The current implmentation right shifted the 16 bit value passed into
`dac_set()` down to the 12 bits that the DAC is actually capable of.
This patch drops the shift and instead writes the 16 bit value to the
DAC's left aligned 12 bit wide data holding register.
19516: cpu/rpx0xx: add initial ADC support r=dylad a=dylad
### Contribution description
This PR adds initial support for RP2040 ADC peripheral.
It is rather minimalist, and only use oneshot trigger to perform a single acquisition.
I've tested this PR using a potentiometer connected between GND and 3V3.
GP26, GP27, GP28 has been tested.
### Testing procedure
Select `ADC_RES_12BIT` and flash `tests/periph_adc`
`make BOARD=rpi-pico -C tests/periph_adc`
### Issues/PRs references
None.
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
19346: pkg/tinydtls: allow build for AVR r=benpicco a=benpicco
19512: SUBSYSTEMS.md: add jia200x to subsystems r=benpicco a=jia200x
19513: boards/nrf52840dongle/doc: Update nrfutil pointers r=benpicco a=chrysn
### Contribution description
Nordic changed its nrfutil; this change adjust to it.
I'm not fully happy with recommending that tool at all due to its bad quality (see rambling in https://github.com/RIOT-OS/RIOT/issues/19511), but short of soldering on a debug header or touch-probing it with wires it's the only way in to the device. I may later add follow-up recommendations to switch to riotboot, but this now at least fixes the immediate issue.
### Testing procedure
* Look at the updated documentation.
### Issues/PRs references
Closes: https://github.com/RIOT-OS/RIOT/issues/19511
19514: dist/testbed-support: remove obsolete boards from iotlab archi r=benpicco a=aabadie
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Benjamin Valentin <benjamin.valentin@bht-berlin.de>
Co-authored-by: Jose Alamos <jose@alamos.cc>
Co-authored-by: chrysn <chrysn@fsfe.org>
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
19507: cpu/cc26x0_cc13x0: Drop feature cortexm_mpu r=maribu a=maribu
### Contribution description
At least the CC2650 doesn't have an MPU, I assume this is also true for the rest of the family.
The CC2652 does have an MPU according to the datasheet. So I keep the feature there in place.
### Testing procedure
E.g.
```
make BOARD=cc2650-launchpad -C tests/mpu_noexec_ram flash test
```
fails. (Note: A successful test run would also crash but with a mem manage handler rather than a hardfault due to an invalid instruction on the stack being executed.)
It would be nice to also test the same for a `cc2652-launchpad`, for which the MPU should work.
### Issues/PRs references
None
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
At least the CC2650 doesn't have an MPU, I assume this is also true
for the rest of the family.
The CC2652 does have an MPU according to the datasheet. So I keep the
feature there in place.
GCC 12 create a bogus array out of bounds warning as it assumes that
because there is special handling for `uart == 0` and `uart == 1`,
`uart` can indeed be `1`. There is an `assert(uart < UART_NUMOF)` above
that would blow up prior to any out of bounds access.
In any case, optimizing out the special handling of `uart == 1` for
when `UART_NUMOF == 1` likely improves the generated code and fixes
the warning.
/home/maribu/Repos/software/RIOT/cc2650/cpu/cc26xx_cc13xx/periph/uart.c:88:8: error: array subscript 1 is above array bounds of 'uart_isr_ctx_t[1]' [-Werror=array-bounds]
88 | ctx[uart].rx_cb = rx_cb;
| ~~~^~~~~~
/home/maribu/Repos/software/RIOT/cc2650/cpu/cc26xx_cc13xx/periph/uart.c:52:23: note: while referencing 'ctx'
52 | static uart_isr_ctx_t ctx[UART_NUMOF];
| ^~~
/home/maribu/Repos/software/RIOT/cc2650/cpu/cc26xx_cc13xx/periph/uart.c:89:8: error: array subscript 1 is above array bounds of 'uart_isr_ctx_t[1]' [-Werror=array-bounds]
89 | ctx[uart].arg = arg;
| ~~~^~~~~~
/home/maribu/Repos/software/RIOT/cc2650/cpu/cc26xx_cc13xx/periph/uart.c:52:23: note: while referencing 'ctx'
52 | static uart_isr_ctx_t ctx[UART_NUMOF];
| ^~~
To be able to reconfigure the PLL multiplier in clock configuration, the existing value has to be reset first. This becomes necessary when changing the core clock, e.g. when booting with riotboot an application that uses USB.
To allow CPU specific definitions in `cpu.h`, `riscv_common/cpu.h` is renamed to ``riscv_common/cpu_common.h` and included in new `cpu.h` files for FE310 and GD32V.
19450: cpu/esp32: fix compilation issues with GCC 12.2 r=benpicco a=gschorcht
### Contribution description
This PR provides the changes in `cpu/esp32` and `cpu/esp_common` to fix the compilation issues with GCC v12.2. It is required as the first step in the preparation of the upgrade to ESP-IDF version 5.1.
**Please note**: Insead of fixing the ESP-IDF 4.4 code itself by a big bunch of patches to fix the compilation problems with GCC v12.2, it temporarily disables some warnings. The reason is that the ESP-IDF 5.1 requires GCC v12.2 and should be fixed for this compiler version by the vendor.
### Testing procedure
Green CI
The change were already tested with all ESP-specific modules like `esp_now`, `esp_wifi`, `esp_spi` and `esp_ble` for all supported ESP platforms.
### Issues/PRs references
Prerequisite for https://github.com/RIOT-OS/riotdocker/pull/227
Fixes issue #19421
19476: native/syscalls: rename real_clock_gettime to clock_gettime r=benpicco a=Teufelchen1
### Contribution description
When compiling RIOT for native using a recent LLVM and enabling ASAN, one might encounter "Duplicated symbol".
This is due to a name clash with `real_clock_gettime()` in compiler-rt from [LLVM](f50246da65), I renamed RIOTs `real_clock_gettime` and just default to the posix function `clock_gettime`. The wrapper existed, most likely, for consistency only.
(The best solution would probably to convince the LLVM folks to declare their symbol as `static` and refactor a bit)
### Testing procedure
Passing CI should be enough.
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: Teufelchen1 <bennet.blischke@haw-hamburg.de>
Since the USB OTG FIFO sizes are partly defined in 32-bit words and partly in bytes, the documentation of the of the USB OTG FIFO size definitions is extended by the respective unit.
Since the USB OTG FIFO sizes are partly defined in 32-bit words and partly in bytes, the documentation of the of the USB OTG FIFO size definitions is extended by the respective unit.
Since the USB OTG FIFO sizes are partly defined in 32-bit words and partly in bytes, the documentation of the of the USB OTG FIFO size definitions is extended by the respective unit.
19460: cpu/stm32/usbdev_fs: fix ep registration and EP_REG assignments r=gschorcht a=dylad
### Contribution description
This PR provides two fixes for the `usbdev_fs` driver:
- Fix endpoints registration
- Fix assignment of toggleable bits in EP_REG(x) registers
These bugs were encountered with the USBUS MSC implementation.
Regarding the endpoints registration:
For the `usbdev_fs` peripheral, IN and OUT endpoints of the same index must have the same type.
For instance, if EP1 OUT is a bulk endpoint, EP1 IN must either be unused or used as bulk too but it cannot be used as interrupt or isochronous.
With the previous check, the following registration pattern (EP OUT Bulk -> EP IN Interrupt -> EP IN Bulk) would assign both EP OUT Bulk and EP IN Interrupt to same endpoint index. So the configuration would be broken.
Applying the same registration pattern with this patch would now produce EP OUT Bulk -> 1 / EP IN Interrupt -> 2 / EP IN Bulk 1. Which is a working configuration for this IP.
and for the second fix:
EP_REG(x) registers have a total of 6 toggleable bits. Those bits can only be toggled if we write a one to it, otherwise writing a zero has no effect
This commit fixes all the access to these registers to prevent from modifying these bits when not needed.
Without this patch, the endpoint status (VALID / NACK / STALL) can be erroneously modify because bits are not cleared when assigning the new content to the register and thus make the bits toggle and change values.
### Testing procedure
This can be tested with tests/usbus_msc on any board using this `usbdev_fs` driver.
It is easier to test this PR with #19443 alongside. Then the following would be enough:
`CFLAGS='-DSECTOR_COUNT=64' USEMODULE='mtd_emulated' make -j8 BOARD=p-nucleo-wb55 -C tests/usbus_msc flash`
Otherwise this can also be tested by attaching a SPI<->SDCARD adapter.
### Issues/PRs references
None.
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
EP_REG(x) registers have a total of 6 toggleable bits. Those bits can only be toggled if we write a one to it, otherwise writing a zero has no effect
This commit fixes all the access to these registers to prevent from modifying these bits when not needed
Signed-off-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
For the usbdev_fs peripheral, IN and OUT endpoints of the same index must have the same type.
For instance, if EP1 OUT is a bulk endpoint, EP1 IN must either be unused or used as bulk too but it cannot be used as interrupt or isochronous.
With the previous check, the following registration pattern (EP OUT Bulk -> EP IN Interrupt -> EP IN Bulk) would assign both EP OUT Bulk and EP IN Interrupt to same endpoint index. So the configuration would be broken.
Applying the same registration pattern with this patch would now produce EP OUT Bulk -> 1 / EP IN Interrupt -> 2 / EP IN Bulk 1. Which is a working configuration for this IP
Signed-off-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
The comments still claim STM32F1 support is missing, but this was
recently added.
Also, drop an empty line to fix `too many consecutive empty lines`
nitpick of the CI.
The driver previously failed to reliably clear the RXNE bit, resulting
in the next transfer to incorrectly read a stale register value. This
was noticed with the SD card SPI driver on an STM32F4, in which the
0xff byte of the previous byte transfer was returned instead of the
actual status byte, throwing the SD card driver off the rails.
A number of ESP-IDF header files that are needed to compile RIOT include the header file `driver/gpio.h` only because of the definition of the type `gpio_num_t`. However, this header file contains the entire GPIO API definition of the ESP-IDF, which conflicts with that of RIOT.
The solution was to use a wrapper library that does not need to include the `driver/gpio.h` file of the ESP-IDF during compilation of RIOT code.
This commit provides another approach which does not require such a wrapper library. It just provides its own `driver/gpio.h` in RIOT that is included by ESP-IDF header files instead of the original `driver/gpio.h` in ESP-IDF. It defines only the required `gpio_num_t` if RIOT code is compiled but includes the original `driver/gpio.h` of ESP-IDF if ESP-IDF code is compiled. This avoids to create a wrapper library for each module.
19420: cpu/esp32: use ets_printf instead of puts in startup r=maribu a=gschorcht
### Contribution description
This PR provides a workaround that fixes the problem that restarting an application automatically after flashing it in download mode via USB Serial/JTAG doesn't work and requires a hard reset by pressing the RESET button before it starts.
The reason that the application doesn't restart automatically after flashing it is that an exception occurs if `puts` or `printf` is called during startup before the first interrupt driven context switch in `thread_yield_higher`. The console seems to hange after bootloader:
```
EESP-ROM:esp32c3-api1-20210207
Build:Feb 7 2021
rst:0x15 (USB_UART_CHIP_RESET),boot:0xd (SPI_FAST_FLASH_BOOT)
Saved PC:0x40380786
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fcd6100,len:0x6c
load:0x403ce000,len:0x7ec
load:0x403d0000,len:0x2170
entry 0x403ce000
Pro cpu up.
```
However, the system stucks in a exception/printf loop. ESP32-C3 and ESP32-S3 are affected.
### Testing procedure
Flash a ESP32-C3 or ESP32-S3 board that don't have a USB-to-UART chip with reset logic on board, for example
```
BOARD=hip-badge make -j8 -C tests/shell flash
```
or
```
BOARD=esp32s3-pros3 make -j8 -C tests/shell flash
```
Connect a terminal to the the board. Without the PR, the console doesn't seem to work and the RESET button has to pressed explicitly to get it working. With the PR, the console should work.
The problem can also be caused when using
```
dist/tools/esptools/espreset.py -p /dev/ttyACM0
```
while connected with a terminal to the board. Without the PR, the console output stops after
```
ESP-ROM:esp32c3-api1-20210207
Build:Feb 7 2021
rst:0x15 (USB_UART_CHIP_RESET),boot:0xd (SPI_FAST_FLASH_BOOT)
Saved PC:0x40380786
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fcd6100,len:0x6c
load:0x403ce000,len:0x7ec
load:0x403d0000,len:0x2170
entry 0x403ce000
Pro cpu up.
```
while it continues with the PR as following:
```
main(): This is RIOT! (Version: 2023.04-devel-713-gcb721-boards/
test_shell.
>
```
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
