There are two schemes for accessing the packet buffer area (PMA) from the CPU:
- 2 x 16 bit/word access scheme where two 16-bit half-words per word can be accessed. With this scheme the access can be half-word aligned and the PMA address offset corresponds therefore to the local USB IP address. The size of the PMA SRAM is usually 1024 byte.
- 1 x 16 bit/word access scheme where one 16-bit half word per word can be accessed. With this scheme the access can only be word-aligned and the PMA address offset to a half-word is therefore twice the local USB IP address. The size of the PMA SRAM is usually 512 byte.
Which access scheme is used depends on the STM32 model.
The addressing of the Packet buffer Memory Area (PMA) is done locally in the USB IP core in half-words with 16-bit. The `_ep_in_buf` and `_ep_out_buf` arrays which hold these USB IP local addresses in the PMA for initialized EPs therefore always use `uint16_t`.
If the MCU does not have an internal D+ pullup and there is no dedicated GPIO to simulate a USB disconnect, the D+ GPIO is temporarily configured as an output and pushed down to simulate a disconnect/connect cycle to allow the host to recognize the device. However, this requires an external pullup on D+ signal to work
If `RCC_CFGR_USBPRE` is defined, the USB device FS clock of 48 MHz is derived from the PLL clock. In this case the PLL clock must be configured and must be either 48 MHz or 72 MHz. If the PLL clock is 72 MHz it is pre-divided by 1.5, the PLL clock of 48 MHz is used directly.
When using DMA to transfer endpoint data from the RX FIFO to the
endpoint memory, the RXFLVL irq is not needed as that is already handled
by the DMA. Furthermore, servicing this irq anyway can cause the event
handling to interpret data from the FIFO as the endpoint and status
marker during the DMA transfer.
This commit masks the RXFLVL irq while DMA is used for the endpoint
transfers.
Since SLAAC now happens on the up event, the tests needs to ensure, that
`gnrc_ipv6_nib_iface_up()` is called before assuming SLAAC happened. For
the mock interface, this is done by gnrc_ipv6_nib_iface_up().
The definition in `pkg/esp32_sdk/Makefile.include` was evaluated by
`make` after the include paths were already set, resulting in
`ESP32_SDK_DIR` being empty in
INCLUDES += -I$(ESP32_SDK_DIR)/components
[...]
This in turn resulted in
cc1: error: /components: No such file or directory [-Werror=missing-include-dirs]
[...]
The parameters for parity and stop bits was confused, resulting in
the following compilation error with GCC 12.2.0:
/home/maribu/Repos/software/RIOT/cpu/esp_common/periph/uart.c: In function '_uart_config':
/home/maribu/Repos/software/RIOT/cpu/esp_common/periph/uart.c:394:61: error: implicit conversion from 'uart_stop_bits_t' to 'uart_parity_t' -Werror=enum-conversion]
394 | if (_uart_set_mode(uart, _uarts[uart].data, _uarts[uart].stop,
| ~~~~~~~~~~~~^~~~~
/home/maribu/Repos/software/RIOT/cpu/esp_common/periph/uart.c:395:42: error: implicit conversion from 'uart_parity_t' to 'uart_stop_bits_t' -Werror=enum-conversion]
395 | _uarts[uart].parity) != UART_OK) {
| ~~~~~~~~~~~~^~~~~~~
cc1: all warnings being treated as errors
This swaps the parameters.
The cpus for the sam*xpro series have some differences in make and Kconfig
Kconfig seems to be more verbose and make assumes samr34-xpro just uses saml21
The argument regif was removed from the shell command in https://github.com/RIOT-OS/RIOT/pull/18053,
so there is not much need to keep it in the ShellInteraction for that command.
