Gunar Schorcht
3d93b2bcf0
drivers/periph/i2c: i2c_acquire() returns void
...
Since all implementations simply return 0 and most drivers do not check the return value, it is better to return void and use an assert to ensure that the given device identifier and given device parameters are correct.
2021-11-29 06:35:25 +01:00
Leandro Lanzieri
d962787043
Merge pull request #17274 from fjmolinas/pr_kconfig_nrf51
...
cpu/nrf51: model kconfig
2021-11-26 12:55:27 +01:00
Leandro Lanzieri
e44ff31560
drivers/sx127x/kconfig: rework modelling
2021-11-26 11:06:50 +01:00
Francisco Molina
3a4f30ec80
drivers/periph_common: add periph_uart_hw_fc
2021-11-26 10:39:40 +01:00
Francisco Molina
272ebd73f4
drivers/bmx055: add saul_default Kconfig selection
2021-11-26 10:39:40 +01:00
Francisco Molina
dbdaa776e4
drivers/mma8x5x: add HAVE_MMA8X5X
2021-11-25 12:33:40 +01:00
f47db6f2c2
drivers/dsp0401: migrate to ztimer
2021-11-23 15:58:56 +01:00
Leandro Lanzieri
7036388769
drivers/periph_common: add RTC ms module to Kconfig
2021-11-22 12:25:57 +01:00
Leandro Lanzieri
e525e23143
drivers/dfplayer: add no_strerror option to Kconfig
2021-11-22 12:25:57 +01:00
Leandro Lanzieri
0a19e58fcb
driver/at30tse75x/Kconfig: enable as default sensor when present
2021-11-22 12:25:31 +01:00
Leandro Lanzieri
e6789198f8
drivers/at24mac/Kconfig: enable as EUI provider when present
2021-11-22 12:25:31 +01:00
Leandro Lanzieri
7c5630032f
drivers/bmx280: refactor Kconfig model
2021-11-22 12:25:31 +01:00
Leandro Lanzieri
347fb256d5
drivers/at24mac: add Kconfig feature
2021-11-22 12:25:31 +01:00
Wouter Symons
5055d0993e
drivers/dht: correct interpreting raw values
2021-11-20 14:55:02 +01:00
Benjamin Valentin
669104d841
cpu/sam0_common: SPI: don't perform DMA transfer for small buffers
...
Setting up a DMA transfer can take longer than sending out a buffer
byte by byte if the buffer is small.
DMA only shows advantages for large buffers, using it for every transfer
will cause a net slowdown.
Since we did not come up with a good way to determine the treshold based
on the SPI frequency, just use a fixed buffer for now so that DMA can be
used without slowing things down overall.
2021-11-19 17:22:51 +01:00
benpicco
24aa7eb6bf
Merge pull request #17191 from benpicco/drivers/periph-byte_type
...
drivers/periph: use uint_fast8_t as default type
2021-11-18 17:21:55 +01:00
Leandro Lanzieri
c5f9d50a57
socket_zep: add Kconfig
2021-11-18 14:17:29 +01:00
Benjamin Valentin
1768e93710
drivers/periph: use uint_fast8_t as default type
...
The default driver type is just an index into a device array defined
by the board.
If a platform wants to encode additional information in the device type,
it can define a custom type.
This means we can just set the default type to whatever fits the target
CPU best.
On ARM this will still be a 32 bit word, but on AVR it will by a 8 bit byte.
2021-11-18 10:29:50 +01:00
Benjamin Valentin
4664e63ad4
drivers/soft_uart: fix type usage
2021-11-18 10:14:51 +01:00
Leandro Lanzieri
6a1340da26
drivers/si70xx/kconfig: rework
2021-11-18 09:03:07 +01:00
Leandro Lanzieri
a8d679062a
drivers/ccs811/kconfig: add feature symbol
2021-11-18 09:03:07 +01:00
Leandro Lanzieri
ab84ec5134
drivers/bmx280: rework Kconfig model
2021-11-18 09:03:07 +01:00
f8e7e2f557
usbdev_mock: Adapt to xmit API
...
Includes the adaptations needed in the test application
2021-11-16 20:16:59 +01:00
597f1d19aa
usbdev: Refactor to xmit API
...
This API change refactors the usbdev API to supply buffers via the
usbdev_ep_xmit function. This changes from the usbdev_ep_ready call to allow
separate buffers per call. An usbdev_ep_buf_t pseudotype is available and must
be used when defining buffers used for endpoints to adhere to the DMA alignment
restrictions often required with usb peripherals.
Main advantage is that the usbdev peripherals no longer have to allocate
oversized buffers for the endpoint data, potentially saving multiple KiB
of unused buffer space. These allocations are now the responsibility of
the individual USB interfaces in the firmware
2021-11-16 11:21:07 +01:00
59e85cf921
usbdev: Refactor to xmit API
...
This API change refactors the usbdev API to supply buffers via the
usbdev_ep_xmit function. This changes from the usbdev_ep_ready call to allow
separate buffers per call. An usbdev_ep_buf_t pseudotype is available and must
be used when defining buffers used for endpoints to adhere to the DMA alignment
restrictions often required with usb peripherals.
Main advantage is that the usbdev peripherals no longer have to allocate
oversized buffers for the endpoint data, potentially saving multiple KiB
of unused buffer space. These allocations are now the responsibility of
the individual USB interfaces in the firmware
2021-11-16 11:21:00 +01:00
Francisco
6dbf1c3013
Merge pull request #17102 from aabadie/pr/drivers/ads101x_ztimer
...
drivers/ads101x: migrate to ztimer
2021-11-15 09:56:14 +01:00
benpicco
7da50b05a9
Merge pull request #17190 from benpicco/drivers/dose-padding
...
drivers/dose: reduce struct padding
2021-11-12 20:45:24 +01:00
Karl Fessel
3d33cee551
Merge pull request #17137 from kfessel/p-ztimer-at30tse75x
...
driver/at30tse75x: port to ztimer_usec
2021-11-12 17:12:11 +01:00
Benjamin Valentin
b34b67feee
drivers/dose: reduce struct padding
...
By moving all the single byte struct elements to the end, we can reduce
padding inside `dose_t` and ensure that `recv_buf` is always aligned.
This saves some RAM:
master
------
text data bss dec hex filename
36384 136 12944 49464 c138 tests/driver_dose/bin/samr21-xpro/tests_driver_dose.e
this patch
----------
text data bss dec hex filename
36484 136 12936 49556 c194 tests/driver_dose/bin/samr21-xpro/tests_driver_dose.elf
2021-11-12 16:19:20 +01:00
Benjamin Valentin
965fa3ef10
drivers/dose: clarify timeout calculation
2021-11-11 14:43:07 +01:00
Benjamin Valentin
32c29bf062
drivers/dose: fix standby mode
...
Previously we would not disable the sense pin, this meant that
a node could still wake up if the standby pin is not connected.
Properly disable sensing when in standby and wait for a state
transition to IDLE to avoid aborting a reception and messing up the
DOSE internal state.
2021-11-11 14:33:55 +01:00
Francisco
b609646961
Merge pull request #17138 from fjmolinas/pr_sx126x_fixes
...
drivers/sx126x: fix sync word and TX PA configuration
2021-11-11 10:59:08 +01:00
benpicco
026d6cfba1
Merge pull request #16768 from benpicco/drivers/dose-timeout_bytes
...
drivers/dose: calculate timeout based on symbol rate
2021-11-10 12:40:13 +01:00
Francisco
035ee0a595
Merge pull request #17172 from kaspar030/drivers_ds18_missing_stdint.h
...
drivers/ds18.h: add missing stdint.h include
2021-11-10 08:42:03 +01:00
Francisco
fb4947937f
Merge pull request #17169 from gschorcht/doc/fix_ccs811_doc
...
drivers/ccs811: fix of documentation
2021-11-10 08:41:26 +01:00
5d3a4d63d8
drivers/ds18.h: add missing stdint.h include
2021-11-09 21:48:48 +01:00
Gunar Schorcht
8e88906445
drivers/ccs811: fix of documentation
2021-11-09 19:50:07 +01:00
benpicco
12ade5a8b5
Merge pull request #16752 from benpicco/drivers/dose-standby
...
drivers/dose: enable standby pin
2021-11-09 18:20:17 +01:00
Benjamin Valentin
6c1481b6ee
drivers/dose: enable standby pin
...
Some CAN transceivers have a standby pin that has to be pulled low
in order to use it.
If the interface is disabled we can set it to high again to save some
power.
2021-11-09 15:19:35 +01:00
Francisco Molina
e17e3254e1
drivers/sx126x: add tx_pa_mode
...
BOARDs with RF switch might only support one of the TX modes, and
on init the BOARD needs to be configured accordingly and the correct
mode selected on TX.
2021-11-08 18:42:05 +01:00
benpicco
358abcf133
Merge pull request #17156 from maribu/drivers/encx24j600
...
drivers/encx24j600: fix unaligned memory access
2021-11-07 18:55:58 +01:00
Marian Buschsieweke
4c22716001
drivers/encx24j600: make cppcheck happy
...
Rename cmd buffer to cmd_buf to avoid shadowing outer function.
2021-11-07 08:46:06 +01:00
Marian Buschsieweke
9f1cece6ee
drivers/encx24j600: fix unaligned memory access
2021-11-06 20:33:43 +01:00
Marian Buschsieweke
5e75047a2b
drivers/lis3dh: fix unaligned memory access
...
The bogus packed attribute added to lis3dh_data_t resulted in the
structure being aligned two 1 byte. It was later casted to an
uint16_t pointer (which is aligned two 2 bytes). By dropping the
packed attribute the alignment mismatch is fixed.
2021-11-06 20:05:05 +01:00
26346188b9
Merge pull request #17105 from aabadie/pr/drivers/ata8520e_ztimer
...
drivers/ata8520e: migrate to ztimer
2021-11-05 16:22:59 +01:00
baa1ed38cc
drivers/ata8520e: migrate to ztimer
2021-11-05 12:49:37 +01:00
benpicco
bfb8d1d3fd
Merge pull request #17014 from benpicco/periph/gpio-cb_not_NULL
...
drivers/periph/gpio: state that interrupt callback must not be NULL
2021-11-05 12:47:16 +01:00
Karl Fessel
314bc00902
driver/at30tse75x: cleanup for static tests
2021-11-05 12:19:35 +01:00
Karl Fessel
fc8e6f01bd
driver/at30tse75x: port to ztimer_usec
2021-11-05 12:19:35 +01:00
eaa007d412
Merge pull request #17135 from bergzand/pr/usbdev/fix_cppcheck_vera
...
usb(dev|bus): Fix static-check issues
2021-11-05 08:36:53 +01:00
7ce5d8a5dd
Merge pull request #17112 from aabadie/pr/drivers/rn2xx3_ztimer
...
drivers/rn2xx3: migrate to ztimer
2021-11-05 00:38:55 +01:00
Francisco
f08c5da7aa
Merge pull request #17101 from aabadie/pr/drivers/bmp180_ztimer
...
drivers/bmp180: migrate to ztimer
2021-11-04 15:25:48 +01:00
Karl Fessel
4d552e7e4a
driver/at30tse75x: avoid direct use of xtimer_ticks
2021-11-04 14:16:07 +01:00
c918630e5e
usbdev_mock: Uncrustified and fixed static-check issues
2021-11-04 13:49:34 +01:00
295092bc29
drivers/rn2xx3: migrate to ztimer
2021-11-04 10:39:36 +01:00
Francisco Molina
5579fd2220
drivers/xbee: uncrustify
2021-11-02 21:46:19 +01:00
Francisco Molina
472f6495a8
drivers/xbee: migrate to ztimer_msec
2021-11-02 21:46:19 +01:00
9029e1caf9
drivers/bmp180: migrate to ztimer
2021-11-02 14:57:50 +01:00
3fa2154d48
drivers/ads101x: migrate to ztimer
2021-11-02 14:49:45 +01:00
Leandro Lanzieri
f64b166319
Merge pull request #16845 from MrKevinWeiss/pr/kconfig/supportstms
...
.murdock: Add nucleo boards to kconfig test
2021-11-01 09:55:22 +01:00
Francisco Molina
9a2c880a60
drivers/stmpe811: use errno
2021-10-30 23:25:50 +02:00
dbbdc8590e
Merge pull request #17031 from fjmolinas/pr_lvgl_ztimer
...
pkg/lvgl: use ztimer instead of xtimer
2021-10-28 11:36:04 +02:00
Ollrogge
c6e94aa6be
periph/flashpage.h: add comment about riotboot impact on flashpage layout
2021-10-26 14:35:33 +02:00
Francisco
7f3344870d
Merge pull request #16972 from Ollrogge/flashpage_pr
...
periph/flashpage: extend API
2021-10-26 12:51:05 +02:00
Francisco Molina
bac1f8c82d
drivers/ili9341: use ztimer instead of xtimer
2021-10-25 10:48:49 +02:00
9f8aee4e95
usbdev: Deprecate USBDEV_EVENT_TR_FAIL
2021-10-24 19:33:29 +02:00
Ollrogge
72d47013dd
periph/flashpage: extend API
2021-10-19 22:33:09 +02:00
Benjamin Valentin
f624eb473a
drivers/periph/gpio: state that interrupt callback must not be NULL
...
This allows us to use `assert(cb != NULL)` inside `gpio_init_int()`
and save a few cycles of interrupt latency.
2021-10-19 21:26:50 +02:00
MrKevinWeiss
9b6a63a951
drivers/kconfig: simplify shared rtt/rtc hardware in kconfig
2021-10-14 11:28:46 +02:00
MrKevinWeiss
c7820cf7e5
*/rtt|rtc: Fix Kconfig modeling
2021-10-14 11:28:44 +02:00
MrKevinWeiss
0c5c657912
drivers/spi: Model Kconfig spi_gpio_mode
2021-10-14 11:28:43 +02:00
Gunar Schorcht
62dd51d8ba
drivers: add anchor to doc to allow stable references
2021-10-13 17:37:16 +02:00
Jose Alamos
cb6e242b65
net/netdev_ieee802154_submac: prevent calling ACK TO fired if cancelled
2021-10-07 14:37:05 +02:00
benpicco
b4de70e9d8
Merge pull request #16922 from jia200x/pr/netdev/signal_netdev_register
...
netdev: add netdev_register_signal
2021-10-05 22:59:49 +02:00
Jose Alamos
503f5a9ddb
netdev: add netdev_register_signal
2021-10-05 14:35:07 +02:00
2ccdac1b7f
drivers/ws281x: declare pseudomodules at driver level
2021-10-05 11:48:53 +02:00
22d9040211
drivers/at: declare pseudomodules at driver level
2021-10-05 11:48:53 +02:00
a090f492bb
drivers/at24cxxx: declare pseudomodules at driver level
2021-10-05 11:48:53 +02:00
a614e9a36e
drivers/ds18: declare pseudomodules at driver level
2021-10-05 11:48:53 +02:00
01de18a855
drivers/qmc5883l: declare pseudomodules at driver level
2021-10-05 11:48:53 +02:00
81d5b7eefb
drivers/at86rf215: declare pseudomodules at driver level
2021-10-05 11:48:52 +02:00
2b3a9b66ea
drivers/bq2429x: declare pseudomodules at driver level
2021-10-05 11:48:52 +02:00
6d57d6ab34
drivers/ina3221: declare pseudomodules at driver level
2021-10-05 11:48:52 +02:00
df2ad2cdde
drivers/lis2dh12: declare pseudomodules at driver level
2021-10-05 11:48:52 +02:00
dc4f9d4c7b
drivers/lpsxxx: declare pseudomodules at driver level
2021-10-05 11:48:52 +02:00
2d2e4d10ae
drivers/vcnl40x0: declare pseudomodules at driver level
2021-10-05 11:48:52 +02:00
fb193ea5cb
drivers/rn2xx3: declare pseudomodules at driver level
2021-10-05 11:48:52 +02:00
982ea7fb6f
drivers/tmp00x: declare pseudomodules at driver level
2021-10-05 11:48:52 +02:00
0a2076a89b
drivers/si70xx: declare pseudomodules at driver level
2021-10-05 11:48:52 +02:00
d2ec49f032
drivers/si114x: declare pseudomodules at driver level
2021-10-05 11:48:51 +02:00
2f7227bd73
drivers/sht1x: declare pseudomodules at driver level
2021-10-05 11:48:51 +02:00
fc5338641e
drivers/sx127x: declare pseudomodules at driver level
2021-10-05 11:48:51 +02:00
a120c2b296
drivers/sx126x: declare pseudomodules at driver level
2021-10-05 11:48:51 +02:00
8a3c103127
drivers/sdp3x: declare pseudomodules at driver level
2021-10-05 11:48:51 +02:00
79a2ea4713
drivers/pn532: declare pseudomodules at driver level
2021-10-05 11:48:51 +02:00
003c472339
drivers/mrf24j40: declare pseudomodules at driver level
2021-10-05 11:48:51 +02:00
60f1615aa3
drivers/lm75: declare pseudomodules at driver level
2021-10-05 11:48:51 +02:00
82e6df6a50
drivers/ina2xx: declare pseudomodules at driver level
2021-10-05 11:48:51 +02:00
a6e58f744c
drivers/mpu9x50: declare pseudomodules at driver level
2021-10-05 11:48:51 +02:00
37a4eed0c4
drivers/mhz19: declare pseudomodules at driver level
2021-10-05 11:48:50 +02:00
