19522: tests/periph_rtt: Fix for tick conversion test r=benpicco a=chudov
### Contribution description
Type casting and `printf` formatting for the `RTT_MAX_VALUE` and `RTT_FREQUENCY` are fixed so 32-bit value is properly handled by 'avr-libc'.
The original tick conversion test assumes that `RTT_FREQUENCY` is power of 2 so forward and backward ticks to seconds conversion results in the original ticks value. To fix it the result of the forward-backward conversion is compared with `ticktest / RTT_FREQUENCY * RTT_FREQUENCY` that considers rounding errors.
Changes were tested on deRFmega256 and nrf52840dongle.
### Testing procedure
tests/periph_rtt on a board with ATmega256RFR2 shall:
* show correct RTT_MAX_VALUE
* conversion check shall report no error.
### Issues/PRs references
Fixes#15940
Co-authored-by: chudov <chudov@gmail.com>
19368: debug: add DEBUG_BREAKPOINT() macro, set breakpoint on failed assertion r=benpicco a=benpicco
19529: cpu/stm32/periph/dac: optimize setting DAC r=benpicco a=Enoch247
### Contribution description
The current implmentation right shifted the 16 bit value passed into `dac_set()` down to the 12 bits that the DAC is actually capable of. This patch drops the shift and instead writes the 16 bit value to the DAC's left aligned 12 bit wide data holding register.
### Testing procedure
do something like:
``` c
#include "perip/dac.h"
int main(void)
{
dac_set(DAC_LINE(0), 0xffff/2);
return 0;
}
```
- observe DAC's output is half of vref
### Issues/PRs references
- none known
19531: tests/unittests: allow passing `UNIT_TESTS` via env r=benpicco a=kaspar030
Co-authored-by: Benjamin Valentin <benpicco@beuth-hochschule.de>
Co-authored-by: Joshua DeWeese <jdeweese@primecontrols.com>
Co-authored-by: Kaspar Schleiser <kaspar@schleiser.de>
19525: semtech-loramac: extend list of supported radio with sx1261, sx1262 and sx1268 r=maribu a=aabadie
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
19346: pkg/tinydtls: allow build for AVR r=benpicco a=benpicco
19512: SUBSYSTEMS.md: add jia200x to subsystems r=benpicco a=jia200x
19513: boards/nrf52840dongle/doc: Update nrfutil pointers r=benpicco a=chrysn
### Contribution description
Nordic changed its nrfutil; this change adjust to it.
I'm not fully happy with recommending that tool at all due to its bad quality (see rambling in https://github.com/RIOT-OS/RIOT/issues/19511), but short of soldering on a debug header or touch-probing it with wires it's the only way in to the device. I may later add follow-up recommendations to switch to riotboot, but this now at least fixes the immediate issue.
### Testing procedure
* Look at the updated documentation.
### Issues/PRs references
Closes: https://github.com/RIOT-OS/RIOT/issues/19511
19514: dist/testbed-support: remove obsolete boards from iotlab archi r=benpicco a=aabadie
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Benjamin Valentin <benjamin.valentin@bht-berlin.de>
Co-authored-by: Jose Alamos <jose@alamos.cc>
Co-authored-by: chrysn <chrysn@fsfe.org>
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
18620: core: add core_mutex_debug to aid debugging deadlocks r=maribu a=maribu
### Contribution description
Adding `USEMODULE += core_mutex_debug` to your `Makefile` results in
on log messages such as
[mutex] waiting for thread 1 (pc = 0x800024d)
being added whenever `mutex_lock()` blocks. This makes tracing down
deadlocks easier.
### Testing procedure
Run e.g.
```sh
USEMODULE=core_mutex_debug BOARD=nucleo-f767zi make -C tests/mutex_cancel flash test
```
which should provide output such as
```
Welcome to pyterm!
Type '/exit' to exit.
READY
s
[mutex] waiting for thread 1 (pc = 0x8000f35)
START
main(): This is RIOT! (Version: 2022.10-devel-841-g5cc02-core/mutex/debug)
Test Application for mutex_cancel / mutex_lock_cancelable
=========================================================
Test without cancellation: OK
Test early cancellation: OK
Verify no side effects on subsequent calls: [mutex] waiting for thread 1 (pc = 0x800024d)
OK
Test late cancellation: [mutex] waiting for thread 1 (pc = 0x0)
OK
TEST PASSED
```
```sh
$ arm-none-eabi-addr2line -a 0x800024d -e tests/mutex_cancel/bin/nucleo-f767zi/tests_mutex_cancel.elf
0x0800024d
/home/maribu/Repos/software/RIOT/tests/mutex_cancel/main.c:51
```
### Issues/PRs references
Depends on and includes https://github.com/RIOT-OS/RIOT/pull/18619
19296: nanocoap: allow to define CoAP resources as XFA r=maribu a=benpicco
19504: cpu/cc26xx_cc13xx: Fix bogus array-bound warning r=maribu a=maribu
### Contribution description
GCC 12 create a bogus array out of bounds warning as it assumes that because there is special handling for `uart == 0` and `uart == 1`, `uart` can indeed be `1`. There is an `assert(uart < UART_NUMOF)` above that would blow up prior to any out of bounds access.
In any case, optimizing out the special handling of `uart == 1` for when `UART_NUMOF == 1` likely improves the generated code and fixes the warning.
/home/maribu/Repos/software/RIOT/cc2650/cpu/cc26xx_cc13xx/periph/uart.c:88:8: error: array subscript 1 is above array bounds of 'uart_isr_ctx_t[1]' [-Werror=array-bounds]
88 | ctx[uart].rx_cb = rx_cb;
| ~~~^~~~~~
/home/maribu/Repos/software/RIOT/cc2650/cpu/cc26xx_cc13xx/periph/uart.c:52:23: note: while referencing 'ctx'
52 | static uart_isr_ctx_t ctx[UART_NUMOF];
| ^~~
/home/maribu/Repos/software/RIOT/cc2650/cpu/cc26xx_cc13xx/periph/uart.c:89:8: error: array subscript 1 is above array bounds of 'uart_isr_ctx_t[1]' [-Werror=array-bounds]
89 | ctx[uart].arg = arg;
| ~~~^~~~~~
/home/maribu/Repos/software/RIOT/cc2650/cpu/cc26xx_cc13xx/periph/uart.c:52:23: note: while referencing 'ctx'
52 | static uart_isr_ctx_t ctx[UART_NUMOF];
| ^~~
### Testing procedure
The actual change is a pretty obvious one-liner, so that code review and a green CI should be sufficient. If not, running any UART example app without regression should do.
### Issues/PRs references
None
19506: tools/openocd: Fix handling of OPENOCD_CMD_RESET_HALT r=maribu a=maribu
### Contribution description
The OPENOCD_CMD_RESET_HALT was not longer correctly passed to the script. This fixes the issue.
### Testing procedure
Flashing of e.g. the `cc2650-launchpad` with upstream OpenOCD should work again.
### Issues/PRs references
The change was added to https://github.com/RIOT-OS/RIOT/pull/19050 after testing the PR and before merging. I'm not sure if the fix never worked because of this, or if behavior of `target-export-variables` or GNU Make changed.
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Co-authored-by: Benjamin Valentin <benjamin.valentin@bht-berlin.de>
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
19485: sys/shell: Fix missing dependency r=aabadie a=maribu
### Contribution description
The shell commands depend on the shell module being use. This was already the case in KConfig, but was overlooked in the shell's `Makefile.dep`.
In addition, this uncovered that `tests/memarray` had a bogus dependency on shell commands without every using the shell.
### Testing procedure
Ideally binaries should not differ (except for debug section).
### Issues/PRs references
Split out of https://github.com/RIOT-OS/RIOT/pull/19483
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
The board no longer uses the `periph_usbdev_hs` module. Therefore, the maximum number of EPs used is that of the USB OTG FS peripheral, which is only 4. This is not sufficient for this test application since the board uses `stdio_cdc_acm`.
19397: drivers/usbdev_synopsys_dwc2: fix and reenable DMA mode r=benpicco a=gschorcht
### Contribution description
This PR fixes the DMA mode for all STM32 USB OTG HS cores (including that for STM32F4xx CID 1.xxx) and reenables it. It fixes remaining problems in issue #19359.
This PR includes also includes some changes that are needed to use the DMA mode:
- EP number is used as defined in CMSIS (if defined) for STM32
- `periph_usbdev_hs` feature is added in Kconfig
- `periph_usbdev_hs` feature is added in board definition of `stm32f429i-disc1`
- largest number of available EPs is used for STM32 instead of the smallest number (to be able to use all EPs of HS peripheral)
- `stm32f429i-disco` is removed from blacklist in `tests/usbus_cdc_ecm` since it uses the HS peripheral
### Testing procedure
The following tests should work
```python
USEMODULE=stdio_cdc_acm BOARD=stm32f429i-disc1 make -j8 -C tests/usbus_cdc_ecm flash
```
<details>
<summary>Test results</summary>
```python
[526755.875691] usb 1-2.2: new full-speed USB device number 106 using xhci_hcd
[526755.977853] usb 1-2.2: config 1 interface 3 altsetting 1 endpoint 0x84 has invalid maxpacket 512, setting to 64
[526755.977856] usb 1-2.2: config 1 interface 3 altsetting 1 endpoint 0x2 has invalid maxpacket 512, setting to 64
[526755.978762] usb 1-2.2: New USB device found, idVendor=1209, idProduct=7d01, bcdDevice= 1.00
[526755.978764] usb 1-2.2: New USB device strings: Mfr=3, Product=2, SerialNumber=4
[526755.978766] usb 1-2.2: Product: stm32f429i-disc1
[526755.978768] usb 1-2.2: Manufacturer: RIOT-os.org
[526755.978769] usb 1-2.2: SerialNumber: 7C156425A950A8EB
[526755.991190] cdc_acm 1-2.2:1.0: ttyACM1: USB ACM device
[526755.998131] cdc_ether 1-2.2:1.2 usb0: register 'cdc_ether' at usb-0000:00:14.0-2.2, CDC Ethernet Device, a6:f6:4a:85:1d:c9
[526756.044150] cdc_ether 1-2.2:1.2 enp0s20f0u2u2i2: renamed from usb0
```
</details>
```python
USEMODULE='stdio_cdc_acm periph_usbdev_hs_utmi' BOARD=stm32f723e-disco make -j8 -C tests/usbus_cdc_ecm flash
```
<details>
<summary>Test results</summary>
```python
[528733.480207] usb 1-4.3.4: reset high-speed USB device number 32 using xhci_hcd
[528733.707800] usb 1-4.4: new high-speed USB device number 111 using xhci_hcd
[528733.808257] usb 1-4.4: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11
[528733.808260] usb 1-4.4: config 1 interface 1 altsetting 0 bulk endpoint 0x1 has invalid maxpacket 64
[528733.808263] usb 1-4.4: config 1 interface 1 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 64
[528733.808642] usb 1-4.4: New USB device found, idVendor=1209, idProduct=7d01, bcdDevice= 1.00
[528733.808645] usb 1-4.4: New USB device strings: Mfr=3, Product=2, SerialNumber=4
[528733.808647] usb 1-4.4: Product: stm32f723e-disco
[528733.808649] usb 1-4.4: Manufacturer: RIOT-os.org
[528733.808651] usb 1-4.4: SerialNumber: A6BAC4E1B1E0806B
[528733.811988] cdc_acm 1-4.4:1.0: ttyACM1: USB ACM device
[528733.814456] cdc_ether 1-4.4:1.2 usb0: register 'cdc_ether' at usb-0000:00:14.0-4.4, CDC Ethernet Device, e6:75:97:3a:74:ba
[528733.854371] cdc_ether 1-4.4:1.2 enp0s20f0u4u4i2: renamed from usb0
```
</details>
```python
USEMODULE='stdio_cdc_acm periph_usbdev_hs_ulpi' BOARD=stm32f746g-disco make -j8 -C tests/usbus_cdc_ecm flash
```
<details>
<summary>Test results</summary>
```python
[529000.944482] usb 1-4.3.4: reset high-speed USB device number 32 using xhci_hcd
[529003.728260] usb 1-4.4: new high-speed USB device number 114 using xhci_hcd
[529003.833107] usb 1-4.4: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11
[529003.833111] usb 1-4.4: config 1 interface 1 altsetting 0 bulk endpoint 0x1 has invalid maxpacket 64
[529003.833113] usb 1-4.4: config 1 interface 1 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 64
[529003.833743] usb 1-4.4: New USB device found, idVendor=1209, idProduct=7d00, bcdDevice= 1.00
[529003.833747] usb 1-4.4: New USB device strings: Mfr=3, Product=2, SerialNumber=4
[529003.833749] usb 1-4.4: Product: stm32f746g-disco
[529003.833751] usb 1-4.4: Manufacturer: RIOT-os.org
[529003.833753] usb 1-4.4: SerialNumber: 66FE8934D1A363E0
[529003.837143] cdc_acm 1-4.4:1.0: ttyACM1: USB ACM device
[529003.839755] cdc_ether 1-4.4:1.2 usb0: register 'cdc_ether' at usb-0000:00:14.0-4.4, CDC Ethernet Device, 6a:88:1f:1f:b1:f0
[529003.879025] cdc_ether 1-4.4:1.2 enp0s20f0u4u4i2: renamed from usb0```
```
</details>
### Issues/PRs references
Fixes#19359
19416: cpu/rpx0xx/cmsis: Update vendor header files r=benpicco a=maribu
### Contribution description
Generated new vendor header files from upstream SVD files using:
./SVDConv "$PICO_SDK_DIR"/src/rp2040/hardware_regs/rp2040.svd \
--generate=header --fields=macro --fields=enum
Note: The missing `--fields=struct` flag resulted in the header no longer containing bit-fields to represent different fields within registers. While this would generally ease writing code, the RP2040 has the unpleasant feature of corrupting the remaining bits of the register when a write access that is not word-sized occurs in the memory mapped I/O area. This could happen e.g. when a bit field is byte-sized and byte-aligned.
### Testing procedure
No binary changes (hopefully).
### Issues/PRs references
This adds a few additional vendor defines, notably for USB. If anyone were to implement USB, this would be a requirement.
19418: cpu/gd32v: fix gpio_read in periph_gpio r=benpicco a=gschorcht
### Contribution description
This PR fixes a bug in `gpio_read` which made `gpio_read` completely unusable!
A small bug with big consequences. In `gpio_read` the combined port | pin_num parameter `pin` was used instead of the pin number `pin_num` for the call of `_pin_is_input`. This caused the problem that for example instead of accessing GPIOA->CTL0 with address 0x40010800, address 0x60018c00 was accessed. As a result, a pin was randomly detected as input or output and thus a result was arbitrarily returned. Approx. 50% of all inputs always returned LOW.
I found this error by coincidence when I tried to find out why the BOOT0 button on a Sipeed Longan Nano is not usable as a button in RIOT.
### Testing procedure
Flash `tests/periph_gpio`
```
BOARD=sipeed-longan-nano make -j8 -C tests/periph_gpio flash
```
and use commands
```
init_in 0 8
read 0 8
```
Without this PR, the pin is always LOW. With the PR, the pin should be HIGH when the BOOT button is pressed.
### Issues/PRs references
19419: boards/sipeed-longan-nano: add BOOT as user button r=benpicco a=gschorcht
### Contribution description
This PR makes the BOOT button usable as a user button.
### Testing procedure
The test requires PR #19418 to work.
Flash and test:
```
BOARD=sipeed-longan-nano make -j8 -C tests/saul flash term
```
The output
```
Dev: BOOT Type: SENSE_BTN
Data: 0
```
should change to
```
Dev: BOOT Type: SENSE_BTN
Data: 1
```
when the BOOT button is pressed.
### Issues/PRs references
Depends on PR #19418
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
19407: cpu/stm32/periph: Implement GPIO LL for STM32F1 without IRQ support (yet) r=gschorcht a=maribu
### Contribution description
This implements GPIO LL support for the STM32F1 in the first commit. IRQ support is added with https://github.com/RIOT-OS/RIOT/pull/19412.
This sneaks in a second commit replacing the `expect()` calls in `tests/periph_gpio_ll` with a trivial five-liner that doesn't `panic()`, so that stdio output will still be delivered on high level stdio implementations. The tests provides a lot of useful output to aid debugging, so its a great usability improvement if the test makes sure to actually deliver that output.
### Testing procedure
<details><summary><code>make -C tests/periph_gpio_ll BOARD=nucleo-f103rb flash term</code></summary>
```
2023-03-17 18:55:09,188 # Help: Press s to start test, r to print it is ready
s
2023-03-17 18:55:10,299 # START
2023-03-17 18:55:10,307 # main(): This is RIOT! (Version: 2023.04-devel-683-g9c3812-cpu/stm32/periph/gpio_ll)
2023-03-17 18:55:10,309 # Test / Hardware Details:
2023-03-17 18:55:10,310 # ========================
2023-03-17 18:55:10,311 # Cabling:
2023-03-17 18:55:10,313 # (INPUT -- OUTPUT)
2023-03-17 18:55:10,315 # P2.10 (PC10) -- P2.2 (PC2)
2023-03-17 18:55:10,318 # P2.12 (PC12) -- P2.3 (PC3)
2023-03-17 18:55:10,322 # Number of pull resistor values supported: 1
2023-03-17 18:55:10,325 # Number of drive strengths supported: 1
2023-03-17 18:55:10,328 # Number of slew rates supported: 3
2023-03-17 18:55:10,330 # Valid GPIO ports:
2023-03-17 18:55:10,332 # - PORT 0 (PORT A)
2023-03-17 18:55:10,333 # - PORT 1 (PORT B)
2023-03-17 18:55:10,335 # - PORT 2 (PORT C)
2023-03-17 18:55:10,336 # - PORT 3 (PORT D)
2023-03-17 18:55:10,338 # - PORT 4 (PORT E)
2023-03-17 18:55:10,338 #
2023-03-17 18:55:10,341 # Testing gpio_port_pack_addr()
2023-03-17 18:55:10,343 # =============================
2023-03-17 18:55:10,343 #
2023-03-17 18:55:10,344 # All OK
2023-03-17 18:55:10,344 #
2023-03-17 18:55:10,346 # Testing gpip_ng_init()
2023-03-17 18:55:10,348 # ======================
2023-03-17 18:55:10,348 #
2023-03-17 18:55:10,354 # Testing is_gpio_port_num_valid() is true for PORT_OUT and PORT_IN:
2023-03-17 18:55:10,354 #
2023-03-17 18:55:10,358 # Testing input configurations for PIN_IN_0:
2023-03-17 18:55:10,361 # Support for input with pull up: yes
2023-03-17 18:55:10,366 # state: in, pull: up, schmitt trigger: off, value: on
2023-03-17 18:55:10,369 # Support for input with pull down: yes
2023-03-17 18:55:10,374 # state: in, pull: down, schmitt trigger: off, value: off
2023-03-17 18:55:10,378 # Support for input with pull to bus level: no
2023-03-17 18:55:10,383 # Support for floating input (no pull resistors): yes
2023-03-17 18:55:10,388 # state: in, pull: none, schmitt trigger: off, value: off
2023-03-17 18:55:10,388 #
2023-03-17 18:55:10,392 # Testing output configurations for PIN_OUT_0:
2023-03-17 18:55:10,397 # Support for output (push-pull) with initial value of LOW: yes
2023-03-17 18:55:10,401 # state: out-pp, slew: slowest, value: off
2023-03-17 18:55:10,404 # Output is indeed LOW: yes
2023-03-17 18:55:10,408 # state: out-pp, slew: slowest, value: on
2023-03-17 18:55:10,411 # Output can be pushed HIGH: yes
2023-03-17 18:55:10,417 # Support for output (push-pull) with initial value of HIGH: yes
2023-03-17 18:55:10,420 # state: out-pp, slew: slowest, value: on
2023-03-17 18:55:10,424 # Output is indeed HIGH: yes
2023-03-17 18:55:10,430 # Support for output (open drain with pull up) with initial value of LOW: no
2023-03-17 18:55:10,437 # Support for output (open drain with pull up) with initial value of HIGH: no
2023-03-17 18:55:10,443 # Support for output (open drain) with initial value of LOW: yes
2023-03-17 18:55:10,449 # state: out-od, slew: slowest, pull: none, schmitt trigger: off, value: off
2023-03-17 18:55:10,452 # Output is indeed LOW: yes
2023-03-17 18:55:10,458 # Support for output (open drain) with initial value of HIGH: yes
2023-03-17 18:55:10,465 # state: out-od, slew: slowest, pull: none, schmitt trigger: off, value: on
2023-03-17 18:55:10,470 # state: in, pull: down, schmitt trigger: off, value: off
2023-03-17 18:55:10,474 # Output can indeed be pulled LOW: yes
2023-03-17 18:55:10,478 # state: in, pull: up, schmitt trigger: off, value: on
2023-03-17 18:55:10,483 # Output can indeed be pulled HIGH: yes
2023-03-17 18:55:10,488 # Support for output (open source) with initial value of LOW: no
2023-03-17 18:55:10,494 # Support for output (open source) with initial value of HIGH: no
2023-03-17 18:55:10,501 # Support for output (open source with pull up) with initial value of HIGH: no
2023-03-17 18:55:10,508 # Support for output (open source with pull up) with initial value of LOW: no
2023-03-17 18:55:10,511 # Support for disconnecting GPIO: yes
2023-03-17 18:55:10,515 # Output can indeed be pulled LOW: yes
2023-03-17 18:55:10,519 # Output can indeed be pulled HIGH: yes
2023-03-17 18:55:10,519 #
2023-03-17 18:55:10,523 # Testing Reading/Writing GPIO Ports
2023-03-17 18:55:10,526 # ==================================
2023-03-17 18:55:10,526 #
2023-03-17 18:55:10,529 # testing initial value of 0 after init
2023-03-17 18:55:10,531 # ...OK
2023-03-17 18:55:10,535 # testing setting both outputs_optional simultaneously
2023-03-17 18:55:10,537 # ...OK
2023-03-17 18:55:10,541 # testing clearing both outputs_optional simultaneously
2023-03-17 18:55:10,543 # ...OK
2023-03-17 18:55:10,547 # testing toggling first output (0 --> 1)
2023-03-17 18:55:10,548 # ...OK
2023-03-17 18:55:10,552 # testing toggling first output (1 --> 0)
2023-03-17 18:55:10,553 # ...OK
2023-03-17 18:55:10,557 # testing toggling second output (0 --> 1)
2023-03-17 18:55:10,558 # ...OK
2023-03-17 18:55:10,562 # testing toggling second output (1 --> 0)
2023-03-17 18:55:10,563 # ...OK
2023-03-17 18:55:10,569 # testing setting first output and clearing second with write
2023-03-17 18:55:10,570 # ...OK
2023-03-17 18:55:10,575 # testing setting second output and clearing first with write
2023-03-17 18:55:10,576 # ...OK
2023-03-17 18:55:10,580 # All input/output operations worked as expected
2023-03-17 18:55:10,580 #
2023-03-17 18:55:10,580 #
2023-03-17 18:55:10,582 # TEST SUCCEEDED
2023-03-17 18:55:10,588 # { "threads": [{ "name": "main", "stack_size": 1536, "stack_used": 456 }]}
```
</details>
<details><summary><code>make -C tests/bench_periph_gpio_ll BOARD=nucleo-f103rb flash term</code></summary>
```
2023-03-17 18:55:42,192 # Help: Press s to start test, r to print it is ready
s
2023-03-17 18:55:44,616 # START
2023-03-17 18:55:44,624 # main(): This is RIOT! (Version: 2023.04-devel-683-g9c3812-cpu/stm32/periph/gpio_ll)
2023-03-17 18:55:44,624 #
2023-03-17 18:55:44,626 # Benchmarking GPIO APIs
2023-03-17 18:55:44,628 # ======================
2023-03-17 18:55:44,628 #
2023-03-17 18:55:44,632 # estimating loop overhead for compensation
2023-03-17 18:55:44,635 # -----------------------------------------
2023-03-17 18:55:44,642 # 4168 us for 50000 iterations
2023-03-17 18:55:44,642 #
2023-03-17 18:55:44,647 # periph/gpio: Using 2x gpio_set() and 2x gpio_clear()
2023-03-17 18:55:44,651 # ---------------------------------------------------
2023-03-17 18:55:44,706 # 50000 iterations took 45840 us (50008 us uncompensated)
2023-03-17 18:55:44,713 # Two square waves pins at 1090750 Hz ( 999840 Hz uncompensated)
2023-03-17 18:55:44,719 # ~66 CPU cycles per square wave period (~72 cycles uncompensated)
2023-03-17 18:55:44,719 # :'-(
2023-03-17 18:55:44,719 #
2023-03-17 18:55:44,724 # periph/gpio_ll: Using gpio_ll_set() and gpio_ll_clear()
2023-03-17 18:55:44,729 # -------------------------------------------------------
2023-03-17 18:55:44,738 # 50000 iterations took 695 us (4863 us uncompensated)
2023-03-17 18:55:44,745 # Two square waves pins at 71942446 Hz ( 10281719 Hz uncompensated)
2023-03-17 18:55:44,750 # ~1 CPU cycles per square wave period (~7 cycles uncompensated)
2023-03-17 18:55:44,751 # :-D
2023-03-17 18:55:44,751 #
2023-03-17 18:55:44,755 # periph/gpio: Using 4x gpio_toggle()
2023-03-17 18:55:44,757 # -----------------------------------
2023-03-17 18:55:44,965 # 50000 iterations took 198646 us (202814 us uncompensated)
2023-03-17 18:55:44,972 # Two square waves pins at 251704 Hz ( 246531 Hz uncompensated)
2023-03-17 18:55:44,977 # ~286 CPU cycles per square wave period (~292 cycles uncompensated)
2023-03-17 18:55:44,978 # :'-(
2023-03-17 18:55:44,978 #
2023-03-17 18:55:44,982 # periph/gpio_ll: Using 2x gpio_ll_toggle()
2023-03-17 18:55:44,985 # -----------------------------------------
2023-03-17 18:55:45,010 # 50000 iterations took 15972 us (20140 us uncompensated)
2023-03-17 18:55:45,017 # Two square waves pins at 3130478 Hz ( 2482621 Hz uncompensated)
2023-03-17 18:55:45,023 # ~23 CPU cycles per square wave period (~29 cycles uncompensated)
2023-03-17 18:55:45,023 # :'-(
2023-03-17 18:55:45,023 #
2023-03-17 18:55:45,026 # periph/gpio: Using 4x gpio_write()
2023-03-17 18:55:45,029 # ----------------------------------
2023-03-17 18:55:45,097 # 50000 iterations took 58345 us (62513 us uncompensated)
2023-03-17 18:55:45,103 # Two square waves pins at 856971 Hz ( 799833 Hz uncompensated)
2023-03-17 18:55:45,109 # ~84 CPU cycles per square wave period (~90 cycles uncompensated)
2023-03-17 18:55:45,109 # :'-(
2023-03-17 18:55:45,110 #
2023-03-17 18:55:45,113 # periph/gpio_ll: Using 2x gpio_ll_write()
2023-03-17 18:55:45,117 # ----------------------------------------
2023-03-17 18:55:45,128 # 50000 iterations took 2777 us (6945 us uncompensated)
2023-03-17 18:55:45,135 # Two square waves pins at 18005041 Hz ( 7199424 Hz uncompensated)
2023-03-17 18:55:45,141 # ~4 CPU cycles per square wave period (~10 cycles uncompensated)
2023-03-17 18:55:45,141 # :-)
2023-03-17 18:55:45,141 #
2023-03-17 18:55:45,141 #
2023-03-17 18:55:45,142 # TEST SUCCEEDED
2023-03-17 18:55:45,149 # { "threads": [{ "name": "main", "stack_size": 1536, "stack_used": 448 }]}
```
</details>
### Issues/PRs references
None
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Use a custom expect() that just spins in an endless loop instead of
panicking. The test isn't run automatically anyway, as it requires
connecting two GPIOs with jumper wires; but when run manually it is
helpful to not kill RIOT to also get the stdio output of the exact
point where the test fails (e.g. USB CDC ACM doesn't like panic()).
