19618: cpu/stm32: fix riotboot settings for L4 and WB r=benpicco a=gschorcht
### Contribution description
This PR fixes the `riotboot` configuration for L4 and WB.
The family is not called `stm32l4` or `stm32wb` but `l4` and `wb`. That is, the `riotboot` configuration didn't work at all. Furthermore, a minimum `RIOTBOOT_LEN` of `0x2000` is required for L4.
Found when investigating the compilation errors for `bootloaders/riotboot_serial` in PR #19576.
### Testing procedure
1. Green CI.
2. Use the following commands:
```
BOARD=nucleo-l496zg make -C tests/riotboot info-debug-variable-RIOTBOOT_HDR_LEN
BOARD=p-nucleo-wb55 make -C tests/riotboot info-debug-variable-RIOTBOOT_HDR_LEN
```
In master these commands give
```
0x400
```
With this PR these commands give
```
0x200
```
as expected.
3. Use the following commands:
```
BOARD=nucleo-l496zg make -C tests/riotboot info-debug-variable-RIOTBOOT_LEN
BOARD=p-nucleo-wb55 make -C tests/riotboot info-debug-variable-RIOTBOOT_LEN
```
In master these commands give
```
0x1000
```
With this PR these commands give
```
0x2000
```
as expected.
### Issues/PRs references
19639: tests/net/gnrc_mac_timeout: add automated test r=aabadie a=aabadie
19644: gnrc_ipv6_nib: include RIO with all subnets in downstream RA r=benpicco a=benpicco
19649: gnrc_sixlowpan_iphc: prefix bits outside context must be zero r=benpicco a=benpicco
19656: gnrc/ipv6_auto_subnets: allow to configure minimal prefix length r=benpicco a=benpicco
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
19335: ipv6/nib: 6LBR should not send RS on their downstream interface r=fabian18 a=fabian18
19581: cpu/samd5x: enable FDPLL1 at 200MHz r=benpicco a=dylad
### Contribution description
This PR allows to use the second FDPLL (the first one is used to generated the 120MHz frequency used by the core and some peripherals). The second FDPLL is setup to run at 200MHz which is the maximum allowed by this MCU.
In fact, I reused the existing function which setup FDPLL0 so it can be used in a generic way for both PLL (since they are the same IP).
I change the way the computation offset (left shift by 5) is done because 200MHz << 5 wouldn't fit inside an `uint32_t` and I wanted to avoid using an `uint64_t` here
Two additional commits are present for a small cleanup and a fix.
This is currently unused in our codebase, so it shouldn't impact this platform too much as the `ONDEMAND` bit is set. the FDPLL will not be running out of the box. But `@gschorcht` might need it pretty soon.
### Testing procedure
This PR can be tested on a `same54-xpro` and an oscilloscope using the following the patch:
```
From 76490845ec72387b24116bdd364a61365c186aa1 Mon Sep 17 00:00:00 2001
From: Dylan Laduranty <dylan.laduranty@mesotic.com>
Date: Thu, 11 May 2023 17:42:16 +0200
Subject: [PATCH] removeme! for debug purpose
Signed-off-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
---
cpu/samd5x/cpu.c | 8 +++++++-
1 file changed, 7 insertions(+), 1 deletion(-)
diff --git a/cpu/samd5x/cpu.c b/cpu/samd5x/cpu.c
index f778991a5b..2866c8c9e5 100644
--- a/cpu/samd5x/cpu.c
+++ b/cpu/samd5x/cpu.c
`@@` -220,7 +220,7 `@@` static void fdpll_init(uint8_t idx, uint32_t f_cpu)
}
static void gclk_connect(uint8_t id, uint8_t src, uint32_t flags) {
- GCLK->GENCTRL[id].reg = GCLK_GENCTRL_SRC(src) | GCLK_GENCTRL_GENEN | flags | GCLK_GENCTRL_IDC;
+ GCLK->GENCTRL[id].reg = GCLK_GENCTRL_SRC(src) | GCLK_GENCTRL_GENEN | flags | GCLK_GENCTRL_OE | GCLK_GENCTRL_IDC;
while (GCLK->SYNCBUSY.reg & GCLK_SYNCBUSY_GENCTRL(id)) {}
}
`@@` -384,6 +384,12 `@@` void cpu_init(void)
dma_init();
#endif
+ sam0_gclk_enable(SAM0_GCLK_200MHZ);
+ /* output both FDPLL (GCLK0 and GCLK4) to gpios */
+ gpio_init_mux(GPIO_PIN(PB, 14), GPIO_MUX_M);
+ gpio_init_mux(GPIO_PIN(PB, 10), GPIO_MUX_M);
+ /* PB14 -> EXT2 PB10 -> QSPI SCK */
+
/* initialize stdio prior to periph_init() to allow use of DEBUG() there */
early_init();
--
2.35.3
```
It will output both FDPLLs to PB14 and PB10. Their frequency can then be measured using an oscilloscope.
### Issues/PRs references
None.
19612: pkg/ndn-riot: drop unmaintained pkg r=benpicco a=maribu
### Contribution description
Upstream [1] has seen no activity since 2018, so it safe to assume this is dead. It is reasonable to assume that any users - if there ever were any - have moved on.
Fixes https://github.com/RIOT-OS/RIOT/issues/15638
[1]: https://github.com/named-data-iot/ndn-riot
19643: examples/suit_update: some test fixes r=aabadie a=kaspar030
19655: net/ipv6: make use of clz in ipv6_addr_match_prefix() r=benpicco a=benpicco
Co-authored-by: Fabian Hüßler <fabian.huessler@st.ovgu.de>
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Co-authored-by: Kaspar Schleiser <kaspar@schleiser.de>
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
The family is not called `stm32l4` or `stm32wb` but `l4` and `wb`. That is, the `riotboot` configuration didn't work. A minimum `RIOTBOOT_LEN` of `0x2000` is required for WB.
19611: sys/net/rpl: fix possible NULL dereference r=benpicco a=maribu
### Contribution description
As the title says
19640: core/thread: drop unused thread_arch_t r=benpicco a=maribu
### Contribution description
No architecture makes use of thread_arch_t anymore, so let's drop it.
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
19628: Fix periph clk r=aabadie a=Enoch247
### Contribution description
This fixes some minor doc and argument type errors. See commit messages for details.
### Testing procedure
It compiles without errors for me.
### Issues/PRs references
None known
19637: sys/usb/usbus_msc: fix typo in C expression r=aabadie a=maribu
### Contribution description
Rather than setting the correct blk_len, the code only wrote 1 and 0 into the three bytes due to the use of a logic and where a bitwise and should be used.
Co-authored-by: Joshua DeWeese <jdeweese@primecontrols.com>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
19433: cpu/esp32: deduplication in Kconfig for ESP32x SoCs r=aabadie a=gschorcht
### Contribution description
This PR reduces the code duplication in Kconfig for ESP32x SoCs.
It defines a new common CPU symbol `CPU_COMMON_ESP32X` in Kconfig that is used by all `CPU_FAM_ESP32x` symbols. It selects all features, modules and packages that are common for all ESP32x SoC variants. This avoids the selection of features, modules and packages again and again for each ESP32x SoC variant.
The same is done in PR #19432 for common ESP32x board definitions.
### Testing procedure
Green CI
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19619: cpu/arm7: Fix undefined behavior based on invalid assembly r=aabadie a=Teufelchen1
### Contribution description
Hellooo! 🦤
In this PR a single `NOP` is added after an `ldm` in ARM7 common code in the scheduling management.
The change is necessary because this particular `ldm` affects certain banked registers, including `R14 / lr`. The next instruction then immediately accesses `lr`. This is invalid and the exact effect depends on the underlying hardware implementation. An intermediate `NOP` ensures correct behaviour in such cases.
The ARM docs can be found [here](https://documentation-service.arm.com/static/5f8dacc8f86e16515cdb865a), in section `A4.1.21 LDM (2)`. It states:
> In ARM architecture versions earlier than ARMv6, this form of LDM must not be
followed by an instruction that accesses banked registers. A following NOP is a good
way to ensure this.
### Testing procedure
Without this change, on the Game Boy Advance, RIOT behaves irregularly. With the `NOP`, it works fine!
If possible, this change should be tested on other ARM7 hardware as well but I do not have access to any.
----
Special thanks `@pyropeter` for spotting the extremely tiny note on this issue within the ARM docs. You saved me hours of tears! 👾
Co-authored-by: Teufelchen1 <bennet.blischke@outlook.com>
19572: cpu/stm32/periph_pwm: support of complementary timer outputs r=maribu a=gschorcht
### Contribution description
This PR provides the support of complementary timer outputs as PWM channels for advanced timers (TIM1/TIM8).
To use a complementary output of an advanced timer as PWM channel, the output is defined with an offset of 4, i.e. normal outputs are in the range of 0 to 3 (CH1...CH4) and complementary outputs are in the range of 4 to 6 (CH1N...CH3N). If the defined output is less than 4, the normal output is enabled, otherwise the complementary output is enabled.
This change is required to support PWM on boards that have connected the complementary outputs of advanced timers to the PWM connector pins, for example the STM32L496-DISCO board.
### Testing procedure
- Green CI
- Use any STM32 board which supports the `periph_pwm` feature. `tests/periph_pwm` should still work.
- Change the configuration for this board so that either timer TIM1 or TIM8 and a complementary channel is used for any exposed GPIO. `tests/periph_pwm` should also work with such a configuration.
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
To use a complementary output of an advanced timer as PWM channel, the output is defined with an offset of 4, i.e. normal outputs are in the range of 0 to 3 (CH1...CH4) and complementary outputs are in the range of 4 to 6 (CH1N...CH3N). If the defined output is less than 4, the normal output is enabled, otherwise the complementary output is enabled.
- Replace all users of `$(RIOTBASE)/build` with the already present
`$(BUILD_DIR)` variable
- Replace all users of `$(BUILD_DIR)/pkg` with the already present
`$(PKGDIRBASE)` variable
- Create a `CACHEDIR.TAG` file in the `$(BUILD_DIR)`
These functions can be used to set both FDPLL0 and FDPLL1 by using an extra argument 'idx' (index) and allow to set the ONDEMAND bit using the 'flags' argument
Signed-off-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Provide a common clock initialization driver rather than leaving
clock initialization to the boards code. A declarative description of
the board's clock configuration using a struct does still allow to
fine-tune settings. In addition, a board is still allowed to just
provide a custom `void clock_init(void)` if there really is the need
to do crazy things.
18056: pkg/cmsis: use unique package for CMSIS headers, DSP and NN modules r=benpicco a=aabadie
19571: cpu/stm32/periph_adc: fixes and improvements for L4 support r=benpicco a=gschorcht
### Contribution description
This PR provides the following fixes and improvements for the `periph_adc` implementation for STM32L4.
- Support STM32L496AG added.
- Instead of defining the number of ADC devices for each MCU model, the number of ADC devices is determined from ADCx definitions in CMSIS header.
- MCU specific register/value defines are valid for all L4 MCUs, model based conditional compilation is removed.
- The ADC clock disable function is fixed using a counter. The counter is incremented in `prep` and decremented in `done`. The ADC clock is disabled if the counter becomes 0.
- For boards that have not connected the V_REF+ pin to an external reference voltage, the VREFBUF peripheral can be used as V_REF+ (if supported) by setting `VREFBUF_ENABLE=1`.
- The ASCR register is available and has to be set for all STM32L471xx, STM32L475xx, STM32L476xx, STM32L485xx and STM32L486xx MCUs. Instead of using the CPU model for conditional compilation, the CPU line is used to support all MCU of that lines.
- Setting of SQR1 is fixed. Setting the SQR1 did only work before because the `ADC_SRQ_L` is set to 0 for a sequence length of 1.
- Setting the `ADC_CCR_CKMODE` did only work for the reset state. It is now cleared before it is set. Instead of using the `ADC_CCR_CKMODE_x` bits to set the mode, the mode defines are used.
- Support for V_REFINT as ADC channel added.
### Testing procedure
19589: gnrc/gnrc_netif_hdr_print: printout timestamp if enabled r=aabadie a=chudov
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: chudov <chudov@gmail.com>
Setting the `ADC_CCR_CKMODE` did only work for the reset state. It is now cleared before it is set. Instead of using the `ADC_CCR_CKMODE_x` bits to set the mode, the mode defines are used.
19573: cpu/stm32/periph_dac: small improvements r=maribu a=gschorcht
### Contribution description
This PR provides the following improvements for `periph_dac` on STM32
- Support for `RCC_APB1ENR1_DAC1EN` symbol added.
- For boards that have not connected the V_REF+ pin to an external reference voltage, the VREFBUF peripheral can be used as V_REF+ (if supported) by setting `VREFBUF_ENABLE=1`.
- If the DAC peripheral has a mode register (`DAC_MCR`), it is set to normal mode with buffer enabled and connected to external pin and on-chip peripherals. This allows to measure the current value of a DAC channel with an ADC channel or to use the DAC channel also for other on-chip peripherals.
### Testing procedure
- Green CI
- `tests/periph_dac` should still work for any board supporting the `periph_dac` feature.
### Issues/PRs references
19579: doc/doxygen/src/flashing.md: work around Doxygen bug r=maribu a=maribu
### Contribution description
Doxygen fails to render inline code in headers correctly in the version the CI uses. So, work around the issue by not typestetting `stm32flash` as inline code but as regular text.
19583: tests: move cpu related applications to tests/cpu r=maribu a=aabadie
19584: tests/build_system/external_board_dirs: fix broken symlinks r=maribu a=aabadie
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
19565: tests: move core related applications to their own tests/core/ folder r=maribu a=aabadie
19568: tests: move remaining driver related applications to tests/drivers r=maribu a=aabadie
19574: cpu/stm32/periph_gpio: reset PU/PD for ADC channels r=maribu a=gschorcht
### Contribution description
This PR provides a small fix that is relevant when a GPIO has been used as input/output with a pull resistor before it is initialized as an ADC channel.
The PU/PD configuration has to be `0b00` for analog outputs which is corresponds to the reset state. However, if the GPIO is not in the reset state but was used digital input/output with any pull resistor, the PU/PD configuration has also to be reset to use it as ADC channel.
### Testing procedure
- Green CI
- The `periph_adc` test application should still work for any board that supports the `periph_adc` feature.
### Issues/PRs references
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19484: makefiles/arch/msp430.inc.mk: Fix compilation issues with GCC 12 r=maribu a=maribu
### Contribution description
This fixes the following compilation issues:
/home/maribu/Repos/software/RIOT/cpu/msp430fxyz/periph/gpio.c: In function 'gpio_periph_mode':
/home/maribu/Repos/software/RIOT/cpu/msp430fxyz/periph/gpio.c:95:15: error: array subscript 0 is outside array bounds of 'msp_port_isr_t[0]' [-Werror=array-bounds]
95 | sel = &(isrport->SEL);
| ^~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
by adding `CFLAGS += --param-min-pagesize=0` for GCC 12 (same issue as already fixed for AVR).
and:
/usr/lib/gcc/msp430-elf/12.2.0/../../../../msp430-elf/bin/ld: warning: /home/maribu/Repos/software/RIOT/cpu/msp430_common/ldscripts/xfa.ld contains output sections; did you forget -T?
by adding the missing `-T`.
### Testing procedure
The following should still work:
- `make BOARD=msb-430 -C examples/hello-world`
- `make BOARD=msb-430 -C tests/xfa flash test`
### Issues/PRs references
None
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
The ASCR register is available and has to be set for all STM32L471xx, STM32L475xx, STM32L476xx, STM32L485xx and STM32L486xx MCUs. Instead of using the CPU model for conditional compilation, the CPU line is used to support all MCU of that lines.
For boards that have not connected the V_REF+ pin to an external reference voltage, the VREFBUF peripheral can be used as V_REF+ if supported by setting `VREFBUF_ENABLE=1`.
The ADC clock disable is fixed using a counter. The counter is incremented in `prep` and decremented in `done`. The ADC clock is disabled if the counter becomes 0.
