- Unecessary definitions are removed.
- Since the 48-bit RTC hardware timer uses a RC oscillator as clock, it is pretty inaccurate and leads to a RTC time deviation of up to 3 seconds per minute. Therefore, a calibration during the boot time determines a correction factor for the 48-bit RTC hardware timer. Function _rtc_time_to_us uses now this correction factor and converts a raw 48-bit RTC time to a corrected time in microseconds. Thus, the 48-bit RTC timer becomes much more accurate, but it can't still reach the accuracy of the PLL driven 64-bit system timer. The Advantage of using RTC over 64-bit sydtem timer is that it also continues in deep sleep mode and after software reset.
- If the 64-bit system timer is used to emulate the RTC timer, it uses the RTC hardware timer to continue its operation after software .
It is possible to use different timers as RTC timer for the periph_rtc module. Either the 48-bit RTC hardware timer is used directly or the PLL driven 64-bit system timer emulates a RTC timer. The latter one is much more accurate. Pseudomodule esp_rtc_timer controlls which timer is used. Only if esp_rtc_timer is enabled explicitly, the 48-bit RTC hardware timer is used. Otherwise the 64-bit sytstem timer is used to emulate the RTC timer.
The explicit call of rtc_init during the CPU start was removed because rtc_init is called within the function periph_init. The display of the system time at startup had to be placed after the call to periph_init.
There is an existing function that returns the system time in us as a 64 bit value. Converting this 64 value in us to a 32 bit value in ms is more easier and uses the complete 32 bit range. Using only the low part of the 64 bit system time in us and dividing it by 1e3 cuts the 32 bit range.
To control the log level and the format of the log output of SDK libraries, a bunch of library-specific printf functions are realized which map the log output from SDK libraries to RIOT's log macros.
The buffer[EHTHERNET_MAX_LEN] used in _esp_wifi_send to convert the iolist of the given packet to a plain buffer for the WiFi interface should not be on the stack to prevent the sending thread's stack from overflowing.
Some ESP8266/ESP8285 modules only work with DOUT SPI flash mode and a SPI flash frequency of 26 MHz. Therefore, these parameters have to be used by default. Otherwise some modules will no boot.
For better compatibility copy most of cortexm_base.ld
and use the same section names.
Only interrupt stacks and the two additional (currently unused)
heap sections are different between the two now.
Both architectures are variants of the ARM architecture and use the same
toolchain.
There is no reason to have such wildly different defaults.
This results in some tests passing that would crash before:
- [x] `tests/pkg_libcose`
- [x] `tests/pkg_qdsa`
- [x] `tests/pkg_relic`
- [x] `tests/pkg_tweetnacl`
- [x] `tests/pthread_tls`
`THREAD_EXTRA_STACKSIZE_PRINTF_FLOAT` is not used anywhere in RIOT
anymore, so just drop it.
Startup information, including board configuration, is only printed when module esp_log_startup is used. This reduces the amount of information that is printed by default to the console during the startup. The user can enable module esp_log_startup to get the additional startup information.
To avoid that murdock times out before tests/pkg_spiffs and tests/pkg_littlefs time out, the configured test timeouts for these tests is reduced to 200 seconds which should be enough. An ESP32 needs an average of 60 seconds for these tests, while an ESP8266 needs in average 100 seconds.
ESP32 nodes can crash during SPI Flash write operations if required parts of the code are not in the IRAM but in the cached SPI Flash memory, which is disabled during the SPI Flash write operations. Therefore, the code of the SPIFFS package and the VFS module are now stored in the IRAM.
Building e.g. gnrc_border_router example on FreeBSD fails due to
missing defines related to sockets. This adds the missing header
<sys/socket.h> to fix compiling.
Now that CPU and CPU_MODEL are defined in the board's Makefile.features
it can be used to determine the available features provided by the
specific model.
Setting up the .data and .bss section happens in arm7_init.c now.
The code was commented out anyway, so just remove it.
Also remove leftover variable declarations that were only used in
the dead code.
To reduce the information that are printed at the console during the startup, special bootloaders are required that suppress the outputs which are only informational. The according bootloader has to be selected during the make process.
Startup information, including board configuration, is only printed when module esp_log_startup is used. This reduces the amount of information that is printed by default to the console during the startup. The user can enable module esp_log_startup to get the additional startup information.
