To be able to define common configurations for all ESP CPUs, the CPU specific configuration cpu_conf.h has to include a common configuration. For that purpose cpu_conf.h in cpu/esp_common is renamed to cpu_conf_common.h and included in CPU specific configurations.
The split between GEN2_ULP32K and GEN3_ULP32K was introduced to fix
a failure in tests/periph_wdt when the external oscillator was used.
By not running the external oscillator on demand, the failure can no
longer be observed, so default GEN3_ULP32K to GEN2_ULP32K.
The lpc23xx MCU has up to three I2C interfaces.
This adds a driver for it.
The peripheral works in interrupt mode, each change of the state machine
will generate an interrupt.
The response to the states are laid out in the data sheet.
This replaces the old driver that was removed in c560e28eb6
All the more recent vendor files have them, so include them for samr30 too.
It is expected for this to become obsolete with the next vendor file update.
During the write access to the SPI flash, the IROM cache is not available and only code from the IRAM can be executed. Therefore, the code of file system implementations which access the SPI flash must reside in IRAM.
For consistency, use named GCLKs.
- `SAM0_GCLK_32KHZ` will always be 2 for samd21
- `SAM0_GCLK_MAIN` will always be 0
So no change in functionality, just makes the code easier to understand.
The same tool 'gen_esp32part.py' is used for the generation of partition tables on ESP8266 as well as n ESP32. The tool is therefore added to 'dist/tools/esptool'
Creating an `exti_config` array for a new MCU manually is tedious and error prone.
Luckiely all information is already availiable in the vendor files.
Credit for this discovery & method goes to @Sizurka
The file was generated with
```C
int main(void) {
puts("static const int8_t exti_config[PORT_GROUPS][32] = {");
for (unsigned port = 1; port < 5; ++port) {
printf("#if PORT_GROUPS >= %d\n{\n", port);
for (unsigned pin = 0; pin < 32; ++pin) {
printf("#ifdef PIN_P%c%02uA_EIC_EXTINT_NUM\n", '@' + port, pin);
printf(" PIN_P%c%02uA_EIC_EXTINT_NUM,\n", '@' + port, pin);
printf("#else\n -1,\n#endif\n");
}
printf("},\n#endif\n\n");
}
puts("};");
return 0;
}
```
No changes in generated code are expected, but this makes adding new members
of the sam0 CPU families much easier.
Set the ONDEMAND bit so clocks are only run if they have a user configured.
This saves 390 µA on same54-xpro.
examples/default:
before: 3.88 mA
after : 3.49 mA
examples/gnrc_networking: (with REB215-XPRO EXT3)
before: 13.29 mA
after : 12.9 mA
samr30 is the only MCU of this family where the vendor files do not
define the PIN_($pin)_EIC_EXTINT_NUM macro yet.
This macro is needed to create a generic EXTI configuration for all
sam0 MCUs.
The defines were generated with
sed -Ei '/define PIN_(.*)_EIC_EXTINT([0-9]*)/
{h; x;
s/define PIN_(.*)A_EIC_EXTINT([0-9]*)(.*)/
define PIN_\1A_EIC_EXTINT_NUM _L_\(\2\)
\/**< \brief EIC signal: PIN_\1 External Interrupt Line *\/
/g; G}' samr30g18a.h samr30e18a.h
Previous value was 20 K, now it's 80 K. The older family of these MCUs
(cc13x0, cc26x0) had that size, currently for cc13x2 and cc26x2 it's
80 K.
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
From the data sheet:
> **Note:** Only in case when a reset occurs and the POR = 0, the BODR bit
indicates if the V DD(DCDC)(3V3) voltage was below 2.6 V or not.
So the value of BODR is undefined if POR is set.
Clear it to bring it to a defined state.
The function would always return `true` after early boot, so it
is not very useful for applications.
Now it will only (but always) return true when we woke from Deep Sleep
*after* early boot. This makes it behave the same ways as the function
of the same name on SAME54.
Rename the existing function to cpu_backup_ram_is_initialized() to better
match it's semantics.
On the MCB2388 plugging the power will result in both the POR and EXTR
bit being set.
Not sure if this is a property of the board, but it means RTC is also
reset after programming, so it behaves just like Backup RAM.
If we woke from Deep Sleep the POR bit will be cleared, so the RTC is not
reset.
