There is size difference for atomic_int_fast8 and atomiic_uint_fast8
on FreeBSD, i.e., they match uint32_t with size of 4 bytes instead of
uint8_t with size of 8. Hence, tests/c11_atomics_cpp_compat buildtest
fails on FreeBSD.
The CC26x2 and CC13x2 share the same register definitions, and both are
treated equally in the TI's technical reference manual. [1]
- To avoid confusions in the future I renamed it to `cc26x2_cc13x2`.
- Documentation was updated.
- The `cc1312-launchpad` board that uses the `cc13x2` MCU was updated.
- The `cc1352-launchpad` board that uses the `cc13x2` MCU was updated.
[1]: https://www.ti.com/lit/ug/swcu185d/swcu185d.pdf
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
With the new toolchain version required to fix issue #13133, the compilation of `examples/posix_socket` fails due to a C linkage error in `atomic_base.h`. The reason is that including `drivers/include/mtd.h` in `boards/esp32/board_common.h` inside the `extern C` block finally leads to including `atomic_base.h` inside the `extern C` block which in turn to the C linkage error for the template definitions in this file.
For atmega boards a TX has not actually completed until UDRn is empty
as well as the Transmit Shift Register.
To avoid resetting an UART before a TX has completed we use the TXCn
flash and ISR to set a variables that indicates TX is ongoing. This
allows not reseting the UART while there are ongoing TX pending.
This fixes an issue where part of the last byte is not shifted out
of the TX shift register causing rubish on the first TX following an
uart_init.
The ADC_STATUS_SINGLEACT indicates that an operation is active, while
the ADC_STATUS_SINGLEDV indicates that data is valid.
This fixes ADC returning values of unfinished reads.
Without this change a RIOT application compiled with all-asan will
segfault as RIOT provides its own malloc by default. Add a define for
disabling custom malloc, calloc and realloc implementations and use it
when compiling with all-asan.
ESP32 can be clocked with either a 40 MHz or 26 MHz crystal. Since most boards use a 40 MHz crystal, the configuration was previously fixed to a 40 MHz crystal. This commit changes the crystal from 40 MHz to automatic detection, allowing boards with a 26 MHz crystal like the Sparkfun ESP32 Thing DEV to be used.
- Unecessary definitions are removed.
- Since the 48-bit RTC hardware timer uses a RC oscillator as clock, it is pretty inaccurate and leads to a RTC time deviation of up to 3 seconds per minute. Therefore, a calibration during the boot time determines a correction factor for the 48-bit RTC hardware timer. Function _rtc_time_to_us uses now this correction factor and converts a raw 48-bit RTC time to a corrected time in microseconds. Thus, the 48-bit RTC timer becomes much more accurate, but it can't still reach the accuracy of the PLL driven 64-bit system timer. The Advantage of using RTC over 64-bit sydtem timer is that it also continues in deep sleep mode and after software reset.
- If the 64-bit system timer is used to emulate the RTC timer, it uses the RTC hardware timer to continue its operation after software .
It is possible to use different timers as RTC timer for the periph_rtc module. Either the 48-bit RTC hardware timer is used directly or the PLL driven 64-bit system timer emulates a RTC timer. The latter one is much more accurate. Pseudomodule esp_rtc_timer controlls which timer is used. Only if esp_rtc_timer is enabled explicitly, the 48-bit RTC hardware timer is used. Otherwise the 64-bit sytstem timer is used to emulate the RTC timer.
The explicit call of rtc_init during the CPU start was removed because rtc_init is called within the function periph_init. The display of the system time at startup had to be placed after the call to periph_init.
There is an existing function that returns the system time in us as a 64 bit value. Converting this 64 value in us to a 32 bit value in ms is more easier and uses the complete 32 bit range. Using only the low part of the 64 bit system time in us and dividing it by 1e3 cuts the 32 bit range.
To control the log level and the format of the log output of SDK libraries, a bunch of library-specific printf functions are realized which map the log output from SDK libraries to RIOT's log macros.
The buffer[EHTHERNET_MAX_LEN] used in _esp_wifi_send to convert the iolist of the given packet to a plain buffer for the WiFi interface should not be on the stack to prevent the sending thread's stack from overflowing.
- Using a enum instead of _COUNTER is easier to read
- _COUNTER is also a reserved name; so better not use it to avoid issues
- Split out the pcint code into a static inline function for increased
readability
The bank index and the pin number are not necessarily identical. For all
PCINT banks except for bank 3 bank_idx was used therefore. It was likely
just forgotten to update that for bank 3 as well.
Some ESP8266/ESP8285 modules only work with DOUT SPI flash mode and a SPI flash frequency of 26 MHz. Therefore, these parameters have to be used by default. Otherwise some modules will no boot.
For better compatibility copy most of cortexm_base.ld
and use the same section names.
Only interrupt stacks and the two additional (currently unused)
heap sections are different between the two now.
Both architectures are variants of the ARM architecture and use the same
toolchain.
There is no reason to have such wildly different defaults.
This results in some tests passing that would crash before:
- [x] `tests/pkg_libcose`
- [x] `tests/pkg_qdsa`
- [x] `tests/pkg_relic`
- [x] `tests/pkg_tweetnacl`
- [x] `tests/pthread_tls`
`THREAD_EXTRA_STACKSIZE_PRINTF_FLOAT` is not used anywhere in RIOT
anymore, so just drop it.
Startup information, including board configuration, is only printed when module esp_log_startup is used. This reduces the amount of information that is printed by default to the console during the startup. The user can enable module esp_log_startup to get the additional startup information.
To avoid that murdock times out before tests/pkg_spiffs and tests/pkg_littlefs time out, the configured test timeouts for these tests is reduced to 200 seconds which should be enough. An ESP32 needs an average of 60 seconds for these tests, while an ESP8266 needs in average 100 seconds.
ESP32 nodes can crash during SPI Flash write operations if required parts of the code are not in the IRAM but in the cached SPI Flash memory, which is disabled during the SPI Flash write operations. Therefore, the code of the SPIFFS package and the VFS module are now stored in the IRAM.
Building e.g. gnrc_border_router example on FreeBSD fails due to
missing defines related to sockets. This adds the missing header
<sys/socket.h> to fix compiling.
Now that CPU and CPU_MODEL are defined in the board's Makefile.features
it can be used to determine the available features provided by the
specific model.
Setting up the .data and .bss section happens in arm7_init.c now.
The code was commented out anyway, so just remove it.
Also remove leftover variable declarations that were only used in
the dead code.
To reduce the information that are printed at the console during the startup, special bootloaders are required that suppress the outputs which are only informational. The according bootloader has to be selected during the make process.
Startup information, including board configuration, is only printed when module esp_log_startup is used. This reduces the amount of information that is printed by default to the console during the startup. The user can enable module esp_log_startup to get the additional startup information.
lpc23xx has 2k of battery RAM that is retained in Deep Power Down mode.
To not overwrite that data it must only be initialized on Power On Reset.
However, RSIR looks the same when waking up from Deep Power Down as it does
on the power-on case.
So use 4 bytes of the backup RAM to keep a signature that is only valid if
memory was retained (no power-on Reset).
A small change to the linker script is required so two sections can be
placed into flash.
The UART peripheral clock seems to be sporadically set to wrong value when the CPU clock is changed. In this case, the UART clock is not set to 115.200 kbps but to 96 kbps, so that the output in the console seems like garbage. This can also cause automatic tests to fail. Therefore, the CPU clock is only changed if CONFIG_ESP32_DEFAULT_CPU_FREQ_MHZ defines a different default CPU clock than the one already used at boot time.
The common ADC API dictates that a sample call must return -1 on an
incorrect resolution. The sam0 ADC implementation instead threw an
assertion failure.
The 10 bit DAC on the lpc23xx is very simple.
It only has one channel and can only be mapped to a single pin (P0.26).
After setting the pin mode to DAC no further configuration in needed.
puf_sram only relies on an uninitialized chunk of memory.
This means to enable it we just have to hook up puf_sram_init().
All memory after __bss_end should be uninitialized at startup, so
just use that.
- TI documentation for msp430f1xx is ambiguous regarding length
of some memmory sectors. For some cpu's the acual size is 1/4 byte
smaller than advertised and one of the sectors is actually 256b and
not 512.
ref: https://e2e.ti.com/support/microcontrollers/msp430/f/166/p/798838/2962979#2962979
- Remove the first 256b sector from usage since there is not support for
variable sized pages
- Fix msp430f2617 FLASHPAGE_NUMOFF to represent accesible memory
If the user or the board definition doesn't enable `esp_wifi` or `esp_eth`, `esp_now` is defined as default netdev.
fixup! cpu/esp32: defines esp_now as default netdev
At the end of an ISR, the ATmega code was doing an `thread_yield()` instead of
a `thread_yield_higher()`. This resulted in tests/isr_yield_higher failing.
Fixing this saves a few lines of code, some ROM, and solves the issue.
Names with two leading underscores are reserved in any context of the c
standard, and thus must not be used. This ATmega platform used it however for
defining internal stuff. This commit fixes this.
