Use analog mode for GPIO_DISCONNECT, as this is said to have the lowest
current leakage due to disabling the Schmitt trigger and correctly
detect this in `gpio_ll_query_conf()`.
Also drop the `schmitt_trigger_disabled` member in `gpio_conf_t`, as
the Schmitt trigger is only ever disabled in Analog mode anyway and
cannot be freely configured.
This commit optimizes the `gpio_conf_t` type in the following
regards:
- The "base" `gpio_conf_t` is stripped from members that only some
platforms support, e.g. drive strength, slew rate, and disabling of
the Schmitt Trigger are no longer universally available but
platform-specific extensions
- The `gpio_conf_t` is now crammed into a bit-field that is 8 bit or
16 bit wide. This allows for storing lots of them e.g. in
`driver_foo_params_t` or `uart_conf_t` etc.
- A `union` of the `struct` with bit-field members and a `bits` is used
to allow accessing all bits in a simple C statement and to ensure
alignment for efficient handling of the type
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
17045: sys/coding: add XOR based coding module r=benpicco a=benpicco
19243: cpu/gd32v: add periph_gpio_ll and periph_gpio_ll_irq support r=benpicco a=gschorcht
### Contribution description
This PR provides the `periph_gpio_ll` and `periph_gpio_ll_irq` support for GD32VF103. Level triggered interrupts are emulated.
`periph_gpio_ll_irq` could be split off from this PR as a separate PR if necessary.
### Testing procedure
Use any GD32V board and connect PA0 -> PB0 and PA1 -> PB1 where PA is the output port and PB the input port. With these connections `tests/periph_gpio_ll` should work.
```
BOARD=sipeed-longan-nano make -j8 -C tests/periph_gpio_ll flash term
```
If necessary, change the input and output pins by setting the environment variables and connect the corresponding pins, for example for `seeedstudio-gd32` PA1 -> PB8 and PA8 -> PB9:
```
PIN_OUT_0=1 PIN_OUT_1=8 PIN_IN_0=8 PIN_IN_1=9 BOARD=seedstudio-gd32 make -j8 -C tests/periph_gpio_ll flash term
```
### Issues/PRs references
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
16782: drivers/mfrc522: add new driver r=benpicco a=HendrikVE
### Contribution description
This PR adds support for the MFRC522. It is quite common in the Arduino world and it is quite cheap. The driver connects to the MFRC522 via SPI and is heavily based on the Arduino driver available [here](https://github.com/miguelbalboa/rfid). Basically it was ported, but with several improvements in readability and documentation.
### Testing procedure
The given (manual) test provides single commands for some driver functions.
19201: cpu/gd32v: add periph_i2c support r=benpicco a=gschorcht
### Contribution description
This PR provides the `periph_i2c` support and is one of a bunch of PRs that complete the peripheral drivers for GD32VF103.
The driver is a modified version of the driver for STM32F1 with some changes that were necessary to get it working on GD32V. As for STM32F1, the driver is using polling instead of interrupts for now. It will be implemented interrupt-driven later.
### Testing procedure
`tests/periph_i2c` as well as a test with any I2C sensor should work. The driver was tested with `tests/driver_l3gxxxx` and `tests/driver_bmp180`.
### Issues/PRs references
Co-authored-by: Hendrik van Essen <hendrik.ve@fu-berlin.de>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19185: cpu/gd32v: add periph_gpio_irq support r=gschorcht a=gschorcht
### Contribution description
This PR provides the `periph_gpio_irq` support and is one of a bunch of follow up PRs that complete the peripheral drivers for GD32VF103.
### Testing procedure
Use a GD32VF103 board and flash `tests/periph_gpio`. Note: The Sipeed Longan Nano works also with `seeedstudio-gd32` board defintion and could be used for testing.
```
BOARD=seeedstudio-gd32 make -C tests/periph_gpio flash (until PR #19170 is merged only `seeedstudio
```
With the GPIO PB8 and PB9 connected, the following test sequence should work:
```
> init_out 1 8
> init_int 1 9 2 0
GPIO_PIN(1, 9) successfully initialized as ext int
> set 1 8
INT: external interrupt from pin 9
> clear 1 8
INT: external interrupt from pin 9
```
### Issues/PRs references
19187: cpu/gd32v: add pm_layered support in periph_pm r=gschorcht a=gschorcht
### Contribution description
This PR provides the `pm_layered` support and is one of a bunch of follow up PRs that complete the peripheral drivers for GD32VF103.
Since the configuration of the deep sleep and the standby mode require the access CSR (control and status registers) of the MCU, the Nuclei-SDK NMSIS is added as package which provides a low-level interface for Nuclei-based RISC-V MCUs.
### Testing procedure
The best way to test it is to rebase this PR onto PR #19186 and to flash `tests/periph_pm` to any GD32VF103 board. Note: The Sipeed Longan Nano works also with `seeedstudio-gd32` board definition and could be used for testing.
```
BOARD=seeedstudio-gd32 make -C tests/periph_pm flash
```
The test output should be:
```
main(): This is RIOT! (Version: 2023.04-devel-174-g7dc91-cpu/gd32v/periph_pm_test)
...
mode 0 blockers: 1
mode 1 blockers: 2
mode 2 blockers: 0
Lowest allowed mode: 2
```
Using command the `set_rtc 1 5` command should let the MCU deep sleep for 5 seconds
```
> set_rtc 1 5
Setting power mode 1 for 5 seconds.
␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀>
```
while command `set_rtc 1 5` should set the MCU into the standby mode which is left with restart.
```
> set_rtc 0 5
Setting power mode 0 for 5 seconds.
main(): This is RIOT! (Version: 2023.04-devel-174-g7dc91-cpu/gd32v/periph_pm_test)
...
mode 0 blockers: 1
mode 1 blockers: 2
mode 2 blockers: 0
Lowest allowed mode: 2
>
```
The garbage on UART interface after deep sleep is caused by the clock synchronisation that becomes necessary after deep sleep and is the same as for other boards.
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
This adds support for the gd32v class devices from Gigadevice. The
gd32vf103 contains an 108 MHz RISC-V core with similar peripherals as
the stm32f1 devices
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
