The address in the USB device can be set either directly after the SETUP stage on receipt of the `SET ADDRESS Request` or after the associated status stage. When the USB device address has to be set depends on the hardware. If `USBDEV_SET_ADDR_AFTER_STATUS` has the value 1 (default), the address is only set in the USB device after the status stage. Overwrite it with 0 in `periph_cpu.h` to set the address already directly after the SETUP stage.
This commit adds dedicated stall functions for usbdev peripherals. Two
functions are added. The first function (usbdev_ep_stall) to enable and
disable the stall condition on generic endpoints. The second function is
a dedicated function to set the stall condition on endpoint zero in both
directions. This status can only be set and should automatically be
cleared by the usbdev implementation (or hardware) after a new setup
request is received from the host.
This is a temporary fix for Issue #17060. It allows to disable
auto inclusion of `ztimer_periph_rtt` in cases where another
module or application requires direct access.
Limitations:
- as ifeq are involved order of inclusion matters, therefore
these modules should be included early in the build at application
level and not in modules `Makefile.dep`
- this does not disallow direct inclusions of `ztimer_periph_rtt`,
since this only disables auto inclusion of these modules
This is a temporary solution since this is already possible with
Kconfig, but not in make.
Since all implementations simply return 0 and most drivers do not check the return value, it is better to return void and use an assert to ensure that the given device identifier and given device parameters are correct.
The default driver type is just an index into a device array defined
by the board.
If a platform wants to encode additional information in the device type,
it can define a custom type.
This means we can just set the default type to whatever fits the target
CPU best.
On ARM this will still be a 32 bit word, but on AVR it will by a 8 bit byte.
This API change refactors the usbdev API to supply buffers via the
usbdev_ep_xmit function. This changes from the usbdev_ep_ready call to allow
separate buffers per call. An usbdev_ep_buf_t pseudotype is available and must
be used when defining buffers used for endpoints to adhere to the DMA alignment
restrictions often required with usb peripherals.
Main advantage is that the usbdev peripherals no longer have to allocate
oversized buffers for the endpoint data, potentially saving multiple KiB
of unused buffer space. These allocations are now the responsibility of
the individual USB interfaces in the firmware
This API change refactors the usbdev API to supply buffers via the
usbdev_ep_xmit function. This changes from the usbdev_ep_ready call to allow
separate buffers per call. An usbdev_ep_buf_t pseudotype is available and must
be used when defining buffers used for endpoints to adhere to the DMA alignment
restrictions often required with usb peripherals.
Main advantage is that the usbdev peripherals no longer have to allocate
oversized buffers for the endpoint data, potentially saving multiple KiB
of unused buffer space. These allocations are now the responsibility of
the individual USB interfaces in the firmware
There is no way to properly handle incorrect SPI parameters at run time, so
just having an assertion blow up is the better choice here.
As most instances of `spi_acquire()` don't check the return value anyway, this
will improve debugging experience quite a bit. Some implementation of
spi_acquire() don't even check parameters anyway.
Some terminology issues are fixed. (The speed of an UART interface is
the symbol rate. The unit it is measured in is baud, which is symbols
per second. There is no such thing as baudrate or even baud/s.)
The return codes are changed to use negative errno constants on error
to match the driver design rules. For backward compatibility, the
enum was updated to match the error codes. Unless an application
depends on the exact numerical value (which would be insane), this is
not breaking any code.
RTC on RTT usually runs at a frequency greater than 1 Hz, so sub-second
precision is available.
Add a function to get the current RTC timestamp together with it's sub-second
component.
Some periph_rtt implementations do not provide `rtt_set_counter()`. This
adds `periph_rtt_set_counter` as feature to allow testing for its
availability. The feature is provided at CPU level if periph_rtt is
provided by the board for all CPUs implementing `rtt_set_counter()`.
