mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2024-12-29 04:50:03 +01:00
75 lines
2.5 KiB
Plaintext
75 lines
2.5 KiB
Plaintext
/**
|
|
@defgroup boards_nucleo-f030r8 STM32 Nucleo-F030R8
|
|
@ingroup boards_common_nucleo64
|
|
@brief Support for the STM32 Nucleo-F030R8
|
|
|
|
## Overview
|
|
|
|
The Nucleo-F030 is a board from ST's Nucleo family supporting a ARM Cortex-M0
|
|
STM32F030R8 microcontroller with 8Kb of SRAM and 64Kb of ROM Flash.
|
|
|
|
## Hardware
|
|
|
|
|
|
|
|
|
|
|
|
### MCU
|
|
| MCU | STM32F030R8 |
|
|
|:------------- |:--------------------- |
|
|
| Family | ARM Cortex-M0 |
|
|
| Vendor | ST Microelectronics |
|
|
| RAM | 8Kb |
|
|
| Flash | 64Kb |
|
|
| Frequency | up to 48MHz) |
|
|
| FPU | yes |
|
|
| Timers | 11 (2x watchdog, 1 SysTick, 8x 16-bit) |
|
|
| ADCs | 1x 12-bit |
|
|
| UARTs | 6 |
|
|
| SPIs | 2 |
|
|
| I2Cs | 2 |
|
|
| RTC | 1 |
|
|
| Vcc | 2.0V - 3.6V |
|
|
| Datasheet | [Datasheet](http://www.st.com/en/evaluation-tools/nucleo-f030r8.html) |
|
|
| Reference Manual | [Reference Manual](http://www.st.com/resource/en/datasheet/stm32f030r8.pdf) |
|
|
| Programming Manual | [Programming Manual](http://www.st.com/resource/en/programming_manual/dm00051352.pdf) |
|
|
| Board Manual | [Board Manual](http://www.st.com/resource/en/user_manual/dm00105823.pdf)|
|
|
|
|
|
|
|
|
## Implementation Status
|
|
| Device | ID | Supported | Comments |
|
|
|:------------- |:------------- |:------------- |:------------- |
|
|
| MCU | STM32F030R8 | partly | Energy saving modes not fully utilized |
|
|
| Low-level driver | GPIO | yes | |
|
|
| | PWM | yes (4 pins available) | |
|
|
| | UART | 2 UARTs | USART2 via STLink/USB or D0(RX)/D1(TX) and USART1 on PA10(RX)/PA09(TX) |
|
|
| | ADC | 6 pins | |
|
|
| | I2C | no | |
|
|
| | SPI | no | |
|
|
| | USB | no | |
|
|
| | Timer | 3 16 bit timers | |
|
|
|
|
|
|
## Flashing the device
|
|
The ST Nucleo-F030 board includes an on-board ST-LINK V2 programmer. The
|
|
easiest way to program the board is to use OpenOCD. Once you have installed
|
|
OpenOCD (look [here](https://github.com/RIOT-OS/RIOT/wiki/OpenOCD) for
|
|
installation instructions), you can flash the board simply by typing
|
|
|
|
```
|
|
make BOARD=nucleo-f030 flash
|
|
```
|
|
and debug via GDB by simply typing
|
|
```
|
|
make BOARD=nucleo-f030 debug
|
|
```
|
|
|
|
|
|
## Supported Toolchains
|
|
For using the ST Nucleo-F030 board we strongly recommend the usage of the
|
|
[GNU Tools for ARM Embedded Processors](https://launchpad.net/gcc-arm-embedded)
|
|
toolchain.
|
|
*/
|