This implements a client for DHCPv6 IA_PD (Identity Association for
Prefix Delegation). Goal was to have a IETF-compliant alternative to
UHCP. The implementation was based on RFC 8415.
- add init_schedstatistics function to be called after
auto_init, that way xtimer_is init is called before
the first call to xtimer_now
- register schedstatics code as a callback to be executed
on each sched_run()
Rename TMP006 to TMP00x
Add TMP007 sensor support to TMP00X
Change uint8_t reg to uint16_t
Add to doxygen documentation group
Expose compile time configurations
Move defines from .c to .h
Change double to float, because double is not needed
Add TMP007 register information
The cc110x driver has been re-written from scratch to overcome the limitations
of the old driver. The main motivation of the rewrite was to achieve better
maintainability by a detailed documentation, reduce the complexity and the
overhead of the SPI communication with the device, and to allow to
simultaneously use transceivers with different configuration regarding the used
base band, the channel bandwidth, the modulation rate, and the channel map.
Features of this driver include:
- Support for the CC1100, CC1101, and the CC1100e sub-gigahertz transceivers.
- Detailed documentation of every aspect of this driver.
- An easy to use configuration API that allows setting the transceiver
configuration (modulation rate, channel bandwidth, base frequency) and the
channel map.
- Fast channel hopping by pre-calibration of the channels during device
configuration (so that no calibration is needed during hopping).
- Simplified SPI communication: Only during start-up the MCU has to wait
for the transceiver to be ready (for the power regulators and the crystal
to stabilize). The old driver did this for every SPI transfer, which
resulted in complex communication code. This driver will wait on start up
for the transceiver to power up and then use RIOT's SPI API like every other
driver. (Not only the data sheet states that this is fine, it also proved to
be reliable in practise.)
- Greatly reduced latency: The RTT on the old driver (@150 kbps data rate) was
about 16ms, the new driver (@250 kbps data rate) has as RTT of ~3ms
(depending on SPI clock and on CPU performance) (measured with ping6).
- Increased reliability: The preamble size and the sync word size have been
doubled compared to the old driver (preamble: 8 bytes instead of 4,
sync word: 4 byte instead of 2). The new values are the once recommended by
the data sheet for reliable communication.
- Basic diagnostic during driver initialization to detect common issues as
SPI communication issues and GDO pin configuration/wiring issues.
- TX power configuration with netdev_driver_t::set() API-integration
- Calls to netdev_driver_t::send() block until the transmission has completed
to ease the use of the API (implemented without busy waiting, so that the
MCU can enter lower power states or other threads can be executed).
- Removed cc110x driver
- Updated all makefiles
- Kept both board specific configurations and support for it in RIOT's
upper layers, so re-implementations don't need to start from zero
stm32eth: Move to stm32_common periph
cpu/stm32_periph_eth: Rebase to current master branch
- Update DMA to use new vendor headers
- Update send to use iolist. It looks like the packet headers are now transfered as seperate iolist entries which results in the eth periph sending each header as own packet. To fix this a rather ugly workaround is used where the whole iolist content is first copied to a static buffer. This will be fixed soon in another commit
- If MAC is set to zero use luid to generate one
- Small code style fixes
cpu/stm312f7: Add periph config for on-board ethernet
boards/nucleo-f767zi: Add config for on board ethernet
tests/stm32_eth_lwip: Remove board restriction
boards/common/nucleo: Add luid module if stm32 ethernet is used
tests/stm32_eth_gnrc: Add Testcase for gnrc using the stm32 eth periph
stm32_eth: Rework netdev driver layour
tests/stm32_eth_*: Use netdev driver header file for prototypes
stm32_eth: Add auto init for stm32 eth netdev driver
boards/stm32: Enable ethernet conf for nucleo boards
stm32_eth_auto_init: Add dont be pendantic flag
stm32_eth: Remove dma specific stuff from periph_cpu.h
Looks like this was implemented in PR #9171 and 021697ae94 with the same interface.
stm32_eth: Remove eth feature from stm32f4discovery boards
stm32_eth: Migrate to stm32 DMA API
stm32_eth: Add iolist to module deps
stm32_eth: Rework send function to use iolist
stm32_eth: Fix ci build warnings
stm32_eth: Fix bug introduced with iolist usage
stm32_eth: Remove redundant static buffer
stm32_eth: Fix feature dependencies
stm32_eth: Fix wrong header guard name
stm32_eth: Implement correct l2 netstats interface
stm32_eth: Rename public functions to stm32_eth_*
stm32_eth: Fix doccheck
stm32_eth: Move register DEFINE to appropriate header file
stm32_eth: remove untested configuration for f446ze boards
stm32_eth: Move periph configuration struct to stm32_common
stm32_eth: Fix naming of eth_phy_read and eth_phy_write
stm32_eth: Remove obsolete test applications
