This is still currently a hack to hardcode it as the value can be deduced
from the `BOARD_MODULE` daughter board name.
But it requires more cleanup and could come in a separate step.
Part of moving CPU/CPU_MODEL definition to Makefile.features to have it
available before Makefile.include.
The board is deprecated, no need to ignore this board anymore here.
Having the `arduino` and `periph_pwm` features is now required for all
boards using 'arduino-atmega' (as it was except for that board).
If this should change in the future, it should be defined either in each
arduino board, in another board common, or per CPU_MODEL.
This change is for all boards with a sam0 cpu. This cpu just has one ADC.
It is unnecessary to have defines with ADC_0_ prefix as if multiple ADCs
are possible.
Some defines were not used, such as ADC_0_EN, ADC_0_CHANNELS,
ADC_MAX_CHANNELS, ADC_0_CLK_SOURCE, ADC_0_CHANNELS
Change all ADC_0_ prefixes to ADC_
- periph_conf_common.h contains peripherals configuration common to all mkr boards
- periph_conf.h is specific to a subset of mkr boards (mkr1000 and mkrzero)
- Created new `bluepill-128kib` as 128KiB version of the `bluepill`
- Created new `blackpill-128kib` as 128KiB version of the `blackpill`
- Updated `openocd.cfg` to allow flashing 128KiB of ROM
cpu/$(CPU)/Makefile.features and cpu/$(CPU)/Makefile.dep are
automatically included
Part of moving CPU/CPU_MODEL definition to Makefile.features to have it
available before Makefile.include.
cpu/$(CPU)/Makefile.features and cpu/$(CPU)/Makefile.dep are
automatically included
Part of moving CPU/CPU_MODEL definition to Makefile.features to have it
available before Makefile.include.
* CPU files should already have 'CPU' defined by the board.
* Do not conditionally define CPU as it is not needed.
This is part of cleanup prior to moving the CPU/CPU_MODEL to
Makefile.features.
When flashing some applications the flasher sometimes gets stuck which
prevents flashing after.
It may be from a specific firmware or operation but do not have one yet.
Connect with reset asserted fix flashing from this state.
- Moved compiler & linker flags from boards/common/msba2 to cpu/arm7_common
- Moved dependency to newlib nano to cpu/arm7_common
- Moved config to link in cpu/startup.o to cpu/arm7_common
Enable the handling of flashing `softdevice.hex` when flashing the firmware
for openocd.
However, for flashing, only the `hexfile` and `binfile` can currently be used.
The `elffile` is generated with local pages aligned to `0x10000` which makes
the program starting at `0x1f000` be flashed from `0x10000` with padding bytes
even if the `.text` section is indeed at `0x1f000`:
readelf --sections bin/nrf52dk/gnrc_networking.elf
...
[ 1] .text PROGBITS 0001f000 00f000 00f698 00 AX 0 0 16
...
readelf --segments bin/nrf52dk/gnrc_networking.elf
...
LOAD 0x000000 0x00010000 0x00010000 0x1e6a0 0x1e6a0 R E 0x10000
...
The padding bytes would go through `verify_image` in `openocd` so be expected
to not be overwritten but are by `softdevice.hex`
Using --nmagic at link time removes the local page alignement but would
need dedicated testing.
Use the new OPENOCD_RESET_USE_CONNECT_ASSERT_SRST to configure
'reset_config connect_assert_srst' when flashing and resetting only.
This removes the need for a special debug configuration and should allow
connecting to a running target again.
