19811: boards: add ESP32-S3-Box support r=gschorcht a=gschorcht
### Contribution description
This PR provides the support for the [ESP32-S3-Box](https://github.com/espressif/esp-box).
### Testing procedure
The board has been tested with all basic tests for supported hardware including `tests/drivers/ili9341`:
- [x] tests/drivers/ili9341
- [x] tests/periph/gpio
- [x] tests/periph/i2c
- [x] tests/periph/spi
- [x] tests/periph/uart
- [x] tests/sys/usbus_cdc_ecm
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
This module provides no more than the correct configuration parameters
for the `w5100` driver using the Arduino I/O mapping features. But
by doing so, it will work out of the box with every mechanically and
electrically compatible board for which the Arduino I/O mapping
features are implemented.
19487: nanocoap: implement extended tokens (RFC 8974) r=benpicco a=benpicco
19808: boards: add ESP32-S3-USB-OTG support r=benpicco a=gschorcht
### Contribution description
This PR provides the support for the [ESP32-S3-USB-OTG](https://docs.espressif.com/projects/espressif-esp-dev-kits/en/latest/esp32s3/esp32-s3-usb-otg/user_guide.html) board.
The SD card can only be used in SPI mode at the moment. As soon as PR #19786 is merged, the SD/MMC support can be enabled and the SD card can then be used in SD mode with 4-bit data bus width.
The display uses uses the ST7789 driver IC that is compatible with the ST7735. For that purpose the ST7735 driver is extended by a pseudomodule definition `st7789` for the ST7789 which is enabled by the board and enables automatically the `st7789` (e57c48a33ee2a869c15603788e5306ba066f91cf). Vise versa, board's `Makefile.dep` enables automatically the `st7789` pseudomodule if the `st7735` is used. The pseudomodule `st7789` is just used to increase the upper limit for supported lines. This change is also part of PR #19807.
~The PR includes a very small documentation fix for ESP32-S3-DevKit board that was noticed during the development of this board definition (1155b6ac1b8efa39d8a0bd7150e602095159fdc1).~
### Testing procedure
The board has been tested with all basic tests for supported hardware including `tests/driver/st3375`:
- [x] tests/drivers/st3375
- [x] tests/periph/gpio
- [x] tests/periph/pwm
- [x] tests/periph/spi
- [x] tests/periph/uart
- [x] tests/sys/usbus_cdc_ecm
### Issues/PRs references
Co-authored-by: Benjamin Valentin <benpicco@beuth-hochschule.de>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19804: cpu/nrf{53,9160}: add periph_rtt support r=benpicco a=dylad
### Contribution description
This PR enables support for `periph_rtt` on both nRF9160 and nRF53.
This PR is based on #19803
I was only able to test on nrf5340dk-app as I don't have access to any nrf9160-based board.
Here is `test/periph/rtt` output for reference on `nrf5340dk-app`:
### Testing procedure
flash `tests/periph/rtt` on `nrf9160dk` or `nrf5340dk-app` and check the results.
```
s
2023-07-06 16:11:16,471 # START
2023-07-06 16:11:16,479 # main(): This is RIOT! (Version: 2023.07-devel-765-g02c65-cpu/nrf53/add_rtt_support)
2023-07-06 16:11:16,480 #
2023-07-06 16:11:16,482 # RIOT RTT low-level driver test
2023-07-06 16:11:16,483 # RTT configuration:
2023-07-06 16:11:16,485 # RTT_MAX_VALUE: 0x00ffffff
2023-07-06 16:11:16,487 # RTT_FREQUENCY: 1024
2023-07-06 16:11:16,487 #
2023-07-06 16:11:16,494 # Testing the tick conversion (with rounding if RTT_FREQUENCY is not power of 2)
2023-07-06 16:11:16,498 # Trying to convert 1 to seconds and back
2023-07-06 16:11:16,501 # Trying to convert 256 to seconds and back
2023-07-06 16:11:16,505 # Trying to convert 65536 to seconds and back
2023-07-06 16:11:16,509 # Trying to convert 16777216 to seconds and back
2023-07-06 16:11:16,514 # Trying to convert 2147483648 to seconds and back
2023-07-06 16:11:16,514 # All ok
2023-07-06 16:11:16,514 #
2023-07-06 16:11:16,517 # Initializing the RTT driver
2023-07-06 16:11:16,835 # This test will now display 'Hello' every 5 seconds
2023-07-06 16:11:16,835 #
2023-07-06 16:11:16,836 # RTT now: 4
2023-07-06 16:11:16,840 # Setting initial alarm to now + 5 s (5124)
2023-07-06 16:11:16,841 # rtt_get_alarm() PASSED
2023-07-06 16:11:16,846 # Done setting up the RTT, wait for many Hellos
2023-07-06 16:11:16,852 # { "threads": [{ "name": "main", "stack_size": 1536, "stack_used": 404 }]}
2023-07-06 16:11:21,833 # Hello
2023-07-06 16:11:26,831 # Hello
2023-07-06 16:11:31,830 # Hello
2023-07-06 16:11:36,828 # Hello
2023-07-06 16:11:41,826 # Hello
2023-07-06 16:11:46,825 # Hello
2023-07-06 16:11:51,823 # Hello
2023-07-06 16:11:56,821 # Hello
2023-07-06 16:12:01,821 # Hello
2023-07-06 16:12:06,819 # Hello
2023-07-06 16:12:11,817 # Hello
2023-07-06 16:12:16,815 # Hello
2023-07-06 16:12:21,813 # Hello
2023-07-06 16:12:26,811 # Hello
```
### Issues/PRs references
based on #19803
19807: boards/esp32s2-lilygo-ttgo-t8: fix display configuration r=benpicco a=gschorcht
### Contribution description
This PR fixes the display configuration for the ESP32-S2 LilyGO TTGO T8 (also known as LilyGo T-Display S2) which uses a ST7789 as display driver IC that is compatible with the ST7735.
For that purpose the ST7735 driver is extended by a pseudomodule definition `st7789` for the ST7789 which is enabled by the board and enables automatically the `st7789` (f57b6b70b8). Vise versa, board's `Makefile.dep` enables automatically the `st7789` pseudomodule if the `st7735` is used. The pseudomodule `st7789` is just used to increase the upper limit for supported lines.
### Testing procedure
```
BOARD=esp32s2-lilygo-ttgo-t8 make -C tests/drivers/st7735/ flash
```
should work:
### Issues/PRs references
19809: cpu/nrf53: add usbdev support r=benpicco a=dylad
### Contribution description
This PR enables `periph_usbdev` support on nRF5340DK-app board. Since the IP is the same as nRF52, the driver and its related data and structs were moved from `cpu/nrf52` to `cpu/nrf5x_common`
### Testing procedure
Test any USBUS related test application on `nrf5340dk-app`
`CFLAGS='-DSECTOR_COUNT=64' USEMODULE='mtd_emulated' make BOARD=nrf5340dk-app -C tests/sys/usbus_msc flash`
dmesg output:
```
[ 7466.262760] usb 1-2.1: new full-speed USB device number 16 using xhci_hcd
[ 7466.483916] usb 1-2.1: New USB device found, idVendor=1209, idProduct=7d01, bcdDevice= 1.00
[ 7466.483925] usb 1-2.1: New USB device strings: Mfr=3, Product=2, SerialNumber=4
[ 7466.483928] usb 1-2.1: Product: nrf5340dk-app
[ 7466.483931] usb 1-2.1: Manufacturer: RIOT-os.org
[ 7466.483933] usb 1-2.1: SerialNumber: AD0FD4AE806080C2
[ 7466.487010] usb-storage 1-2.1:1.0: USB Mass Storage device detected
[ 7466.487348] scsi host2: usb-storage 1-2.1:1.0
[ 7467.516789] scsi 2:0:0:0: Direct-Access RIOT-OS RIOT_MSC_DISK 1.0 PQ: 0 ANSI: 1
[ 7467.517152] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 7467.517501] sd 2:0:0:0: [sdd] 64 512-byte logical blocks: (32.8 kB/32.0 KiB)
[ 7467.517732] sd 2:0:0:0: [sdd] Write Protect is off
[ 7467.517733] sd 2:0:0:0: [sdd] Mode Sense: 03 00 00 00
[ 7467.517906] sd 2:0:0:0: [sdd] No Caching mode page found
[ 7467.517910] sd 2:0:0:0: [sdd] Assuming drive cache: write through
[ 7467.532159] sd 2:0:0:0: [sdd] Attached SCSI removable disk
```
I also tested `tests/sys/usbus_cdc_ecm` and `tests/sys/usbus/usbus_hid` succesfully.
### Issues/PRs references
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19791: makefiles/arch/riscv.inc.mk: speed up toolchain detection r=benpicco a=maribu
### Contribution description
- Use a sane (a.k.a. simply expanded) variable for the `$(TARGET_ARCH)` instead of an insane (a.k.a. recursive expended) variable - The toolchain detection will now happen only once, rather than each and every time `$(TARGET_ARCH)` is referenced
- Use a single call to `which` rather than one per possible target triple
Fixes https://github.com/RIOT-OS/RIOT/issues/19788
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@posteo.net>
19789: cpu/nrf5x/periph/wdt: enable support for nRF53/nRF9160 r=benpicco a=dylad
### Contribution description
This PR enables support for the watchdog driver on nRF53.
This MCU has two watchdog peripherals, for now, it only uses the first one.
The use of the second watchdog can be add in a followup PR later.
### Testing procedure
Flash and play with `tests/periph/wdt` application.
### Issues/PRs references
None.
19796: boards/b_u585i_ iot02a/periph usbdev r=benpicco a=gschorcht
### Contribution description
This PR adds the USB OTG support for STM32U5 and the `b_u585i_iot02a` board.
This PR includes PR #19795 since it uses directly the changes made in PR #19795.
### Testing procedure
Compile and flash
```
BOARD=b-u585i-iot02a make -C tests/sys/usbus_cdc_ecm/ flash term
```
Use the `sudo dmesg` command to get the kernel messages.
```pyhon
[766948.556645] usb 1-2.2: new full-speed USB device number 108 using xhci_hcd
[766948.658688] usb 1-2.2: New USB device found, idVendor=1209, idProduct=7d00, bcdDevice= 1.00
[766948.658696] usb 1-2.2: New USB device strings: Mfr=3, Product=2, SerialNumber=4
[766948.658699] usb 1-2.2: Product: b-u585i-iot02a
[766948.658702] usb 1-2.2: Manufacturer: RIOT-os.org
[766948.658704] usb 1-2.2: SerialNumber: AA140057DA41D467
[766948.668681] cdc_ether 1-2.2:1.0 usb0: register 'cdc_ether' at usb-0000:00:14.0-2.2, CDC Ethernet Device, ea:dc:44:71:d9:24
[766948.743250] cdc_ether 1-2.2:1.0 enxeadc4471d924: renamed from usb0
```
Use the `ifconfig` command on the node to determine the IPv6 LLUA and ping the node.
```
ping6 -c 3 fe80::e8dc:44ff:fe71:c524%enxeadc4471d924
PING fe80::e8dc:44ff:fe71:c524%enxeadc4471d924(fe80::e8dc:44ff:fe71:c524%enxeadc4471d924) 56 data bytes
64 bytes from fe80::e8dc:44ff:fe71:c524%enxeadc4471d924: icmp_seq=1 ttl=64 time=0.523 ms
64 bytes from fe80::e8dc:44ff:fe71:c524%enxeadc4471d924: icmp_seq=2 ttl=64 time=0.546 ms
64 bytes from fe80::e8dc:44ff:fe71:c524%enxeadc4471d924: icmp_seq=3 ttl=64 time=0.599 ms
```
### Issues/PRs references
Includes PR #19795
19802: cpu/nrf53: enable flashpage support r=benpicco a=dylad
### Contribution description
This PR enables flashpage support on nRF53 family.
The peripheral is identical to nRF52, just add the flashpage configuration and enable the module in both Makefiles.features and Kconfig.
### Testing procedure
run `/tests/periph/flashpage` on `nrf5340dk-app`
output of `make BOARD=nrf5340dk-app flash test`
```
/home/dylan/work/RIOT/dist/tools/pyterm/pyterm -p "/dev/ttyACM0" -b "115200" --no-reconnect --noprefix --no-repeat-command-on-empty-line
Twisted not available, please install it if you want to use pyterm's JSON capabilities
Connect to serial port /dev/ttyACM0
Welcome to pyterm!
Type '/exit' to exit.
>
>
test_last_raw
> test_last_raw
wrote raw short buffer to last flash page
> help
help
Command Description
---------------------------------------
info Show information about pages
dump Dump the selected page to STDOUT
dump_local Dump the local page buffer to STDOUT
read Copy the given page to the local page buffer and dump to STDOUT
write Write the local page buffer to the given page
write_raw Write (ASCII, max 64B) data to the given address
erase Erase the given page buffer
edit Write bytes to the local page buffer
test Write and verify test pattern
test_last_pagewise Write and verify test pattern on last page available
test_last_pagewise
test_reserved_pagewise Write and verify short write on reserved page
test_last_raw Write and verify raw short write on last page available
> test_last_pagewise
wrote local page buffer to last flash page
> help
help
Command Description
---------------------------------------
info Show information about pages
dump Dump the selected page to STDOUT
dump_local Dump the local page buffer to STDOUT
read Copy the given page to the local page buffer and dump to STDOUT
write Write the local page buffer to the given page
write_raw Write (ASCII, max 64B) data to the given address
erase Erase the given page buffer
edit Write bytes to the local page buffer
test Write and verify test pattern
test_last_pagewise Write and verify test pattern on last page available
test_reserved_pagewise Write and verify short write on reserved page
test_reserved_pagewise
test_last_raw Write and verify raw short write on last page available
> test_reserved_pagewise
Reserved page num: 5
Since the last firmware update this test has been run 0 times
wrote local page buffer to reserved flash page
When running on a bootloader, as an extra check, try restarting the board and check whether this application still comes up.
> help
help
Command Description
---------------------------------------
info Show information about pages
dump Dump the selected page to STDOUT
dump_local Dump the local page buffer to STDOUT
read Copy the given page to the local page buffer and dump to STDOUT
write Write the local page buffer to the given page
write_raw Write (ASCII, max 64B) data to the given address
erase Erase the given page buffer
edit Write bytes to the local page buffer
test Write and verify test pattern
test_last_pagewise Write and verify test pattern on last page available
test_reserved_pagewise Write and verify short write on reserved page
test_last_raw Write and verify raw short write on last page available
>
make : on quitte le répertoire « /home/dylan/work/RIOT/tests/periph/flashpage »
```
### Issues/PRs references
None.
19803: cpu/nrf5x_common: rework LFCLK source selection r=benpicco a=dylad
### Contribution description
This PR changes the source selection of LFCLK for all nRF families.
This idea is to use the values provided by Nordic vendor files to properly populate the source of the LFCLK. Then setup a per CPU check to ensure the value provided at board level is fine. In the end, the LFCLK source selection is a mere assignment.
The selection of the LFCLK source is still done at board level. I also add a bit of documentation to help users to select another value if needed.
I'll provide in a followup PR, `periph_rtt` support for both nRF9160 and nRF53.
### Testing procedure
CI should be enough I think. Otherwise, one can ran tests/periph/rtt on any nRF51-based board and any nRF52-based board.
You can also change the LFCLK source at board level to ensure the guards are doing their jobs.
### Issues/PRs references
None.
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Otherwise the function will only displays the first 256 ASCII representation of the bytes in a loop
Signed-off-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
The current ISR implementation for AVR8 requires use of
avr8_[enter/exit]_isr pair which add some boilerplate on code.
This add AVR8_ISR which clean-up the code and make it simpler
and hides any schedule detail from the user perspective.
This is a preparation for future scheduling and irq optimizations.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The thread_yield_higher is a normal functions. However it has a non
regular return instruction which is useless. This remove the useless
return on thread_yield_higher to save flash bytes.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The avr8_state variable uses bit operation to set/clear the state. This
rework avr8_state to use increment/decrement instead. It introduce the
use of General Purpose IO Register 1 (GPIOR1) when available.
This is a preparation for future scheduling and irq optimizations.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The avr8_state store state information used to determine scheduling
and uart irq. This move all uart irq states to avr8_state_uart
variable. It introduce the use of General Purpose IO Register 0
(GPIOR0) when available and now all uarts from xmega can be used.
This is a preparation for future scheduling and irq optimizations.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
19797: Makefile.include: don't use target lstfile implicitly r=maribu a=gschorcht
### Contribution description
This PR reverts a part of PR #19745. It removes the `$(LSTFILE)` from the `BUILD_FILES` variable so that the `.lst` file isn't generated implicitly. If the `.lst` file is needed, it can be generated with `lstfile` target.
**Background**
The compilation time increased a lot with PR #19745. The reason is that the generation of the `.lst` file seems to be time-consuming. For example, on an Intel(R) Core(TM) i7-8550U CPU @ 1.80GHz` with 8 cores and a SSD, it takes about 15 seconds for a complex application such as `tests/sys/usbus_msc` for a STM32F7 MCU.
Therefore, the compilation time for
```
BOARD=stm32f723e-disco make -j8 -C tests/sys/usbus_msc
```
increased from about 1 sec to about 16 seconds (all source files were already compiled).
Even for a small application
```
BOARD=stm32f723e-disco make -j8 -C tests/sys/shell
```
the compilation time increased from about 1 sec to about 10 seconds.
### Testing procedure
Green CI
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
