The register access to SMPR1/SMPR2 was incorrect in three aspects:
1. For channels < 10, SMPR1 was cleared but SMPR2 should have been
cleared
2. The code was not thread-safe
3. An unneeded write was issued. (The compiler won't combine the
in-place bitwise operations into a single read-modify-write
sequence on `volatile` memory.)
Fixes https://github.com/RIOT-OS/RIOT/issues/20261
The separate Schmitt trigger bit in the configuration is dropped, as
the Schmitt trigger is only every disabled when in `GPIO_DISCONNECT`
mode. So no need to encode the same information twice.
The `gpio_state_t` is improved to be a bitmask that holds the
MODER register value and a flag indicating whether open-drain mode
should be enabled.
Finally, `GPIO_DISCONNECT` is implemented. This is done by placing the
GPIO in analog mode, which by disabling the Schmitt trigger reduces
power consumption.
This adds the features
- periph_gpio_ll_input_pull_down:
To indicate support for input mode with internal pull down
- periph_gpio_ll_input_pull_keep:
To indicate support for input mode with internal resistor
pulling towards current level
- periph_gpio_ll_input_pull_up:
To indicate support for input mode with internal pull up
- periph_gpio_ll_disconnect:
To indicate a GPIO can be disconnected
- periph_gpio_ll_open_drain:
To indicate support for open drain mode
- periph_gpio_ll_open_drain_pull_up:
To indicate support for open drain mode with internal pull up
- periph_gpio_ll_open_source:
To indicate support for open source mode
- periph_gpio_ll_open_source_pull_down:
To indicate support for open source mode with internal pull down
This commit optimizes the `gpio_conf_t` type in the following
regards:
- The "base" `gpio_conf_t` is stripped from members that only some
platforms support, e.g. drive strength, slew rate, and disabling of
the Schmitt Trigger are no longer universally available but
platform-specific extensions
- The `gpio_conf_t` is now crammed into a bit-field that is 8 bit or
16 bit wide. This allows for storing lots of them e.g. in
`driver_foo_params_t` or `uart_conf_t` etc.
- A `union` of the `struct` with bit-field members and a `bits` is used
to allow accessing all bits in a simple C statement and to ensure
alignment for efficient handling of the type
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
The function configures additional features of the DMA stream for F2/F4/F7.
`dma_setup_ext` added to configure F2/F4/F7 specific additional features like `MBURST`, `PBURST`, `FIFO` and Peripheral flow controller. It is supposed to be used after `dma_setup` and `dma_prepare`.
- boot the I2C after init in low power mode
- otherwise I2C will consume more power until the first time it is
used, which is surprising
- STM32 F1 only: reconfigure SCL and SDA as GPIOs while the I2C
peripheral is powered down
- When the I2C peripheral is not clocked, it drives SCL and SDA
down. This will dissipate power across the pull up resistor.
With only 8 possible prescalers, we can just loop over the values
and shift the clock. In addition to being much easier to read, using
shifts over divisions can be a lot faster on CPUs without hardware
division.
In addition an `assert()` is added that checks if the API contract
regarding the SPI frequency is honored. If the requested clock is too
low to be generated, we should rather have a blown assertion than
hard to trace communication errors.
Finally, the term prescaler is used instead of divider, as divider may
imply that the frequency is divided by the given value n, but
in fact is divided by 2^(n+1).
Previously, the /CS signal was performed by enabling / disabling the
SPI peripheral. This had the disadvantage that clock polarity settings
where not applied starting with `spi_acquire()`, as assumed by e.g.
the SPI SD card driver, but only just before transmitting data.
Now the SPI peripheral is enabled on `spi_acquire()` and only disabled
when calling `spi_release()`, and the `SPI_CR2_SSOE` bit in the `CR2`
register is used for hardware /CS handling (as supposed to).
This doesn't change the firmware, since for all STM32 MCUs with an
SPI driver the register setting in the mode did match the SPI mode
number by chance. But for some STM32 MCUs with no SPI driver yet
the register layout is indeed different. This will help to provide an
SPI driver for them as well.
The CR2 register was only written to if the settings differ from the
reset value. This wasn't actually a bug, since it was cleared in
`spi_release()` to the reset value again. Still, it looks like a bug,
may cause a pipeline flush due to the branch, and increased `.text`
size. So let's get rid of this.
The `SWJ_CFG` field of the `AFIO_MAPR` register is write only and values
read are undefined (random). Hence, using `AFIO->MAPR |= mask;` to
enable flags can corrupt the state of the `SWJ_CFG` (configure it to
an unintended value).
Two helper functions have been introduced:
- `afio_mapr_read()` reads the value, but sanitizes the `SWJ_CFG` field
to zero
- `afio_mapr_write()` writes the given value, but applies the `SWJ_CFG`
configured by the board before writing.
Finally, the `nucleo-f103rb` and `bluepill*`/`blackpill*` boards have
been updated to no longer specify `STM32F1_DISABLE_JTAG`, as this
is handled by the `SWJ_CFG` setting (which defaults to disabling JTAG).
19943: cpu/stm32: FMC used for low-level LCD parallel interface r=maribu a=gschorcht
### Contribution description
This PR provides the implementation of the LCD low-level MCU 8080 parallel interface using the FMC peripheral.
### Testing procedure
```
BOARD=stm32f723e-disco make -C tests/drivers/st77xx flash
```
and
```
BOARD=stm32l496g-disco make -C tests/drivers/st77xx flash
```
should work on top of PR #19941. Drawing operations should be much faster.
### Issues/PRs references
Depends on PR #19941
19978: treewide: fix typos to make codespell happy r=maribu a=maribu
### Contribution description
- fixes typos in comments and docs (no generated firmware changes expected)
- fixes a typo in a string in a GUI of a utility program
- add some false positives to the ignore list
### Testing procedure
- No generated binaries (except for the GUI version of the utility program to flash the MSB-A2) should change
- The diff should not look too scary
### Issues/PRs references
None
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@posteo.net>
19952: cpu/stm32/periph/eth: Disable hardware checksums r=maribu a=yarrick
lwIP will fill them in already.
Having this enabled causes empty checksums to be sent: #19853
Co-authored-by: Erik Ekman <eekman@google.com>
If the board defines `FMC_RAM_ADDR` and `FMC_RAM_LEN`, the FMC RAM is used a additional heap if module `periph_fmc` is enabled.
For that purpose
- the linker symbols `_fmc_ram_addr` and `_fmc_ram_len` are set,
- a memory region `fcmram` is added in linker script for the FMC RAM based on these `_fcm_ram_*` linker symbols
- a section for the FMC RAM is defined in this memory region that defines the heap by setting `_sheap3` and `_eheap3` and
- the number of heaps is set to 4 since to use `_sheap3` and `_eheap3` even though `_sheap1` and `_eheap1` (the backup RAM) and `_sheap2` and `_eheap2` (SRAM4) are not present.
Several STM32 families such as C0, G0, H7, L5 and U5 use `SYSTEM_STM32..XX_H` define instead of `__SYSTEM_STM32..XX_H` define to prevent multiple inclusion of `system_stm32xxxx.h`.
The RNG can use HSI48, HSI48/2 or HSI16. Using MSI as 48 MHz clock source for RNG is not possible. The clock configuration in `stmclk_u5.c` activates anyway only the MSIS but not the MSIK which could be used for certain peripherals.
Therefore, this commit
- removes the configuration of MSI as 48 MHz clock for RNG and its selection in `RCC->CCIPR1.ICLKSEL`
- enables HSI48 and selects it for RNG.
The HSI48 will also be used in future for certain peripherals such as USB OTG FS and SDMMC.
19677: boards/nucleo-l432k: provide three periph_timer instances r=maribu a=maribu
### Contribution description
- `cpu/stm32/periph_timer`: Generalize to also work with timers that do not have 4 channels
- `boards/common/stm32`: Add timer config for three timers based on TIM2, TIM15, and TIM16 (the three general-purpose timers of the STM32L4)
- `boards/nucleo-l432kc`: Make use of the new timer config
19683: cpu/sam0_eth: clean up init() r=maribu a=benpicco
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
