Using the TER bit in the TX descriptors when only using a single descriptor for
sending triggered a hardware bug. Thus, stop using the TER bit and store the
currently active TX descriptor in RAM instead.
The stm32_eth driver was build on top of the internal API periph_eth, which
was unused anywhere. (Additionally, with two obscure exceptions, no functions
where declared in headers, making them pretty hard to use anyway.)
The separation of the driver into two layers incurs overhead, but does not
result in cleaner structure or reuse of code. Thus, this artificial separation
was dropped.
The Ethernet DMA is capable of collecting a frame from multiple chunks, just
like the send function of the netdev interface passes. The send function was
rewritten to just set up the Ethernet DMA up to collect the outgoing frame
while sending. As a result, the send function blocks until the frame is
sent to keep control over the buffers.
This frees 6 KiB of RAM previously used for TX buffers.
1. Move buffer configuration from boards to cpu/stm32
2. Allow overwriting buffer configuration
- If the default configuration ever needs touching, this will be due to a
use case and should be done by the application rather than the board
3. Reduce default RX buffer size
- Now that handling of frames split up into multiple DMA descriptors works,
we can make use of this
Note: With the significantly smaller RX buffers the driver will now perform
much worse when receiving data at maximum throughput. But as long as frames
are small (which is to be expected for IoT or boarder gateway scenarios) the
performance should not be affected.
If any incoming frame is bigger than a single DMA buffer, the Ethernet DMA will
split the content and use multiple DMA buffers instead. But only the DMA
descriptor of the last Ethernet frame segment will contain the frame length.
Previously, the frame length calculation, reassembly of the frame, and the
freeing of DMA descriptors was completely broken and only worked in case the
received frame was small enough to fit into one DMA buffer. This is now fixed,
so that smaller DMA buffers can safely be used now.
Additionally the interface was simplified: Previously two receive flavors were
implemented, with only one ever being used. None of those function was
public due to missing declarations in headers. The unused interface was
dropped and the remaining was streamlined to better fit the use case.
Seems like the Interrupt flag for a Capture/Compare channel gets set when
- the CC-value is reached
- the timer resets before the CC value is reached.
We only want the first event and ignore the second one. Unfortunately I did
not find a way to disable the second event type, so it is filtered in software.
That is we need to
- ignore the CC-interrupts when the COUNT register register is reset
- ignore the CC-interrupts > TOP value/ARR (auto-reload register)
- Added missing wait for TX flush
- Grouped access to the same registers of the Ethernet PHY to reduce accesses.
(The compiler won't optimize accesses to `volatile`, as defined in the C
standard.)
- Add missing `volatile` to DMA descriptor, as memory is also accessed by the
DMA without knowledge of the compiler
- Dropped `__attribute__((packed))` from DMA descriptor
- The DMA descriptor fields need to be aligned on word boundries to
properly function
- The compiler can now more efficiently access the fields (safes ~300 B ROM)
- Moved the DMA descriptor struct and the flags to `periph_cpu.h`
- This allows Doxygen documentation being build for it
- Those types and fields are needed for a future PTP implementation
- Renamed DMA descriptor flags
- They now reflect to which field in the DMA descriptor they refer to, so
that confusion is avoided
- Added documentation to the DMA descriptor and the corresponding flags
- Make use of the fact that gpio_init_af() does not need prior call to
gpio_init() for all STM32 families anymore and drop call to gpio_init()
- Initialize the UART periph first, before initializing the pins
- While uninitialized, the UART periph will send signal LOW to TXD. This
results in a start bit being picked up by the other side.
- Instead, we do not connect the UART periph to the pins until it is
initialized, so that the TXD level will already be HIGH when the pins
are attached.
- This results in no more garbage being send during initialization
- Do not set an intermediate mode, prepare correct mode settings in a temporary
variable
- Consistently enabled the GPIO periph in gpio_init_af()
- Previously, STM32 F1 did not require a separate call to gpio_init() prior
to a call of gpio_init_af(), but other STM32 families did
- Now, gpio_init_af() can be used without gpio_init() consistently
- STM32 F1: Do not touch ODR for non input pins
- For input pins, this enables / disabled pull up resistors. For outputs,
this register should remain untouched (according to API doc)
cpu/stm32/qdec: test if callback pointer is set
Callback pointer is not tested and could result in a hard fault
if the pointer is NULL.
Thus only activate interrupt if a callback provided.
Signed-off-by: Gilles DOFFE <g.doffe@gmail.com>
If a write to a full tsrb is attempted with disabled interrupts
or in a interrupt then a deadlock will occure. To avoid this make
space in the ringbuffer by synchrnously writing to uart.
The DMA stream will automatically disable itself as soon as the transfer
is finished. No need to do this an additional time after the transfer is
finished
This combines a number of register writes in the SPI
acquire and transfer code. The DMA enable for SPI is moved to the
acquire function, switching between DMA and regular transfer between
acquires is not possible.
This commit adds two new functions to the DMA peripheral code for the
stm32. The setup function allows for a one-time setup of peripheral
config. The prepare function does the per-transfer setup. This allows
for a single setup call during the peripheral lock step and a
per-transfer call to the prepare function.
This commit removes a number of assert statements that should already
have been hit before. This is the reason that the assert in the
acquire function is left.
The FCR register content might change during mem-to-mem DMA transfers,
Forcing it back in the acquire should be sufficient to ensure proper
operations.
