17045: sys/coding: add XOR based coding module r=benpicco a=benpicco
19243: cpu/gd32v: add periph_gpio_ll and periph_gpio_ll_irq support r=benpicco a=gschorcht
### Contribution description
This PR provides the `periph_gpio_ll` and `periph_gpio_ll_irq` support for GD32VF103. Level triggered interrupts are emulated.
`periph_gpio_ll_irq` could be split off from this PR as a separate PR if necessary.
### Testing procedure
Use any GD32V board and connect PA0 -> PB0 and PA1 -> PB1 where PA is the output port and PB the input port. With these connections `tests/periph_gpio_ll` should work.
```
BOARD=sipeed-longan-nano make -j8 -C tests/periph_gpio_ll flash term
```
If necessary, change the input and output pins by setting the environment variables and connect the corresponding pins, for example for `seeedstudio-gd32` PA1 -> PB8 and PA8 -> PB9:
```
PIN_OUT_0=1 PIN_OUT_1=8 PIN_IN_0=8 PIN_IN_1=9 BOARD=seedstudio-gd32 make -j8 -C tests/periph_gpio_ll flash term
```
### Issues/PRs references
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19240: tools/doccheck: add simple exclude to doccheck r=benpicco a=kfessel
while doccheck runs for #19228 and #19220, i saw some spikes in memory consumption, turned out that was `grep -Evf dist/tools/doccheck/exclude_patterns` using about 2GB RAM. This PR changes that.
### Contribution description
add `exclude_simple` to `doccheck` drived from `exclude patterns`
`sort`ed and `uniq`ued the simple excludes
removes no longer needed patterns from `exclude patterns`
simple excludes are string rules (no patterns just strings)
how to apply these:
in this PR:
*remove the path and line number from the rule
* that made some of them doubles of each other
* sorted and uniqued them.
* this set of excludes is no longer path specific (an exception covers all paths but may of them still contain a file name)
another possible solution would be to have the excludes line number specific.
### Testing procedure
run `dist/tools/doccheck/check.sh`
compare memory consumption of
master: `grep -Evf dist/tools/doccheck/exclude_patterns`
to
this PR: `grep -Fvf dist/tools/doccheck/exclude_simple`
### Issues/PRs references
19248: cpu/gd32v: add periph_dac support r=benpicco a=gschorcht
### Contribution description
This PR provides the `periph_dac` support for GD32VF103.
### Testing procedure
`tests/periph_dac` should work on `sipeed-longan-nano` port on PA4 and PA5.
### Issues/PRs references
19255: boards/esp*: complete SD Card MTD config r=benpicco a=gschorcht
### Contribution description
This PR provides the remaining changes necessary to use the generic MTD SD Card configuration as described in PR #19216.
This includes defining the MTD offset for SD cards, since the default `MTD_0` device always uses the internal flash device, and the completion of the configuration for the ESP32 boards with a SD card interface.
### Testing procedure
`tests/vfs_default` should work now with SD Cards:
```
main(): This is RIOT! (Version: 2023.04-devel-323-gfcc07)
mount points:
/nvm0
/sd0
data dir: /sd0
> vfs df
Mountpoint Total Used Available Use%
/nvm0 3052 KiB 8 KiB 3044 KiB 0%
/sd0 7580 MiB 3632148992 B 21089792 B 99%
```
### Issues/PRs references
Co-authored-by: Karl Fessel <karl.fessel@ovgu.de>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19251: tests/driver_dac_dds: fix output of sine and saw functions r=benpicco a=benpicco
19254: cpu/gd32v: add periph_rtc_mem support r=benpicco a=gschorcht
### Contribution description
This PR provides the `periph_rtc_mem` support for GD32VF103.
A modified version of this driver could also be used for STM32F1.
### Testing procedure
`tests/periph_rtt` should work on any GD32V board, for example:
```
BOARD=sipeed-longan-nano make -C tests/periph_rtt flash
```
```
Help: Press s to start test, r to print it is ready
START
main(): This is RIOT! (Version: 2023.04-devel-319-gebc86-cpu/gd32v/periph_rtc_mem)
RIOT RTT low-level driver test
RTT configuration:
RTT_MAX_VALUE: 0xffffffff
RTT_FREQUENCY: 32768
Testing the tick conversion
Trying to convert 1 to seconds and back
Trying to convert 256 to seconds and back
Trying to convert 65536 to seconds and back
Trying to convert 16777216 to seconds and back
Trying to convert 2147483648 to seconds and back
All ok
Initializing the RTT driver
RTC mem OK
This test will now display 'Hello' every 5 seconds
RTT now: 1
Setting initial alarm to now + 5 s (163841)
rtt_get_alarm() PASSED
RTC mem OK
```
### Issues/PRs references
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19249: boards/gd32v: improve board definitions r=benpicco a=gschorcht
### Contribution description
This PR provides some small improvements of the existing board definitions for GD32VF103 boards for more flexibel default configurations and documentation of the board peripherals:
- Allow the remapping of SPI0 pins in SPI configuration (ae984b0bea)
- More flexible I2C configuration (0c337583b4)
The default I2C device configuration allows to define up to two I2C devices `I2C_DEV(0)` and `I2C_DEV(1)`. `I2C_DEV(0)` is always defined if the I2C peripheral is enabled by the module `periph_spi`. The second I2C device `I2C_DEV(1)` is only defined if `I2C_DEV_1_USED` is defined by the board. This allows to use the default configuration with one or two I2C devices depending on whether other peripherals are enabled that would collide with the I2C devices.
- More flexible SPI configuration (edbf59e37e)
The default SPI device configuration allows to define up to two SPI devices `SPI_DEV(0)` and `SPI_DEV(1)`. `SPI_DEV(0)` is always defined if the SPI peripheral is enabled by the module `periph_spi`. The second SPI device `SPI_DEV(1)` is only defined if `SPI_DEV_1_USED` is defined by the board. This allows to use the default configuration with one or two SPI devices depending on whether other peripherals are enabled that would collide with the SPI devices.
Furthermore, the CS signal in the SPI configuration is given by a define that can be overriden with another pin if
the default CS signal is connected to an unused hardware.
- Improve ADC config for Sipeed-Longan-Nano (c9c587ee00)
The ADC configuration was too complex. It was hard to follow when certain ADC lines are available. Furthermore, the order of ADC lines did depend on the use of other peripherals. Now, either the TFT display is not connected and all ADC lines are available or the TFT display is connected and the second SPI device is used so that only the first 4 ADC lines are available.
- Improve Kconfig for Sipeed-Longan-Nano (025f4fdf00)
Board-specific configuration not shown any longer directly in the top level menu but within a submenu.
- Improve peripherals documentation (7f0d560dd8, e24abe495a)
Available peripherals for the board are now documented in two tables ordered by RIOT peripheral names and by pins.
Although the different changes are small and mostly related to the documentation, I could split the PR if necessary.
### Testing
Green CI
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19088: boards: add esp32s3-pros3 support r=benpicco a=gschorcht
### Contribution description
This PR provides the support for [ESP32 ProS3](https://esp32s3.com/pros3.html#home) board from Unexpected Maker.
This board doesn't have a USB-to-Serial chip on board. Therefore, USB Serial/JTAG is used for STDIO and the board is flashed via the USB Seral/JTAG interface by default.
### Testing procedure
Flashing `tests/shell` should work.
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
This implements the XOR based error-correction code described by
Jürgen Fitschen (@jue89) at the RIOT Summit.
A parity byte is generated for each 3 payload bytes, then the payload array
is transposed by interpreting it as a 2D matrix with height of 3.
This is to reduce the chance of consecutive bytes ending up in the same
packet.
This allows to recover one in 3 lost data packets (if parity packets are received).
[0] https://summit.riot-os.org/2021/wp-content/uploads/sites/16/2021/09/s02-01.pdf
After a reset, it can take several seconds before the CDC ACM interface becomes available as serial device `ttyACMx`. This was a change that was already made for `stdio_cdc_acm` in #19128.
Even if only `stdio_usb_serial_jtag` is enabled as STDIO, `usb_board_reset` is enabled since there should be a CDC ACM interface in any case. This is necessary, for example, to reset the board into bootloader if `stdio_cdc_acm` or `stdio_tinyusb_cdc_acm` was previously used.
The ADC configuration was too complex. It was hard to follow when certain ADC lines are available. Furthermore, the order of ADC lines did depend on the use of other peripherals. Now, either the TFT display is not connected and all ADC lines are available or the TFT display is connected and the second SPI device is used so that only the first 4 ADC lines are available.
The default SPI device configuration allows to define up to two SPI devices `SPI_DEV(0)` and `SPI_DEV(1)`. `SPI_DEV(0)` is always defined if the SPI peripheral is enabled by the module `periph_spi`. The second SPI device `SPI_DEV(1)` is only defined if `SPI_DEV_1_USED` is defined by the board. This allows to use the default configuration with one or two SPI devices depending on whether other peripherals are enabled that would collide with the SPI devices.
Furthermore, the CS signal in the SPI configuration is given by a define that can be overriden with another pin if
the default CS signal is connected to an unused hardware.
The default I2C device configuration allows to define up to two I2C devices `I2C_DEV(0)` and `I2C_DEV(1)`. `I2C_DEV(0)` is always defined if the I2C peripheral is enabled by the module `periph_spi`. The second I2C device `I2C_DEV(1)` is only defined if `I2C_DEV_1_USED` is defined by the board. This allows to use the default configuration with one or two I2C devices depending on whether other peripherals are enabled that would collide with the I2C devices.
19244: Make: Add generate-Makefile.ci r=maribu a=bergzand
### Contribution description
This is the same as the create-Makefile.ci. The alias is added to stay in line with other generate-* Make targets. Now the documentation should also be valid again
### Testing procedure
The target should now match the documentation in the doxygen.
### Issues/PRs references
follow-up to #19239
Co-authored-by: Koen Zandberg <koen@bergzand.net>
