Add support for querying the frequency supported by
`periph_timer`. This allows applications which require
this feature to run on the `native` board.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
The tramp assembly was missing a `.note.GNU-stack` section,
meaning the compiler was forced to assume that we require
an executable stack.
Fix this by adding the necessary section.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
The underlying peripheral can only read from RAM. This uses the
existing infrastructure (already needed to work around the lack of a
hardware support for I2C_NOSTART) to unconditionally copy any to-be-sent
data into RAM.
This adds the features
- periph_gpio_ll_input_pull_down:
To indicate support for input mode with internal pull down
- periph_gpio_ll_input_pull_keep:
To indicate support for input mode with internal resistor
pulling towards current level
- periph_gpio_ll_input_pull_up:
To indicate support for input mode with internal pull up
- periph_gpio_ll_disconnect:
To indicate a GPIO can be disconnected
- periph_gpio_ll_open_drain:
To indicate support for open drain mode
- periph_gpio_ll_open_drain_pull_up:
To indicate support for open drain mode with internal pull up
- periph_gpio_ll_open_source:
To indicate support for open source mode
- periph_gpio_ll_open_source_pull_down:
To indicate support for open source mode with internal pull down
- Move common code for USART (shared SPI / UART peripheral) to its
own file and allow sharing the USART peripheral to provide both
UART and SPI in round-robin fashion.
- Configure both UART and SPI bus via a `struct` in the board's
`periph_conf.h`
- this allows allocating the two UARTs as needed by the use case
- since both USARTs signals have a fixed connection to a single
GPIO, most configuration is moved to the CPU
- the board now only needs to decide which bus is provided by
which USART
Note: Sharing an USART used as UART requires cooperation from the app:
- If the UART is used in TX-only mode (no RX callback), the driver
will release the USART while not sending
- If the UART is used to also receive, the application needs to power
the UART down while not expecting something to send. An
`spi_acquire()` will be blocked while the UART is powered up.
This commit optimizes the `gpio_conf_t` type in the following
regards:
- The "base" `gpio_conf_t` is stripped from members that only some
platforms support, e.g. drive strength, slew rate, and disabling of
the Schmitt Trigger are no longer universally available but
platform-specific extensions
- The `gpio_conf_t` is now crammed into a bit-field that is 8 bit or
16 bit wide. This allows for storing lots of them e.g. in
`driver_foo_params_t` or `uart_conf_t` etc.
- A `union` of the `struct` with bit-field members and a `bits` is used
to allow accessing all bits in a simple C statement and to ensure
alignment for efficient handling of the type
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Expose the compile time configuration knob `CONFIG_AFIO_PCF0_SWJ_CFG`
to allow freeing some/all JTAG pins and use them as GPIOs.
As default, PB4 is remapped from NJTRST to be usable as regular GPIO.
This still allows using the JTAG interface for debugging/flashing,
but makes an GPIO exposed by some boards available.
The API doc clearly states that arbitrary high PWM frequencies can
be requested and the driver should reduce the frequency while keeping
the resolution, when required. So change the code to just do that
rather than blowing assertions.
The function configures additional features of the DMA stream for F2/F4/F7.
`dma_setup_ext` added to configure F2/F4/F7 specific additional features like `MBURST`, `PBURST`, `FIFO` and Peripheral flow controller. It is supposed to be used after `dma_setup` and `dma_prepare`.
timer_set has no documented restriction on this being not null, other
implementations explicitly tolerate it (rpx0xx checks inside the ISR,
but doing it at init time keeps the ISR slim).
This is useful when using a timer just to read, without any action when
it triggers (the action is taken depending on read values, eg. in a
thread context).
- boot the I2C after init in low power mode
- otherwise I2C will consume more power until the first time it is
used, which is surprising
- STM32 F1 only: reconfigure SCL and SDA as GPIOs while the I2C
peripheral is powered down
- When the I2C peripheral is not clocked, it drives SCL and SDA
down. This will dissipate power across the pull up resistor.
- add support for multiple timers
- add support for selecting clock source in the board's `periph_conf.h`
- add support for the prescaler
- implement `periph_timer_query_freqs`
- add a second timer to all MSP430 boards
- the first timer is fast ticking, high-power
- the second is slow ticking, low-power
The functions `uart_poweron()`, `uart_poweroff()` and `uart_mode()`
can share code between the UART (UART without EasyDMA) and UARTE
(UART with EasyDMA) implementations, so let's do that.
- nRF51: Use `uart_conf_t` for consistency with nRF52
- nRF52832: Use UARTE (UART with EasyDMA) over UART (without DMA), as
done for all other nRF52 family members
- use `UARTE_PRESENT` to detect whether an UARTE can be used, rather
than family names
The `i2c_read_bytes()` and `i2c_write_bytes()` function return the
number of bytes written / read, instead of `0` as the API contract
says. This fixes the issue.
With only 8 possible prescalers, we can just loop over the values
and shift the clock. In addition to being much easier to read, using
shifts over divisions can be a lot faster on CPUs without hardware
division.
In addition an `assert()` is added that checks if the API contract
regarding the SPI frequency is honored. If the requested clock is too
low to be generated, we should rather have a blown assertion than
hard to trace communication errors.
Finally, the term prescaler is used instead of divider, as divider may
imply that the frequency is divided by the given value n, but
in fact is divided by 2^(n+1).
Previously, the /CS signal was performed by enabling / disabling the
SPI peripheral. This had the disadvantage that clock polarity settings
where not applied starting with `spi_acquire()`, as assumed by e.g.
the SPI SD card driver, but only just before transmitting data.
Now the SPI peripheral is enabled on `spi_acquire()` and only disabled
when calling `spi_release()`, and the `SPI_CR2_SSOE` bit in the `CR2`
register is used for hardware /CS handling (as supposed to).
This doesn't change the firmware, since for all STM32 MCUs with an
SPI driver the register setting in the mode did match the SPI mode
number by chance. But for some STM32 MCUs with no SPI driver yet
the register layout is indeed different. This will help to provide an
SPI driver for them as well.
