17810: drivers/slipdev: implement sleep states r=benpicco a=benpicco
18348: sys/net/gnrc/pktbuf_static: make use of alignas() r=maribu a=maribu
### Contribution description
Since we are now using C11, we can make use of `alignas()` provided by `<stdalign.h>` to make the alignment code easier to read.
### Testing procedure
I didn't expect this to change binaries, but is safes 4 bytes. `elf_diff` shows that the compiler (at least GCC 11.3.0) was not able to detect that `gnrc_pktbuf_static_buf` was just an alias for `_pktbuf_buf`. That makes sense since it would be hard without LTO to rule out external writes to `gnrc_pktbuf_static_buf`, unless one would have added a `const` (to the pointer, not to the data the pointer points to).
The [output of `elf_diff`](https://mari-bu.de/pr_18348_gnrc_pktbuf_static_elf_diff.html) looks otherwise quite unscary.
Also:
```
$ make BOARD=nucleo-f767zi -C tests/unittests/ tests-pktbuf flash test
make: Entering directory '/home/maribu/Repos/software/RIOT/tests/unittests'
Building application "tests_unittests" for "nucleo-f767zi" with MCU "stm32".
[...]
Welcome to pyterm!
Type '/exit' to exit.
READY
s
START
.............................................
OK (45 tests)
make: Leaving directory '/home/maribu/Repos/software/RIOT/tests/unittests'
```
### Issues/PRs references
None
19120: CI: seperate check-labels and check-commits workflows r=maribu a=kaspar030
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Co-authored-by: Kaspar Schleiser <kaspar@schleiser.de>
19048: drivers/sht2x: some small improvements r=benpicco a=gschorcht
### Contribution description
This PR provides the following improvements for the SHT2x driver:
- migration to `ztimer` 8a605517f5 and 367549940de3bd8910052334c34af028d4992741
- floating point arithmetics replaced by integer arithmetics f424caebbfec9f2be56aa2337c6cc09dba5b97d6
- fix of sleep times (typical times replaced by maximum times as recommended by the datasheet) 13615c72094b8541ee62c3e8ed5a36dc4d725fd0
- release of the I2C bus during sleep 9415c216cfab734520ef98dd00b350c22f342c60
- Kconfig configuration of sensor parameters added dadbbcb4c328350893db53ba6743d03cb34ecc1c
- no-hold mode is now the default mode instead of the hold mode
Regarding the sleep times: The typical measurement times were used as sleep times. According to the datasheet, typical measurements are only recommended for calculating energy consumption, while maximum values should be used for calculating waiting times in communication. Therefore, the typical time values were replaced by maximum time values for the sleep in no-hold mode.
Regarding the hold mode: In hold mode, the sensor uses clock stretching until the measurement results can be read by the MCU. This blocks both the I2C bus and the MCU during the entire measurement, which can take up to 85 ms if I2C is not interrupt-driven. Therefore, the no-hold mode is now used by default, where the calling thread sleeps during the measurement, but the MCU is not completely blocked. Furthermore, the hold mode requires that the MCU supports clock stretching. Even if the MCU supports clock stretching, the hold mode with clock stretching doesn't seem to work with different MCUs. I couldn't get it working for STM32 and ESP32.
Regarding the I2C bus during sleep: If the no-hold mode is used and the calling thread sleeps up to 85 ms, it makes sense to release the I2C bus until the measurement results are available.
### Testing procedure
`tests/driver_sht2x` should still work.
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
According to the data sheet, typical times are recommended for calculating energy consumption, while maximum values should be used for calculating waiting times in communication. Therefore, the typical time values are replaced by maximum time values for sleep.
There are many modem commands for which you get a line of response followed
by an OK. Take for example the AT+CGSN command to get the IMEI of a Ublox
G350.
>> AT+CGSN
<< 004999010640000
<< OK
- most were trivial
- missing group close or open
- extra space
- no doxygen comment
- name commad might open an implicit group
this hould also be implicit cosed but does not happen somtimes
- crazy: internal declared groups have to be closed internal
- replace all `int`s and `unsigned`s with integers with fixed width
- replaced all signed integers of sizes with unsigned ones (sizes
cannot be negative)
- made bitshifts 8-bit safe (e.g. `1 << 24` is valid on 32-bit, but
undefined behavior on 8-bit, as a 16 bit wide `int` would be shifted
by more than the type width)
- use `void *` / `const void *` for data buffers to ease use
This makes life easier when calling e.g. `saul_reg_write()` with data
stored in flash.
As now the signatures for reading and writing differ (in that `const`
qualifier only), `saul_notsup()` is split into `saul_write_notsup()`
and `saul_read_notsup()`. However, one is implemented as a symbol alias
of the other, so that ROM consumption remains unchanged.
