When a timer is set, any pending interrupts must be cleared before the interrupt is enabled for the channel. Otherwise the interrupt would be triggered immediately when the timer is set.
19185: cpu/gd32v: add periph_gpio_irq support r=gschorcht a=gschorcht
### Contribution description
This PR provides the `periph_gpio_irq` support and is one of a bunch of follow up PRs that complete the peripheral drivers for GD32VF103.
### Testing procedure
Use a GD32VF103 board and flash `tests/periph_gpio`. Note: The Sipeed Longan Nano works also with `seeedstudio-gd32` board defintion and could be used for testing.
```
BOARD=seeedstudio-gd32 make -C tests/periph_gpio flash (until PR #19170 is merged only `seeedstudio
```
With the GPIO PB8 and PB9 connected, the following test sequence should work:
```
> init_out 1 8
> init_int 1 9 2 0
GPIO_PIN(1, 9) successfully initialized as ext int
> set 1 8
INT: external interrupt from pin 9
> clear 1 8
INT: external interrupt from pin 9
```
### Issues/PRs references
19187: cpu/gd32v: add pm_layered support in periph_pm r=gschorcht a=gschorcht
### Contribution description
This PR provides the `pm_layered` support and is one of a bunch of follow up PRs that complete the peripheral drivers for GD32VF103.
Since the configuration of the deep sleep and the standby mode require the access CSR (control and status registers) of the MCU, the Nuclei-SDK NMSIS is added as package which provides a low-level interface for Nuclei-based RISC-V MCUs.
### Testing procedure
The best way to test it is to rebase this PR onto PR #19186 and to flash `tests/periph_pm` to any GD32VF103 board. Note: The Sipeed Longan Nano works also with `seeedstudio-gd32` board definition and could be used for testing.
```
BOARD=seeedstudio-gd32 make -C tests/periph_pm flash
```
The test output should be:
```
main(): This is RIOT! (Version: 2023.04-devel-174-g7dc91-cpu/gd32v/periph_pm_test)
...
mode 0 blockers: 1
mode 1 blockers: 2
mode 2 blockers: 0
Lowest allowed mode: 2
```
Using command the `set_rtc 1 5` command should let the MCU deep sleep for 5 seconds
```
> set_rtc 1 5
Setting power mode 1 for 5 seconds.
␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀>
```
while command `set_rtc 1 5` should set the MCU into the standby mode which is left with restart.
```
> set_rtc 0 5
Setting power mode 0 for 5 seconds.
main(): This is RIOT! (Version: 2023.04-devel-174-g7dc91-cpu/gd32v/periph_pm_test)
...
mode 0 blockers: 1
mode 1 blockers: 2
mode 2 blockers: 0
Lowest allowed mode: 2
>
```
The garbage on UART interface after deep sleep is caused by the clock synchronisation that becomes necessary after deep sleep and is the same as for other boards.
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
This adds support for the gd32v class devices from Gigadevice. The
gd32vf103 contains an 108 MHz RISC-V core with similar peripherals as
the stm32f1 devices
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
