After cleaning up the default config of SPI, this commit cleans up the configuration for `sipeed-longan-nano` a bit:
- PA4 is no longer used as default CS for `SPI_DEV(1)`
- At least one DAC channel PA4 is always available if DAC is used.
- PA4 is always available as ADC channel if DAC is not used.
- The order of ADC and DAC channels has been changed accordingly.
This commit includes the following cleanups:
- The macros `I2C_DEV_1_USED` and `SPI_DEV_1_USED` are now used with the values 0 and 1. This allows to enable but also to disable the second interface even if the board definition enables it by default.
- The second I2C device `I2C_DEV(1)` and the second SPI device `SPI_DEV(1)` are now disabled by default.
- The second SPI device `SPI_DEV(1)` now uses PB5 as default CS signal instead of PA4 to keep PA4 free for ADC or DAC even if `SPI_DEV(1)` is used, for example for the TFT display.
This commit introduces a separate board definition based on the `sipeed-longan-nano` board definition for the TFT version of the Sipeed Longan Nano board.
19798: cpu/nrf53: add I2C and SPI support r=benpicco a=dylad
### Contribution description
This PR provides support for nRF53 SPI and I2C.
It also moves common structs from each nRF CPU folder to `cpu/nrf5x_common` to avoid duplication.
Moreover, since nRF9160 and nRF5340 have shared IRQ for UART/SPI/I2C. Both this families now use a common file to register and manage these interrupts. Note that nRF9160 have different name for its interrupts than nRF5340 but they have the same purpose.
### Testing procedure
Since some structs were moved around, I think this PR should be carefully tested against nRF52, nRF53 and nRF9160 to avoid any issues.
On nRF5340DK-APP, SPI can be tested with its onboard SPI flash.
### Issues/PRs references
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
19806: ztimer/periodic: remove timer on init if already running r=kaspar030 a=benpicco
19814: boards/sipeed-longan-nano: revert default to variant with TFT r=benpicco a=gschorcht
### Contribution description
This PR reverts commit 69fb00bdfa to fix CI compilation.
### Testing procedure
Green CI with full build.
### Issues/PRs references
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@posteo.net>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19764: drivers/shield_w5100: add module for the W5100 Ethernet Shield r=benpicco a=maribu
### Contribution description
This module provides no more than the correct configuration parameters for the `w5100` driver using the Arduino I/O mapping features. But by doing so, it will work out of the box with every mechanically and electrically compatible board for which the Arduino I/O mapping features are implemented.
19781: cpu/nrf{53,9160}: add pwm support r=benpicco a=dylad
### Contribution description
This PR moves the nRF52 PWM driver to `cpu/nrf5x_common` to allow nRF9160 and nRF53 to use this driver.
IP is identical on these families.
I didn't test on nRF9160DK and I didn't test if there is any regression on nRF52-based board as I don't have any so tests are welcome !
However it works fine on nRF53-based board.
### Testing procedure
Flash the `tests/periph/pwm` test application on `nrf5340dk` or `nrf9160dk`.
You can then use the `osci` command to make the onboard LEDs "breath".
You can also attach an oscilloscope and/or logic analyzer to watch the signal.
### Issues/PRs references
~~Based on #19769~~
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@posteo.net>
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Co-authored-by: dylad <dylan.laduranty@mesotic.com>
Without KConfig presence of the TFT is assumed in anycase, with KConfig
it is optional. This turns the opt-in into an opt-out to match behavior
with make by default, fixing the nightly breakage.
19811: boards: add ESP32-S3-Box support r=gschorcht a=gschorcht
### Contribution description
This PR provides the support for the [ESP32-S3-Box](https://github.com/espressif/esp-box).
### Testing procedure
The board has been tested with all basic tests for supported hardware including `tests/drivers/ili9341`:
- [x] tests/drivers/ili9341
- [x] tests/periph/gpio
- [x] tests/periph/i2c
- [x] tests/periph/spi
- [x] tests/periph/uart
- [x] tests/sys/usbus_cdc_ecm
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19487: nanocoap: implement extended tokens (RFC 8974) r=benpicco a=benpicco
19808: boards: add ESP32-S3-USB-OTG support r=benpicco a=gschorcht
### Contribution description
This PR provides the support for the [ESP32-S3-USB-OTG](https://docs.espressif.com/projects/espressif-esp-dev-kits/en/latest/esp32s3/esp32-s3-usb-otg/user_guide.html) board.
The SD card can only be used in SPI mode at the moment. As soon as PR #19786 is merged, the SD/MMC support can be enabled and the SD card can then be used in SD mode with 4-bit data bus width.
The display uses uses the ST7789 driver IC that is compatible with the ST7735. For that purpose the ST7735 driver is extended by a pseudomodule definition `st7789` for the ST7789 which is enabled by the board and enables automatically the `st7789` (e57c48a33ee2a869c15603788e5306ba066f91cf). Vise versa, board's `Makefile.dep` enables automatically the `st7789` pseudomodule if the `st7735` is used. The pseudomodule `st7789` is just used to increase the upper limit for supported lines. This change is also part of PR #19807.
~The PR includes a very small documentation fix for ESP32-S3-DevKit board that was noticed during the development of this board definition (1155b6ac1b8efa39d8a0bd7150e602095159fdc1).~
### Testing procedure
The board has been tested with all basic tests for supported hardware including `tests/driver/st3375`:
- [x] tests/drivers/st3375
- [x] tests/periph/gpio
- [x] tests/periph/pwm
- [x] tests/periph/spi
- [x] tests/periph/uart
- [x] tests/sys/usbus_cdc_ecm
### Issues/PRs references
Co-authored-by: Benjamin Valentin <benpicco@beuth-hochschule.de>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19804: cpu/nrf{53,9160}: add periph_rtt support r=benpicco a=dylad
### Contribution description
This PR enables support for `periph_rtt` on both nRF9160 and nRF53.
This PR is based on #19803
I was only able to test on nrf5340dk-app as I don't have access to any nrf9160-based board.
Here is `test/periph/rtt` output for reference on `nrf5340dk-app`:
### Testing procedure
flash `tests/periph/rtt` on `nrf9160dk` or `nrf5340dk-app` and check the results.
```
s
2023-07-06 16:11:16,471 # START
2023-07-06 16:11:16,479 # main(): This is RIOT! (Version: 2023.07-devel-765-g02c65-cpu/nrf53/add_rtt_support)
2023-07-06 16:11:16,480 #
2023-07-06 16:11:16,482 # RIOT RTT low-level driver test
2023-07-06 16:11:16,483 # RTT configuration:
2023-07-06 16:11:16,485 # RTT_MAX_VALUE: 0x00ffffff
2023-07-06 16:11:16,487 # RTT_FREQUENCY: 1024
2023-07-06 16:11:16,487 #
2023-07-06 16:11:16,494 # Testing the tick conversion (with rounding if RTT_FREQUENCY is not power of 2)
2023-07-06 16:11:16,498 # Trying to convert 1 to seconds and back
2023-07-06 16:11:16,501 # Trying to convert 256 to seconds and back
2023-07-06 16:11:16,505 # Trying to convert 65536 to seconds and back
2023-07-06 16:11:16,509 # Trying to convert 16777216 to seconds and back
2023-07-06 16:11:16,514 # Trying to convert 2147483648 to seconds and back
2023-07-06 16:11:16,514 # All ok
2023-07-06 16:11:16,514 #
2023-07-06 16:11:16,517 # Initializing the RTT driver
2023-07-06 16:11:16,835 # This test will now display 'Hello' every 5 seconds
2023-07-06 16:11:16,835 #
2023-07-06 16:11:16,836 # RTT now: 4
2023-07-06 16:11:16,840 # Setting initial alarm to now + 5 s (5124)
2023-07-06 16:11:16,841 # rtt_get_alarm() PASSED
2023-07-06 16:11:16,846 # Done setting up the RTT, wait for many Hellos
2023-07-06 16:11:16,852 # { "threads": [{ "name": "main", "stack_size": 1536, "stack_used": 404 }]}
2023-07-06 16:11:21,833 # Hello
2023-07-06 16:11:26,831 # Hello
2023-07-06 16:11:31,830 # Hello
2023-07-06 16:11:36,828 # Hello
2023-07-06 16:11:41,826 # Hello
2023-07-06 16:11:46,825 # Hello
2023-07-06 16:11:51,823 # Hello
2023-07-06 16:11:56,821 # Hello
2023-07-06 16:12:01,821 # Hello
2023-07-06 16:12:06,819 # Hello
2023-07-06 16:12:11,817 # Hello
2023-07-06 16:12:16,815 # Hello
2023-07-06 16:12:21,813 # Hello
2023-07-06 16:12:26,811 # Hello
```
### Issues/PRs references
based on #19803
19807: boards/esp32s2-lilygo-ttgo-t8: fix display configuration r=benpicco a=gschorcht
### Contribution description
This PR fixes the display configuration for the ESP32-S2 LilyGO TTGO T8 (also known as LilyGo T-Display S2) which uses a ST7789 as display driver IC that is compatible with the ST7735.
For that purpose the ST7735 driver is extended by a pseudomodule definition `st7789` for the ST7789 which is enabled by the board and enables automatically the `st7789` (f57b6b70b8). Vise versa, board's `Makefile.dep` enables automatically the `st7789` pseudomodule if the `st7735` is used. The pseudomodule `st7789` is just used to increase the upper limit for supported lines.
### Testing procedure
```
BOARD=esp32s2-lilygo-ttgo-t8 make -C tests/drivers/st7735/ flash
```
should work:
### Issues/PRs references
19809: cpu/nrf53: add usbdev support r=benpicco a=dylad
### Contribution description
This PR enables `periph_usbdev` support on nRF5340DK-app board. Since the IP is the same as nRF52, the driver and its related data and structs were moved from `cpu/nrf52` to `cpu/nrf5x_common`
### Testing procedure
Test any USBUS related test application on `nrf5340dk-app`
`CFLAGS='-DSECTOR_COUNT=64' USEMODULE='mtd_emulated' make BOARD=nrf5340dk-app -C tests/sys/usbus_msc flash`
dmesg output:
```
[ 7466.262760] usb 1-2.1: new full-speed USB device number 16 using xhci_hcd
[ 7466.483916] usb 1-2.1: New USB device found, idVendor=1209, idProduct=7d01, bcdDevice= 1.00
[ 7466.483925] usb 1-2.1: New USB device strings: Mfr=3, Product=2, SerialNumber=4
[ 7466.483928] usb 1-2.1: Product: nrf5340dk-app
[ 7466.483931] usb 1-2.1: Manufacturer: RIOT-os.org
[ 7466.483933] usb 1-2.1: SerialNumber: AD0FD4AE806080C2
[ 7466.487010] usb-storage 1-2.1:1.0: USB Mass Storage device detected
[ 7466.487348] scsi host2: usb-storage 1-2.1:1.0
[ 7467.516789] scsi 2:0:0:0: Direct-Access RIOT-OS RIOT_MSC_DISK 1.0 PQ: 0 ANSI: 1
[ 7467.517152] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 7467.517501] sd 2:0:0:0: [sdd] 64 512-byte logical blocks: (32.8 kB/32.0 KiB)
[ 7467.517732] sd 2:0:0:0: [sdd] Write Protect is off
[ 7467.517733] sd 2:0:0:0: [sdd] Mode Sense: 03 00 00 00
[ 7467.517906] sd 2:0:0:0: [sdd] No Caching mode page found
[ 7467.517910] sd 2:0:0:0: [sdd] Assuming drive cache: write through
[ 7467.532159] sd 2:0:0:0: [sdd] Attached SCSI removable disk
```
I also tested `tests/sys/usbus_cdc_ecm` and `tests/sys/usbus/usbus_hid` succesfully.
### Issues/PRs references
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19789: cpu/nrf5x/periph/wdt: enable support for nRF53/nRF9160 r=benpicco a=dylad
### Contribution description
This PR enables support for the watchdog driver on nRF53.
This MCU has two watchdog peripherals, for now, it only uses the first one.
The use of the second watchdog can be add in a followup PR later.
### Testing procedure
Flash and play with `tests/periph/wdt` application.
### Issues/PRs references
None.
19796: boards/b_u585i_ iot02a/periph usbdev r=benpicco a=gschorcht
### Contribution description
This PR adds the USB OTG support for STM32U5 and the `b_u585i_iot02a` board.
This PR includes PR #19795 since it uses directly the changes made in PR #19795.
### Testing procedure
Compile and flash
```
BOARD=b-u585i-iot02a make -C tests/sys/usbus_cdc_ecm/ flash term
```
Use the `sudo dmesg` command to get the kernel messages.
```pyhon
[766948.556645] usb 1-2.2: new full-speed USB device number 108 using xhci_hcd
[766948.658688] usb 1-2.2: New USB device found, idVendor=1209, idProduct=7d00, bcdDevice= 1.00
[766948.658696] usb 1-2.2: New USB device strings: Mfr=3, Product=2, SerialNumber=4
[766948.658699] usb 1-2.2: Product: b-u585i-iot02a
[766948.658702] usb 1-2.2: Manufacturer: RIOT-os.org
[766948.658704] usb 1-2.2: SerialNumber: AA140057DA41D467
[766948.668681] cdc_ether 1-2.2:1.0 usb0: register 'cdc_ether' at usb-0000:00:14.0-2.2, CDC Ethernet Device, ea:dc:44:71:d9:24
[766948.743250] cdc_ether 1-2.2:1.0 enxeadc4471d924: renamed from usb0
```
Use the `ifconfig` command on the node to determine the IPv6 LLUA and ping the node.
```
ping6 -c 3 fe80::e8dc:44ff:fe71:c524%enxeadc4471d924
PING fe80::e8dc:44ff:fe71:c524%enxeadc4471d924(fe80::e8dc:44ff:fe71:c524%enxeadc4471d924) 56 data bytes
64 bytes from fe80::e8dc:44ff:fe71:c524%enxeadc4471d924: icmp_seq=1 ttl=64 time=0.523 ms
64 bytes from fe80::e8dc:44ff:fe71:c524%enxeadc4471d924: icmp_seq=2 ttl=64 time=0.546 ms
64 bytes from fe80::e8dc:44ff:fe71:c524%enxeadc4471d924: icmp_seq=3 ttl=64 time=0.599 ms
```
### Issues/PRs references
Includes PR #19795
19802: cpu/nrf53: enable flashpage support r=benpicco a=dylad
### Contribution description
This PR enables flashpage support on nRF53 family.
The peripheral is identical to nRF52, just add the flashpage configuration and enable the module in both Makefiles.features and Kconfig.
### Testing procedure
run `/tests/periph/flashpage` on `nrf5340dk-app`
output of `make BOARD=nrf5340dk-app flash test`
```
/home/dylan/work/RIOT/dist/tools/pyterm/pyterm -p "/dev/ttyACM0" -b "115200" --no-reconnect --noprefix --no-repeat-command-on-empty-line
Twisted not available, please install it if you want to use pyterm's JSON capabilities
Connect to serial port /dev/ttyACM0
Welcome to pyterm!
Type '/exit' to exit.
>
>
test_last_raw
> test_last_raw
wrote raw short buffer to last flash page
> help
help
Command Description
---------------------------------------
info Show information about pages
dump Dump the selected page to STDOUT
dump_local Dump the local page buffer to STDOUT
read Copy the given page to the local page buffer and dump to STDOUT
write Write the local page buffer to the given page
write_raw Write (ASCII, max 64B) data to the given address
erase Erase the given page buffer
edit Write bytes to the local page buffer
test Write and verify test pattern
test_last_pagewise Write and verify test pattern on last page available
test_last_pagewise
test_reserved_pagewise Write and verify short write on reserved page
test_last_raw Write and verify raw short write on last page available
> test_last_pagewise
wrote local page buffer to last flash page
> help
help
Command Description
---------------------------------------
info Show information about pages
dump Dump the selected page to STDOUT
dump_local Dump the local page buffer to STDOUT
read Copy the given page to the local page buffer and dump to STDOUT
write Write the local page buffer to the given page
write_raw Write (ASCII, max 64B) data to the given address
erase Erase the given page buffer
edit Write bytes to the local page buffer
test Write and verify test pattern
test_last_pagewise Write and verify test pattern on last page available
test_reserved_pagewise Write and verify short write on reserved page
test_reserved_pagewise
test_last_raw Write and verify raw short write on last page available
> test_reserved_pagewise
Reserved page num: 5
Since the last firmware update this test has been run 0 times
wrote local page buffer to reserved flash page
When running on a bootloader, as an extra check, try restarting the board and check whether this application still comes up.
> help
help
Command Description
---------------------------------------
info Show information about pages
dump Dump the selected page to STDOUT
dump_local Dump the local page buffer to STDOUT
read Copy the given page to the local page buffer and dump to STDOUT
write Write the local page buffer to the given page
write_raw Write (ASCII, max 64B) data to the given address
erase Erase the given page buffer
edit Write bytes to the local page buffer
test Write and verify test pattern
test_last_pagewise Write and verify test pattern on last page available
test_reserved_pagewise Write and verify short write on reserved page
test_last_raw Write and verify raw short write on last page available
>
make : on quitte le répertoire « /home/dylan/work/RIOT/tests/periph/flashpage »
```
### Issues/PRs references
None.
19803: cpu/nrf5x_common: rework LFCLK source selection r=benpicco a=dylad
### Contribution description
This PR changes the source selection of LFCLK for all nRF families.
This idea is to use the values provided by Nordic vendor files to properly populate the source of the LFCLK. Then setup a per CPU check to ensure the value provided at board level is fine. In the end, the LFCLK source selection is a mere assignment.
The selection of the LFCLK source is still done at board level. I also add a bit of documentation to help users to select another value if needed.
I'll provide in a followup PR, `periph_rtt` support for both nRF9160 and nRF53.
### Testing procedure
CI should be enough I think. Otherwise, one can ran tests/periph/rtt on any nRF51-based board and any nRF52-based board.
You can also change the LFCLK source at board level to ensure the guards are doing their jobs.
### Issues/PRs references
None.
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19733: cpu/msp430: reorganize code r=maribu a=maribu
### Contribution description
RIOT supports two distinct families of the MSP430: The [MSP430 x1xx] MCU family and the [MSP430 F2xx/G2xx] MCU family. For both incompatible MCU families the code was located in the msp430fxyz folder, resulting in case of the UART driver in particularly bizarre code looking roughly like this:
```C
#ifndef UART_USE_USCI
/* implementation of x1xx peripheral ... */
#else
/* implementation of F2xx/G2xx peripheral ... */
#endif
/* zero shared code between both variants */
```
This moves peripheral drivers shared between the two families to msp430_common and splits the SPI and UART driver into two MCU families.
In addition, it cleans up the `msp430_regs.h` by dropping most of it and using the macros and symbols provided by the vendor header files. There is little reason for us to maintain constants when TI is already doing that.
[MSP430 x1xx]: https://www.ti.com/lit/ug/slau049f/slau049f.pdf
[MSP430 F2xx/G2xx]: https://www.ti.com/lit/ug/slau144k/slau144k.pdf
19747: gnrc/ipv6/nib: reset rs_sent counter also for not-6LN interfaces r=maribu a=fabian18
19769: cpu/nrf53: add initial support with nRF5340DK-APP board r=maribu a=dylad
### Contribution description
This PR adds support for nRF5340 MCU and its associated Nordic development board, nRF5340DK.
This MCU provides a dual Cortex-M33, one application core running at up to 128MHz, and one network core running at up to 64MHz.
Peripherals are inherited from others Nordic MCUs families so it shouldn't be hard to add more of them in followup PRs.
For now, only the minimal set of peripherals is supported:
- GPIO / GPIO_IRQ
- UART
- TIMER
### Testing procedure
Build the usual test application for the supported peripherals and flash the board.
nRF5340DK provides two serial ports on its embedded debugger. RIOT's shell should be available on the first one (/dev/ttyACM0)
### Issues/PRs references
#18576#19267
19782: cpu/msp430: fix for ti's msp430-gcc-opensource package ld version r=maribu a=hugueslarrive
### Contribution description
My msp430 toolchain (https://www.ti.com/tool/MSP430-GCC-OPENSOURCE) was broken by #19484:
```
hugues@p700:~/github/cpu_msp430_common/RIOT$ BOARD=msb-430 make -j64 -C examples/hello-world
make : on entre dans le répertoire « /home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world »
Building application "hello-world" for "msb-430" with MCU "msp430fxyz".
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/boards/common/init
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/boards/msb-430
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/core
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/core/lib
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430fxyz
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/drivers
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/boards/common/msb-430
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/drivers/periph_common
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/auto_init
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/div
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/libc
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/malloc_thread_safe
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430_common
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/newlib_syscalls_default
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430fxyz/periph
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/preprocessor
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/stdio_uart
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430_common/periph
/opt/ti/msp430-gcc/bin/../lib/gcc/msp430-elf/9.3.1/../../../../msp430-elf/bin/ld: .rodata not found for insert
collect2: error: ld returned 1 exit status
make: *** [/home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world/../../Makefile.include:761 : /home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world/bin/msb-430/hello-world.elf] Erreur 1
make : on quitte le répertoire « /home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world »
hugues@p700:~/github/cpu_msp430_common/RIOT$ /opt/ti/msp430-gcc/msp430-elf/bin/ld --version
GNU ld (Mitto Systems Limited - msp430-gcc 9.3.1.11) 2.34
Copyright (C) 2020 Free Software Foundation, Inc.
This program is free software; you may redistribute it under the terms of
the GNU General Public License version 3 or (at your option) a later version.
This program has absolutely no warranty.
hugues@p700:~/github/cpu_msp430_common/RIOT$ /opt/ti/msp430-gcc/msp430-elf/bin/ld --version | grep -Eo '[0-9]\.[0-9]+'
9.3
1.11
2.34
hugues@p700:~/github/cpu_msp430_common/RIOT$ /opt/ti/msp430-gcc/msp430-elf/bin/ld --version | grep -Eo '[0-9]\.[0-9]+$'
2.34
```
### Testing procedure
```
hugues@p700:~/github/cpu_msp430_common/RIOT$ BOARD=msb-430 make -j64 -C examples/hello-world
make : on entre dans le répertoire « /home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world »
Building application "hello-world" for "msb-430" with MCU "msp430fxyz".
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/boards/common/init
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/boards/msb-430
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/core
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/core/lib
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430fxyz
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/drivers
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/boards/common/msb-430
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/drivers/periph_common
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/auto_init
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/div
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/libc
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/malloc_thread_safe
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/newlib_syscalls_default
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/preprocessor
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430_common
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/stdio_uart
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430fxyz/periph
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430_common/periph
text data bss dec hex filename
8612 722 866 10200 27d8 /home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world/bin/msb-430/hello-world.elf
make : on quitte le répertoire « /home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world »
```
### Issues/PRs references
Introduced by #19484, highlighted in #16727.
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@posteo.net>
Co-authored-by: Fabian Hüßler <fabian.huessler@ml-pa.com>
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Co-authored-by: Hugues Larrive <hlarrive@pm.me>
The MSP430 vendor files already provide macros containing register
constants and symbols (provided via linker scripts) containing addresses
of peripheral registers. So lets make use of that rather than
maintaining a long list of constants.
