To be able to define common configurations for all ESP CPUs, the CPU specific configuration cpu_conf.h has to include a common configuration. For that purpose cpu_conf.h in cpu/esp_common is renamed to cpu_conf_common.h and included in CPU specific configurations.
During the write access to the SPI flash, the IROM cache is not available and only code from the IRAM can be executed. Therefore, the code of file system implementations which access the SPI flash must reside in IRAM.
The same tool 'gen_esp32part.py' is used for the generation of partition tables on ESP8266 as well as n ESP32. The tool is therefore added to 'dist/tools/esptool'
With the new toolchain version required to fix issue #13133, the compilation of `examples/posix_socket` fails due to a C linkage error in `atomic_base.h`. The reason is that including `drivers/include/mtd.h` in `boards/esp32/board_common.h` inside the `extern C` block finally leads to including `atomic_base.h` inside the `extern C` block which in turn to the C linkage error for the template definitions in this file.
ESP32 can be clocked with either a 40 MHz or 26 MHz crystal. Since most boards use a 40 MHz crystal, the configuration was previously fixed to a 40 MHz crystal. This commit changes the crystal from 40 MHz to automatic detection, allowing boards with a 26 MHz crystal like the Sparkfun ESP32 Thing DEV to be used.
- Unecessary definitions are removed.
- Since the 48-bit RTC hardware timer uses a RC oscillator as clock, it is pretty inaccurate and leads to a RTC time deviation of up to 3 seconds per minute. Therefore, a calibration during the boot time determines a correction factor for the 48-bit RTC hardware timer. Function _rtc_time_to_us uses now this correction factor and converts a raw 48-bit RTC time to a corrected time in microseconds. Thus, the 48-bit RTC timer becomes much more accurate, but it can't still reach the accuracy of the PLL driven 64-bit system timer. The Advantage of using RTC over 64-bit sydtem timer is that it also continues in deep sleep mode and after software reset.
- If the 64-bit system timer is used to emulate the RTC timer, it uses the RTC hardware timer to continue its operation after software .
It is possible to use different timers as RTC timer for the periph_rtc module. Either the 48-bit RTC hardware timer is used directly or the PLL driven 64-bit system timer emulates a RTC timer. The latter one is much more accurate. Pseudomodule esp_rtc_timer controlls which timer is used. Only if esp_rtc_timer is enabled explicitly, the 48-bit RTC hardware timer is used. Otherwise the 64-bit sytstem timer is used to emulate the RTC timer.
The explicit call of rtc_init during the CPU start was removed because rtc_init is called within the function periph_init. The display of the system time at startup had to be placed after the call to periph_init.
There is an existing function that returns the system time in us as a 64 bit value. Converting this 64 value in us to a 32 bit value in ms is more easier and uses the complete 32 bit range. Using only the low part of the 64 bit system time in us and dividing it by 1e3 cuts the 32 bit range.
To control the log level and the format of the log output of SDK libraries, a bunch of library-specific printf functions are realized which map the log output from SDK libraries to RIOT's log macros.
The buffer[EHTHERNET_MAX_LEN] used in _esp_wifi_send to convert the iolist of the given packet to a plain buffer for the WiFi interface should not be on the stack to prevent the sending thread's stack from overflowing.
To avoid that murdock times out before tests/pkg_spiffs and tests/pkg_littlefs time out, the configured test timeouts for these tests is reduced to 200 seconds which should be enough. An ESP32 needs an average of 60 seconds for these tests, while an ESP8266 needs in average 100 seconds.
ESP32 nodes can crash during SPI Flash write operations if required parts of the code are not in the IRAM but in the cached SPI Flash memory, which is disabled during the SPI Flash write operations. Therefore, the code of the SPIFFS package and the VFS module are now stored in the IRAM.
To reduce the information that are printed at the console during the startup, special bootloaders are required that suppress the outputs which are only informational. The according bootloader has to be selected during the make process.
Startup information, including board configuration, is only printed when module esp_log_startup is used. This reduces the amount of information that is printed by default to the console during the startup. The user can enable module esp_log_startup to get the additional startup information.
The UART peripheral clock seems to be sporadically set to wrong value when the CPU clock is changed. In this case, the UART clock is not set to 115.200 kbps but to 96 kbps, so that the output in the console seems like garbage. This can also cause automatic tests to fail. Therefore, the CPU clock is only changed if CONFIG_ESP32_DEFAULT_CPU_FREQ_MHZ defines a different default CPU clock than the one already used at boot time.
If the user or the board definition doesn't enable `esp_wifi` or `esp_eth`, `esp_now` is defined as default netdev.
fixup! cpu/esp32: defines esp_now as default netdev
To be able to catch a core panic in debugger and to get the last output from asynchronous UART , e.g., if the stack is smashed, the system is not rebooted immediately anymore but breaks, which stops the execution in debugger or reboots the system after WDT timeout.
Log outputs generated by binary ESP32 SDK libraries are mapped to the ESP32's log module which supports colored and tagged log outpus. Tagged log outputs from SDK libraries are handled accordingly.
The implementation of `log_module` for ESP32 was changed from functions to a macro-based implementation to be able to use the bunch of macros for colored and tagget log output generation.
