -05:00
benpicco
ce947b4824
Merge pull request #12955 from gschorcht/cpu/esp/deduplicate_and_cleanup
...
cpu/esp*: code deduplication and cleanup
2020-02-22 13:03:18 +01:00
benpicco
261ede7b79
Merge pull request #13414 from benpicco/boards/same54-xpro/peripheral-clocks
...
boards/same54-xpro: don't source peripheral clocks from main clock
2020-02-21 23:25:22 +01:00
benpicco
8d77ec55ae
Merge pull request #13409 from aabadie/pr/cpu/nrf_gpio_t
...
cpu/nrf5x: provide gpio_t type definition
2020-02-21 18:55:46 +01:00
Martine Lenders
4be4f5ad0a
boards/native: add deprecation warnings for make all-debug
2020-02-21 12:51:41 +01:00
Martine Lenders
1786a8353a
boards/native: remove now unnecessary -g3 CFLAGS
...
dbd865413c
2020-02-21 12:50:02 +01:00
benpicco
ea24d30e7a
Merge pull request #13417 from gschorcht/boards/esp32/doc_remove_mcu_table
...
boards/esp32: remove MCU feature table in board documentation
2020-02-21 10:13:44 +01:00
Gunar Schorcht
d251ffd205
boards/esp8266: enable arduino feature
2020-02-21 09:09:34 +01:00
Gunar Schorcht
51200364da
boards/esp8266: fix ARDUINO_LED definitions
...
ARDUINO_LED specifies the according Arduino pin to which the LED is connected and not the GPIO.
2020-02-21 09:09:34 +01:00
Cenk Gündoğan
86fcc35994
Merge pull request #13423 from kaspar030/turn_on_native_debug
...
native: turn on creation of debug symbols (CFLAGS += -g)
2020-02-20 18:20:11 +01:00
dbd865413c
native: turn on creation of debug symbols (CFLAGS += -g)
2020-02-20 17:06:56 +01:00
e324b22c96
Merge pull request #13418 from gschorcht/boards/esp32/fix_btn0_pin
...
boards/esp32: rename BUTTON0_PIN to BTN0_PIN
2020-02-20 14:40:39 +01:00
Gunar Schorcht
6a7ba7ba1a
boards/esp32: rename BUTTON0_PIN to BTN0_PIN
...
Since a number of applications rely on the existence of the BTN0_PIN definition, the BUTTON0_PIN definition has been renamed to BTN0_PIN to make the ESP32 boards compatible with these applications. However, for compatibility with earlier versions, BUTTON0_PIN is still defined as an alias of BTN0_PIN.
2020-02-20 12:14:44 +01:00
Gunar Schorcht
e4b3ce7c91
boards/esp32: remove MCU feature table in doc
...
Instead of using the same MCU feature table in every board documentation, it refers to the MCU documentation. This makes it easier to maintain the MCU feature table.
2020-02-20 08:47:18 +01:00
6182e7c977
boards/nrf52: remove uint8_t cast for GPIO_UNDEF
2020-02-19 19:16:58 +01:00
Benjamin Valentin
3ee7b72431
boards/same54-xpro: don't source peripheral clocks from main clock
...
Use the dedicated 48 MHz clock as a source for the peripheral clocks.
This was already done for I2C to allow it to work despite the 120 MHz
main clock.
Not running the peripherals off the main clock will allow for dynamic
re-clocking of the main clock in the future, without affecting the
operation of the peripherals.
It also gives more flexibility to the main clock selection in general.
2020-02-19 17:52:12 +01:00
Sebastian Meiling
85c01f2ebd
boards: update supported features of pba-d-01-kw2x
2020-02-18 11:42:05 +01:00
Sebastian Meiling
867090c579
boards: update links in doc of pba-d-01-kw2x
2020-02-18 11:40:34 +01:00
Sebastian Meiling
a9cb3b637f
boards: add pinout ref for pba-d-01-kw2x
2020-02-18 11:40:34 +01:00
Yegor Yefremov
5cd205dffd
boards/esp32-ttgo-t-beam: correct SX127x chip frequencies
...
According to the datasheet, SX1278 covers frequencies till 525MHz
and hence, cannot be used for the 868/915 MHz band. So swap both
chips.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2020-02-17 10:15:40 +01:00
chrysn
f4b1d60887
boards/*silabs: Move programmer selection to common
...
This removes duplication for the jlink case (keeping only any
non-default values in the board makefiles), and opens up STK3700's
OpenOCD programmability for generic boards.
2020-02-14 09:42:20 +01:00
chrysn
80167b8ba4
boards/stk3700: Use OpenOCD-shipped board file
2020-02-14 09:29:32 +01:00
chrysn
4387739494
boards/stk3700: Allow selecting OpenOCD
...
OpenOCD works well with those devices; the OpenOCD config is provided at
the default location and only needs to refer to the setup that OpenOCD
ships.
2020-02-14 08:56:27 +01:00
Francois Berder
99142b170c
boards: nucleo-l152re: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:43:20 +00:00
Francois Berder
7222f42c86
boards: nucleo-f446ze: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:42:49 +00:00
Francois Berder
343f39174e
boards: nucleo-f446re: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:42:20 +00:00
Francois Berder
a42b5d79ab
boards: nucleo-f411re: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:41:13 +00:00
Francois Berder
8f766d594e
boards: nucleo-f410rb: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:40:48 +00:00
Francois Berder
5b81034fa1
boards: nucleo-f401re: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:39:39 +00:00
Francois Berder
1b27d5cb9a
boards: nucleo-f334r8: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:39:11 +00:00
Francois Berder
6fb2275452
boards: nucleo-f303ze: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:38:40 +00:00
Francois Berder
a8cec40371
boards: nucleo-f303re: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:38:15 +00:00
Francois Berder
3739d81aad
boards: nucleo-f303k8: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:37:32 +00:00
Francois Berder
b475598cb8
boards: nucleo-f302r8: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:36:34 +00:00
Francois Berder
d28fb30797
boards: nucleo-f207zg: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:35:54 +00:00
Francois Berder
2cb858c72b
boards: nucleo-f103rb: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:35:21 +00:00
Francois Berder
3e22a77bf0
boards: nucleo-f091rc: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:34:45 +00:00
Francois Berder
7145e56e74
boards: nucleo-f072rb: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:34:03 +00:00
Francois Berder
7c9bbf5d9b
boards: nucleo-f070rb: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:33:46 +00:00
Francois Berder
43a475fef8
boards: nucleo-f030r8: Cleanup documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-13 19:32:50 +00:00
Benjamin Valentin
02e1c0a4ed
boards/same54-xpro: add configuration for AT24MAC402
2020-02-13 15:58:43 +01:00
Benjamin Valentin
59ca6a9b37
boards/avr-rss2: add configuration for AT24MAC602
2020-02-13 15:58:43 +01:00
Bas Stottelaar
3141e91380
Merge pull request #13174 from fjmolinas/pr_efm32_cleanup
...
cpu/efm32: cleanup
2020-02-12 22:42:10 +01:00
Dylan Laduranty
a2d63070ae
Merge pull request #13347 from francois-berder/boards-fpu
...
boards: Fix presence of FPU
2020-02-12 09:12:57 +01:00
Bas Stottelaar
d6b478f607
boards/efm32: provide CPU_FAM
2020-02-11 22:46:17 +01:00
3ac25c3ac9
Merge pull request #12556 from bergzand/wip/stusbdev
...
stm32_common: Add USB OTG FS/HS usbdev peripheral driver
2020-02-11 20:39:46 +01:00
Francois Berder
c76f0e1489
boards: Fix presence of FPU
...
Cortex-M0, Cortex-M0+ and Cortex-M3 MCU never have a FPU.
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-11 18:30:29 +00:00
d40ccc2d6f
mulle: Adapt to separate mtd_spi_nor params
2020-02-11 15:55:41 +01:00
1f5340c307
boards/stm32: Add default config for USB OTG HS peripheral
2020-02-11 15:50:22 +01:00
7f1325e48c
pyboard: add usbdev feature
2020-02-11 15:50:22 +01:00
08c74db3d9
stm32f769i-disco: add usbdev feature
2020-02-11 15:50:21 +01:00
033cb5559a
stm32f723e-disco: add usbdev feature
2020-02-11 15:50:21 +01:00
d9837182a0
stm32f4discovery: add usbdev feature
2020-02-11 15:50:21 +01:00
4d0f3d0d3a
stm32f429i-disc1: add usbdev feature
2020-02-11 15:50:20 +01:00
8198c52d17
nucleo-f767zi: add usbdev feature
2020-02-11 15:50:20 +01:00
befac12f9a
nucleo-f746zg: add usbdev feature
2020-02-11 15:50:20 +01:00
dca64d4120
nucleo-f722ze: add usbdev feature
2020-02-11 15:50:20 +01:00
0f885b3789
nucleo-f446ze: add usbdev feature
2020-02-11 15:50:19 +01:00
625698a1d2
nucleo-f429zi: add usbdev feature
2020-02-11 15:50:19 +01:00
2c6f0537df
nucleo-f413zh: add usbdev feature
2020-02-11 15:50:19 +01:00
f37b5d7ec7
nucleo-f412zg: add usbdev feature
2020-02-11 15:50:18 +01:00
3280248e89
nucleo-f207zg: add usbdev feature
2020-02-11 15:50:18 +01:00
fc63fb77bf
boards/stm32: Add default config for USB OTG FS peripheral
2020-02-11 15:50:18 +01:00
benpicco
33291ad675
Merge pull request #13306 from fjmolinas/pr_samr21_use_xosc
...
boards/sam[r/d]21-xpro: prefer XOSC32K for RTC/RTT (GCLK2)
2020-02-11 15:18:36 +01:00
benpicco
d8c050943c
Merge pull request #13327 from maribu/atmega-bootloader
...
boards: Cleaned up bootloader selection for ATmega
2020-02-10 23:18:43 +01:00
benpicco
82134ad77a
Merge pull request #13323 from francois-berder/mbedlpc1768-doc
...
boards: mbed_lpc1768: Improve documentation
2020-02-10 23:07:27 +01:00
Marian Buschsieweke
fec0f8dd48
boards/waspmote-pro: Refactor avrdude conf
2020-02-10 21:48:03 +01:00
Marian Buschsieweke
21b37a3f5e
boards/mega-xplained: Refactor avrdude conf
2020-02-10 21:48:03 +01:00
Marian Buschsieweke
ff53159f0e
boards/atmega256rfr2-xpro: Refactor avrdude conf
...
- No longer include `tools/serial.mk` and `tools/avrdude.mk`, as this is
no done by `boards/common/atmega`
- No longer provide `RESET ?=`, as this is now done in `tools/avrdude.mk` for
all ATmega boards unless they are using a bootloader
2020-02-10 21:48:03 +01:00
Marian Buschsieweke
26b4da2db2
boards/avr-rss2: Refactor avrdude conf
2020-02-10 21:48:03 +01:00
Marian Buschsieweke
e042bb43e1
boards/derfmega*: Refactor avrdude conf
2020-02-10 21:48:03 +01:00
Francois Berder
056c1e568c
boards: mbed_lpc1768: Improve documentation
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-10 19:29:55 +00:00
benpicco
b44cf48a87
Merge pull request #13246 from benpicco/lpc23xx-spi
...
cpu/lpc2387: make SPI configurable
2020-02-10 17:01:41 +01:00
Marian Buschsieweke
f5d9f29b57
boards/arduino-leonardo: Refactor avrdude conf
2020-02-10 15:01:27 +01:00
Marian Buschsieweke
7f4782e3e6
boards/arduino-duemilanove: Refactor avrdude conf
2020-02-10 15:01:06 +01:00
Marian Buschsieweke
c1c25b0644
boards/arduino-nano: Refactor avrdude conf
...
- Use the common logic to translate from a bootloader to concrete flasher flags
- Extended documentation on how to use optiboot as alternative bootloader, as
the stock bootloader is affected by a bug preventing the use of RIOT's
pm_reboot() implementation
2020-02-10 14:59:24 +01:00
Marian Buschsieweke
88b90ee4af
boards/arduino-uno: Refactor avrdude conf
2020-02-10 14:59:06 +01:00
Marian Buschsieweke
23531b3a73
boards/arduino-mega2560: Refactor avrdude conf
2020-02-10 14:58:18 +01:00
Marian Buschsieweke
750d3078e4
boards/common/arduino-atmega: Refactoring
...
- including `avrdude.mk` and `serial.mk` is no longer needed
- the avrdude flag -F is dropped
- This allows flashing a board having an MCU different to the one
RIOT was compiled for
- It is better to let the user provide this flag manually if she/he really
wants to turn safety off, knows what she/he is doing, and accepts the
risk associated with this
- the avrdude flag -D is dropped
- This disables issuing an erase command during flashing, however this
erase cycle is strictly required to be able to program the flash
- This is only needed in case of the stk500v2 bootloader, which implicitly
does the erase cycle and fails if explicitly asked to do so
- Only for the stk500v2 bootloader this flag is now added
2020-02-10 14:52:07 +01:00
Marian Buschsieweke
95704348ae
boards/common/atmega: Refactor flash & serial conf
...
- Include `tools/avrdude.mk` and `tools/serial.mk` at the common place instead
for each ATmega based board individually
- Introduce the makefile variable BOOTLOADER to de-duplicate flash configs:
- Two boards using the same bootloader now just use `BOOTLOADER ?= foo`
and share the individual config
- These settings are not applied when `PROGRAMMER` is set to still allow
users to manually specify how to program their board
2020-02-10 14:48:39 +01:00
Benjamin Valentin
d675eb7cbb
boards/mcb2388: update SPI configuration
2020-02-10 13:41:00 +01:00
Benjamin Valentin
4342d81220
boards/mcb2388: add ADC configuration
...
The MCB2388 has a potentiometer connected to an ADC input.
2020-02-10 13:25:26 +01:00
Benjamin Valentin
9c0dfaada9
boards/msba2: add ADC configuration
...
ADC pins are on the AD/DA pins (JP8).
Configure AD0.0 - AD0.2 as laid out on the board schematics.
2020-02-10 13:25:26 +01:00
Francois Berder
b4ab22673e
boards: Use ARRAY_SIZE for setting UART_NUMOF, SPI_NUMOF, I2C_NUMOF
...
Signed-off-by: Francois Berder <18538310+francois-berder@users.noreply.github.com>
2020-02-09 20:55:46 +00:00
Francisco Molina
c9ff150571
boards/sam%21-xpro: prefer XOSC32K for RTC/RTT (GCLK2)
2020-02-07 15:48:15 +01:00
713fead00a
boards: move some USEMODULE to Makefile.dep
2020-02-07 13:21:22 +01:00
benpicco
66c7c63c94
Merge pull request #13061 from gschorcht/cpu/esp32/rtc_xtal_32k
...
cpu/esp32: allow external 32 kHz crystal for the RTC hardware timer
2020-02-07 10:24:22 +01:00
Gunar Schorcht
1e71606305
boards/esp32: enable 32 kHz XTAL for WROVER-KIT
2020-02-07 00:46:16 +01:00
benpicco
3d95521c14
Merge pull request #13301 from gschorcht/board/esp32/fix_compile_error_c_linkage
...
boards/esp32: fix compilation error due to C linkage in examples/posix_sockets
2020-02-05 22:08:14 +01:00
Gunar Schorcht
cfcea03a58
board/esp32: fix compilation error due to C linkage
...
Including `board_common.h` header has to be outside the `extern C` linkage block.
2020-02-05 20:42:22 +01:00
d6264f56c8
Merge pull request #13168 from fjmolinas/pr_iotlab_openocd
...
boards/iotlab: add DEBUG_ADAPTER_ID openocd
2020-02-05 11:30:11 +01:00
Benjamin Valentin
c4e0ed4b79
boards: use explicit GCLK_SRC defines
2020-02-04 21:17:00 +01:00
Benjamin Valentin
4fbca251bc
boards/same54-xpro: use 48 MHz GCLK6 for I2C
...
We can't run I2C off the 120 MHz main clock as the availiable dividers are too small.
Use the 48 MHz GCLK 6 instead which offers an appropriate frequency.
fixes #12037
2020-02-04 21:16:54 +01:00
Benjamin Valentin
1496149bba
cpu/sam0: don't hard-code peripheral clocks
...
Instead of hard-coding the peripheral clocks to CLOCK_CORECLOCK
introduce helper functions to return the frequency of the individual
GCLKs and use those for baud-rate calculations.
This requires the GCLK to be part of the peripheral's config struct.
While this is already the case for most peripherals, this also adds
it for those where it wasn't used before.
As it defaults to 0 (CLOCK_CORECLOCK) no change is to be expected.
2020-02-04 21:06:21 +01:00
Benjamin Valentin
a51d167a43
cpu/sam0: use GCLK ID instead of bitmask
...
To simplify board definitions and for unification between samd2x and
newer models, don't use the GCLK bitmask in board definitions.
Instead use the GCLK index and generate the bitmask when needed.
2020-02-04 21:06:21 +01:00
Jean Pierre Dudey
8c68796ff8
boards/cc1312-launchpad: correct config. for gdb_agent_server
...
This enables the usage of `monitor reset` command in gdb.
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
2020-02-04 07:13:20 -05:00
benpicco
cc90a896c7
Merge pull request #13166 from jeandudey/2020_01_19-cc26x2-cc13x2
...
cpu/cc13x2: rename cpu to cc26x2_cc13x2.
2020-02-04 11:45:59 +01:00
benpicco
5d1bf26f0c
Merge pull request #13076 from gschorcht/boards/esp32/ttgo_t_beam_gps
...
boards/esp32: enable GPS module on ESP32 TTGO T-Beam V1.0
2020-02-01 23:25:55 +01:00
Gunar Schorcht
c30674d539
boards/esp32-ttgo-t-beam: switch on GPS module
2020-02-01 16:12:05 +01:00
Gunar Schorcht
624c6f24ca
boards/esp32: allow board specific initialization
2020-02-01 16:12:05 +01:00
32f4986757
boards/hifive1*: remove useless stdio_uart include
...
stdio_uart is already pulled by default by the dependency resolution
mechanism.
2020-01-31 14:30:32 +01:00
Benjamin Valentin
985d340621
boards/avsextrem: update SPI config
2020-01-31 12:01:09 +01:00
Benjamin Valentin
3ae7bb425b
boards/msba2: update SPI configuration
2020-01-31 12:01:09 +01:00
Dylan Laduranty
d929087e57
Merge pull request #13233 from benpicco/edbg-update
...
tools/edbg: update to latest upstream version
2020-01-31 11:04:23 +01:00
benpicco
cdb427b760
Merge pull request #12475 from francois-berder/wifire-gpio-refactor
...
cpu: mips_pic32_common: Refactor GPIO peripheral
2020-01-31 09:46:57 +01:00
Benjamin Valentin
bd19a55804
boards: remove EDBG_DEVICE_TYPE
...
EDBG_DEVICE_TYPE is a property of the CPU, is should not be set
by every board individually.
2020-01-31 09:35:27 +01:00
Sören Tempel
8485c535d5
waspmote-pro: don't build the boards_common_atmega module
...
Only include its headers. Without this change board_init would be
defined twice. Once in `boards/waspmote-pro/board.c` and the other time
`boards/common/atmega/board.c`.
2020-01-29 12:32:16 +01:00
Francisco Molina
94853d5e1d
boards/iotlab-%: define DEBUG_ADAPTER
2020-01-28 11:56:56 +01:00
Francisco Molina
f79397f7be
boards/iotlab-%: use common openocd config
2020-01-28 11:56:38 +01:00
98995f685b
Merge pull request #13179 from fjmolinas/pr_openocd_stm32f7_probe
...
boards/nucleo-f767zi: add correct flash bank openocd config
2020-01-28 10:48:23 +01:00
Francisco Molina
1dec5ba61b
boards/common/stm32f7: add correct flash bank configuration
...
openocd configuration file for `stm32f7` relies on probing to find out
FLASH_ADDR. On nucleo-f767zi board probing (`flash probe 0`) fails when
`srst` is asserted, but `srst` needs to be asserted to be able to flash
the `BOARD` when sleeping or after a hardfault.
To circumvent this in boards/common/stm32/dist/stm32f7.cfg we define a new
flash bank with the appropriate fash start address and specify that this is
the flash bank to be used as default configuration instead of the
default by setting FLASH_BANK=4
2020-01-27 22:32:06 +01:00
