When using `make flash` or `make term` with `MOST_RECENT_PORT=1`, RIOT
should now only consider plausible TTYs and select the most recently
connected one. The filter is a bit broad, though, and will match
any board with a CH430 UART2USB bridge. But depending on the boards
attached, it might be good enough to reliably tell it apart from
other boards.
When using `make flash` or `make term` with `MOST_RECENT_PORT=1`, RIOT
should now only consider plausible TTYs and select the most recently
connected one. The filter is a bit broad, though, and will match
any board with a CH430 USB 2.0 UART2USB bridge. But depending on the
boards attached, it might be good enough to reliably tell it apart from
other boards.
When using `make flash` or `make term` with `MOST_RECENT_PORT=1`, RIOT
should now only consider plausible TTYs and select the most recently
connected one. The filter is a bit broad, though, and will match
any board with a CP2104 USB2UART bridge. But depending on the boards
attached, it might be good enough to reliably tell it apart from other
boards.
When using `make flash` or `make term` with `MOST_RECENT_PORT=1`, RIOT
should now only consider plausible TTYs and select the most recently
connected one. The filter is a bit broad, though, and will match
any board with a CP2102N USB2UART bridge. But depending on the boards
attached, it might be good enough to reliably tell it apart from other
boards.
When using `make flash` or `make term` with `MOST_RECENT_PORT=1`, RIOT
should now only consider plausible TTYs and select the most recently
connected one. The filter is a bit broad, though, and will match
any board with a CP2102 USB2UART bridge. But depending on the boards
attached, it might be good enough to reliably tell it apart from other
boards.
When using `make flash` or `make term` with `MOST_RECENT_PORT=1`, RIOT
should now select relatively robustly the most recently connected
ESP32 Ethernet Kit / ESP32 Wrover Kit board, even with other TTYs
present. This is because the FTDI Dual RS232-HS with two USB2UART
bridges in the chip would be an expensive overkill for most boards,
unless one is using the FTDI chip to big-bang JTAG as well - as done
on the Ethernet Kit and Wrover Kit boards.
The board have one user button and a user led but are not enabled.
This add necessary support to use the button and the led. It include
the configs to use with SAUL and button interrupt.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
- nRF51: Use `uart_conf_t` for consistency with nRF52
- nRF52832: Use UARTE (UART with EasyDMA) over UART (without DMA), as
done for all other nRF52 family members
- use `UARTE_PRESENT` to detect whether an UARTE can be used, rather
than family names
The `SWJ_CFG` field of the `AFIO_MAPR` register is write only and values
read are undefined (random). Hence, using `AFIO->MAPR |= mask;` to
enable flags can corrupt the state of the `SWJ_CFG` (configure it to
an unintended value).
Two helper functions have been introduced:
- `afio_mapr_read()` reads the value, but sanitizes the `SWJ_CFG` field
to zero
- `afio_mapr_write()` writes the given value, but applies the `SWJ_CFG`
configured by the board before writing.
Finally, the `nucleo-f103rb` and `bluepill*`/`blackpill*` boards have
been updated to no longer specify `STM32F1_DISABLE_JTAG`, as this
is handled by the `SWJ_CFG` setting (which defaults to disabling JTAG).
The macro `ARDUINO_SPI_D11D12D13` is used to refer to the SPI bus
on the pins D11/D12/D13 on Arduino UNO compatible boards. For all
Nucleo64 boards this is `SPI_DEV(0)`, but for this board `SPI_DEV(0)`
is internally connected to the radio. Instead `SPI_DEV(1)` is connected
to the correct pins. This provides the macro explicitly in
`periph_conf.h`, which takes preference over the fallback in
`boards/common/nucleo64` when provided.
20003: coap: create typedef for CoAP methods r=benpicco a=benpicco
20028: nanocoap: fix incorrect uses of coap_get_code() r=benpicco a=benpicco
20036: boards/nucleo-l4r5zi : add PWM configuration r=benpicco a=krzysztof-cabaj
### Contribution description
This PR adds to the Nucleo-l4r5zi PWM configuration
### Testing procedure
Flash the board using `tests/periph/pwm` program. Check if you could, for example, change LED
intensity using PWM.
### Issues/PRs references
None.
20041: pkg/littlefs2: bump to v2.8.1 r=benpicco a=bergzand
### Contribution description
Minor version number bump.
### Testing procedure
- Check if I copied the correct commit hash.
- Run the tests.
### Issues/PRs references
None
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: krzysztof-cabaj <kcabaj@gmail.com>
Co-authored-by: Koen Zandberg <koen@bergzand.net>
20032: boards/nucleo-l552ze: add PWM configuration r=benpicco a=krzysztof-cabaj
### Contribution description
This PR adds to the Nucleo-l552ze-q PWM configuration
### Testing procedure
Flash the board using `tests/periph/pwm` program. Check if you could, for example, change LED
intensity using PWM.
### Issues/PRs references
None.
Co-authored-by: krzysztof-cabaj <kcabaj@gmail.com>
