18682: pkg/lwext4: add lightweight implementation of the ext2/3/4 filesystem r=benpicco a=benpicco
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Boards with an integrated debugger/programmer that also provides the
serial as UART <--> USB adapter, the TTY serial matches the serial of
the programmer.
This adapts the `serial.inc.mk` to set the `DEBUG_ADAPTER_ID` to the
TTY serial if (and only if) `MOST_RECENT_PORT` *and*
`DEBUG_ADAPTER_ID_IS_TTY_SERIAL` both have a value of `1`. Boards with
an integrated programmer are expected to set
`DEBUG_ADAPTER_ID_IS_TTY_SERIAL` to `1` in their `Makefile.include`.
19256: pkg/tinyusb: add GD32VF103 support r=gschorcht a=gschorcht
### Contribution description
This PR provides the tinyUSB support for GD32VF103 and enables the `tinyusb_device` feature as well as `stdio_tinyusb_cdc_acm` for GD32VF103 boards.
### Testing procedure
```
BOARD=sipeeed-longan-nano make -C tests/shell flash term
```
should work
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19261: tests/{sys_fido2_ctap/usbus_board_reset}: fix stdio_usb_serial_jtag dependency r=gschorcht a=gschorcht
### Contribution description
This PR fixes the `stdio_usb_serial_jtag` dependency problem for `tests/sys_fido2_ctap` and `usbus_board_reset`.
- There are boards that select the STDIO backend used depending on whether `usbus` is enabled. Usually the `fido2_ctap_transport_hid` module pulls in `usbus_hid` and thus `usbus`, but since this dependency resolution is done after reading the `Makefile.dep` of the board, it may happen that the wrong STDIO backend is selected. Therefore `usbus` is selected directly in the `Makefile` of `tests/sys_fido2_ctap` .
- To improve the selection of the `stdio_usb_serial_jtag` backend in `esp32s3-pros3`, it checks for any `usbus_%` module not only `usbus`.
### Testing procedure
GreenCI
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19240: tools/doccheck: add simple exclude to doccheck r=benpicco a=kfessel
while doccheck runs for #19228 and #19220, i saw some spikes in memory consumption, turned out that was `grep -Evf dist/tools/doccheck/exclude_patterns` using about 2GB RAM. This PR changes that.
### Contribution description
add `exclude_simple` to `doccheck` drived from `exclude patterns`
`sort`ed and `uniq`ued the simple excludes
removes no longer needed patterns from `exclude patterns`
simple excludes are string rules (no patterns just strings)
how to apply these:
in this PR:
*remove the path and line number from the rule
* that made some of them doubles of each other
* sorted and uniqued them.
* this set of excludes is no longer path specific (an exception covers all paths but may of them still contain a file name)
another possible solution would be to have the excludes line number specific.
### Testing procedure
run `dist/tools/doccheck/check.sh`
compare memory consumption of
master: `grep -Evf dist/tools/doccheck/exclude_patterns`
to
this PR: `grep -Fvf dist/tools/doccheck/exclude_simple`
### Issues/PRs references
19248: cpu/gd32v: add periph_dac support r=benpicco a=gschorcht
### Contribution description
This PR provides the `periph_dac` support for GD32VF103.
### Testing procedure
`tests/periph_dac` should work on `sipeed-longan-nano` port on PA4 and PA5.
### Issues/PRs references
19255: boards/esp*: complete SD Card MTD config r=benpicco a=gschorcht
### Contribution description
This PR provides the remaining changes necessary to use the generic MTD SD Card configuration as described in PR #19216.
This includes defining the MTD offset for SD cards, since the default `MTD_0` device always uses the internal flash device, and the completion of the configuration for the ESP32 boards with a SD card interface.
### Testing procedure
`tests/vfs_default` should work now with SD Cards:
```
main(): This is RIOT! (Version: 2023.04-devel-323-gfcc07)
mount points:
/nvm0
/sd0
data dir: /sd0
> vfs df
Mountpoint Total Used Available Use%
/nvm0 3052 KiB 8 KiB 3044 KiB 0%
/sd0 7580 MiB 3632148992 B 21089792 B 99%
```
### Issues/PRs references
Co-authored-by: Karl Fessel <karl.fessel@ovgu.de>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19249: boards/gd32v: improve board definitions r=benpicco a=gschorcht
### Contribution description
This PR provides some small improvements of the existing board definitions for GD32VF103 boards for more flexibel default configurations and documentation of the board peripherals:
- Allow the remapping of SPI0 pins in SPI configuration (ae984b0bea)
- More flexible I2C configuration (0c337583b4)
The default I2C device configuration allows to define up to two I2C devices `I2C_DEV(0)` and `I2C_DEV(1)`. `I2C_DEV(0)` is always defined if the I2C peripheral is enabled by the module `periph_spi`. The second I2C device `I2C_DEV(1)` is only defined if `I2C_DEV_1_USED` is defined by the board. This allows to use the default configuration with one or two I2C devices depending on whether other peripherals are enabled that would collide with the I2C devices.
- More flexible SPI configuration (edbf59e37e)
The default SPI device configuration allows to define up to two SPI devices `SPI_DEV(0)` and `SPI_DEV(1)`. `SPI_DEV(0)` is always defined if the SPI peripheral is enabled by the module `periph_spi`. The second SPI device `SPI_DEV(1)` is only defined if `SPI_DEV_1_USED` is defined by the board. This allows to use the default configuration with one or two SPI devices depending on whether other peripherals are enabled that would collide with the SPI devices.
Furthermore, the CS signal in the SPI configuration is given by a define that can be overriden with another pin if
the default CS signal is connected to an unused hardware.
- Improve ADC config for Sipeed-Longan-Nano (c9c587ee00)
The ADC configuration was too complex. It was hard to follow when certain ADC lines are available. Furthermore, the order of ADC lines did depend on the use of other peripherals. Now, either the TFT display is not connected and all ADC lines are available or the TFT display is connected and the second SPI device is used so that only the first 4 ADC lines are available.
- Improve Kconfig for Sipeed-Longan-Nano (025f4fdf00)
Board-specific configuration not shown any longer directly in the top level menu but within a submenu.
- Improve peripherals documentation (7f0d560dd8, e24abe495a)
Available peripherals for the board are now documented in two tables ordered by RIOT peripheral names and by pins.
Although the different changes are small and mostly related to the documentation, I could split the PR if necessary.
### Testing
Green CI
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19088: boards: add esp32s3-pros3 support r=benpicco a=gschorcht
### Contribution description
This PR provides the support for [ESP32 ProS3](https://esp32s3.com/pros3.html#home) board from Unexpected Maker.
This board doesn't have a USB-to-Serial chip on board. Therefore, USB Serial/JTAG is used for STDIO and the board is flashed via the USB Seral/JTAG interface by default.
### Testing procedure
Flashing `tests/shell` should work.
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
After a reset, it can take several seconds before the CDC ACM interface becomes available as serial device `ttyACMx`. This was a change that was already made for `stdio_cdc_acm` in #19128.
The ADC configuration was too complex. It was hard to follow when certain ADC lines are available. Furthermore, the order of ADC lines did depend on the use of other peripherals. Now, either the TFT display is not connected and all ADC lines are available or the TFT display is connected and the second SPI device is used so that only the first 4 ADC lines are available.
The default SPI device configuration allows to define up to two SPI devices `SPI_DEV(0)` and `SPI_DEV(1)`. `SPI_DEV(0)` is always defined if the SPI peripheral is enabled by the module `periph_spi`. The second SPI device `SPI_DEV(1)` is only defined if `SPI_DEV_1_USED` is defined by the board. This allows to use the default configuration with one or two SPI devices depending on whether other peripherals are enabled that would collide with the SPI devices.
Furthermore, the CS signal in the SPI configuration is given by a define that can be overriden with another pin if
the default CS signal is connected to an unused hardware.
The default I2C device configuration allows to define up to two I2C devices `I2C_DEV(0)` and `I2C_DEV(1)`. `I2C_DEV(0)` is always defined if the I2C peripheral is enabled by the module `periph_spi`. The second I2C device `I2C_DEV(1)` is only defined if `I2C_DEV_1_USED` is defined by the board. This allows to use the default configuration with one or two I2C devices depending on whether other peripherals are enabled that would collide with the I2C devices.
18863: boards/esp32s2-mini: add definition for ESP32 S2 Mini r=gschorcht a=benpicco
Co-authored-by: Benjamin Valentin <benjamin.valentin@bht-berlin.de>
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
