- Before, HSI was enabled as the default case when it is only
used for stm32f0 and stm32f1. It is now implemented explicitly
for those platforms, and only those.
Rational: the periph_common module is required by (most) other periph drivers
and also during startup of the CPU/MCU to run periph_init. The latter is only
required if other periph drivers are used, hence periph_common should be a
depency of periph_* modules and *not* of the CPU/MCU. This PR fixes that
by making periph_common a depency of periph_* and removing the explicit
include in the CPU/MCU implementation.
This driver is compliant with the candev interface. It has been tested
with STM32F0 and STM32F2 and STM32F413 ONLY at this time but should be
compliant with other STM32Fx devices
There is an error when the start byte NACKs
The nack sets the stop bit twice which keeps the stop bit high the next time
When the stop bit is high it creates a timeout when trying to use
This commit fixes so when a NACK occures on the address it doesn't stop twice
USART_CR1_M combines both USART_CR1_M0 and USART_CR1_M1 macros
affecting bits 12 and 28 on 7 data bits capable UARTs. Whereas
for other UARTs USART_CR1_M macro affects only bit 12.
This patch fixes wrong data bits usage on 7 data bits capable
UARTs with using USART_CR1_M0 macro for modes 8-E-x and 8-O-x.
It also simplifies bits unsetting as USART_CR1_M macro clears
all data bits related bits for both UART types.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Add support for specifying data bits, stop bits and parity at
runtime.
Introduce feature periph_uart_modecfg for uart_mode() till all
other CPUs implement it.
STM32 L1, F1, F2, F4 supports following modes:
* 7E1, 7E2
* 7O1, 7O2
* 8N1, 8N2
* 8E1, 8E2
* 8O1, 8O2
STM32 L0, L4, F0, F3, F7 supports following modes:
* 6E1, 6E2
* 6O1, 6O2
* 7E1, 7E2
* 7O1, 7O2
* 7N1, 7N2
* 8N1, 8N2
* 8E1, 8E2
* 8O1, 8O2
Use USART_CR1_M1 macro to detect 7-bit support because
even inside one family there could be devices that don't
support 7-bit mode. So just using a family macro is not
enough.
As stated in the datasheets for L0, L4, F0, F3, F7 devices,
data bits can only be changed when UART is disabled (UE=0).
Introduce uart_stop() routine to satisfy this requirement.
STM32 UART adds parity to the MSB of a byte to send. The same
also applies to the received bytes. As a result this bit must
be masked in order to get the pure data.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Refactors i2c_2 to match the structure of i2c_1 better.
Corrects functionality issues.
Allows the common implementation of read_regs and write_regs.
Documents constraints of hardware.
Matches error messages with API.
Due to the stdio getting called after periph_init the uart may send before initialized.
This adds a simple check so the uart does not get into a locked-up state.
This commit fixes configuration problems when trying to use i2c pins that need to be remapped.
All B8 and B9 pins for STM32F1 need to be remapped, so a check is done if the remappable pins are selected.
