To reduce the information that are printed at the console during the startup, special bootloaders are required that suppress the outputs which are only informational. The according bootloader has to be selected during the make process.
Startup information, including board configuration, is only printed when module esp_log_startup is used. This reduces the amount of information that is printed by default to the console during the startup. The user can enable module esp_log_startup to get the additional startup information.
lpc23xx has 2k of battery RAM that is retained in Deep Power Down mode.
To not overwrite that data it must only be initialized on Power On Reset.
However, RSIR looks the same when waking up from Deep Power Down as it does
on the power-on case.
So use 4 bytes of the backup RAM to keep a signature that is only valid if
memory was retained (no power-on Reset).
A small change to the linker script is required so two sections can be
placed into flash.
The UART peripheral clock seems to be sporadically set to wrong value when the CPU clock is changed. In this case, the UART clock is not set to 115.200 kbps but to 96 kbps, so that the output in the console seems like garbage. This can also cause automatic tests to fail. Therefore, the CPU clock is only changed if CONFIG_ESP32_DEFAULT_CPU_FREQ_MHZ defines a different default CPU clock than the one already used at boot time.
The common ADC API dictates that a sample call must return -1 on an
incorrect resolution. The sam0 ADC implementation instead threw an
assertion failure.
The 10 bit DAC on the lpc23xx is very simple.
It only has one channel and can only be mapped to a single pin (P0.26).
After setting the pin mode to DAC no further configuration in needed.
puf_sram only relies on an uninitialized chunk of memory.
This means to enable it we just have to hook up puf_sram_init().
All memory after __bss_end should be uninitialized at startup, so
just use that.
- TI documentation for msp430f1xx is ambiguous regarding length
of some memmory sectors. For some cpu's the acual size is 1/4 byte
smaller than advertised and one of the sectors is actually 256b and
not 512.
ref: https://e2e.ti.com/support/microcontrollers/msp430/f/166/p/798838/2962979#2962979
- Remove the first 256b sector from usage since there is not support for
variable sized pages
- Fix msp430f2617 FLASHPAGE_NUMOFF to represent accesible memory
If the user or the board definition doesn't enable `esp_wifi` or `esp_eth`, `esp_now` is defined as default netdev.
fixup! cpu/esp32: defines esp_now as default netdev
At the end of an ISR, the ATmega code was doing an `thread_yield()` instead of
a `thread_yield_higher()`. This resulted in tests/isr_yield_higher failing.
Fixing this saves a few lines of code, some ROM, and solves the issue.
Names with two leading underscores are reserved in any context of the c
standard, and thus must not be used. This ATmega platform used it however for
defining internal stuff. This commit fixes this.
To be able to catch a core panic in debugger and to get the last output from asynchronous UART , e.g., if the stack is smashed, the system is not rebooted immediately anymore but breaks, which stops the execution in debugger or reboots the system after WDT timeout.
Log outputs generated by binary ESP32 SDK libraries are mapped to the ESP32's log module which supports colored and tagged log outpus. Tagged log outputs from SDK libraries are handled accordingly.
The implementation of `log_module` for ESP32 was changed from functions to a macro-based implementation to be able to use the bunch of macros for colored and tagget log output generation.
Enable IDLE and Deep Powerdown mode.
IDLE is pretty straightforward - insteady of busy waiting, the CPU will
enter an idle state from which it will resume on any event.
Deep Power Down shuts off the entite system except for the battery backup
power domain.
That means the CPU will reset on resume and can be woken by e.g. RTC.
SLEEP and POWERDOWN disable the PLL and the PLL and Flash respectively.
This requires some proper wake-up handling.
Since this turned out to be a major time sink and those modes are never
currently never used in RIOT outside of tests, I left this as an exercise
for a future reader.
`pm_set()` gets called by the idle thread whose stack is too small
for normal DEBUG()/printf().
Use DEBUG_PUTS() instead to print the static debug strings.
Renames crypto functions of ESP32 SDK in vendor code to resolve the conflicts between `wpa-supplicant` crypto functions and RIOT's `crypto` and `hashes` modules.
To resolve the conflicts between `wpa-supplicant` crypto functions (part of the ESP32 SDK) and RIOT's `crypto` and `hashes` modules, the crypto function headers from ESP32 SDK are added to vendor code and the crypto functions are renamed using the prefix `wpa_`.
A number of tests insist that the number of thread priority levels is 16. However, when using the WiFi interface, a number of high priority threads are required to handle the WiFi hardware. In this case, the number of thread priority levels must be 32. Solves the problem of tests `tests/shell`.
Removes the dependency of the module riot_freertos from module xtimer. This avoids that xtimer is used even if it is not really needed which in turn occupies the first timer device and tests/periph_timer fails.
ESP32 log output was always tagged with additional information by default. The tag consists the type of the log message, the system time in ms, and the module or function in which the log message is generated. By introducing module `esp_log_tagged`, these additional information are disabled by default and can be enabled by using module `esp_log_tagged`.
Log module of ESP32 supports colored log outputs when module `esp_log_color` is enabled. The generation of colored log outputs is realized by a extending the bunch of macros with an additional letter indicating the type of log message,
For the implementation of the colored log output, two versions of the bootloader are introduced, one version with colored log output and one version without colors.
