- many backports from @maribu's IRQ based implementation (#18591)
- use of ztimer and errno.h
- separation of dht_read() steps into functions for better readability
- reintroduction of DHT11/DHT22 differentiation
- sensor presence checking in dht_init()
- default input mode changed to open drain
- AVR support without platform-specific handling by avoiding
ztimer_spin() and using the overflow of an 8-bit variable as a
pre-timeout to minimize time-consuming ztimer_now() calls
- add a new DHT11_2022 type for 0.01 °C resolution devices
- data caching removed
19650: drivers/nrf24l01p: model in kconfig r=aabadie a=aabadie
19660: cpu/rpx0xx: Fix kconfig model r=aabadie a=MrKevinWeiss
### Contribution description
Broken master due to incorrect model of the periph_pio in kconfig.
### Testing procedure
Green murdock (now that the board is added to the list)
### Issues/PRs references
Look at the master CI...
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
Co-authored-by: MrKevinWeiss <weiss.kevin604@gmail.com>
19618: cpu/stm32: fix riotboot settings for L4 and WB r=benpicco a=gschorcht
### Contribution description
This PR fixes the `riotboot` configuration for L4 and WB.
The family is not called `stm32l4` or `stm32wb` but `l4` and `wb`. That is, the `riotboot` configuration didn't work at all. Furthermore, a minimum `RIOTBOOT_LEN` of `0x2000` is required for L4.
Found when investigating the compilation errors for `bootloaders/riotboot_serial` in PR #19576.
### Testing procedure
1. Green CI.
2. Use the following commands:
```
BOARD=nucleo-l496zg make -C tests/riotboot info-debug-variable-RIOTBOOT_HDR_LEN
BOARD=p-nucleo-wb55 make -C tests/riotboot info-debug-variable-RIOTBOOT_HDR_LEN
```
In master these commands give
```
0x400
```
With this PR these commands give
```
0x200
```
as expected.
3. Use the following commands:
```
BOARD=nucleo-l496zg make -C tests/riotboot info-debug-variable-RIOTBOOT_LEN
BOARD=p-nucleo-wb55 make -C tests/riotboot info-debug-variable-RIOTBOOT_LEN
```
In master these commands give
```
0x1000
```
With this PR these commands give
```
0x2000
```
as expected.
### Issues/PRs references
19639: tests/net/gnrc_mac_timeout: add automated test r=aabadie a=aabadie
19644: gnrc_ipv6_nib: include RIO with all subnets in downstream RA r=benpicco a=benpicco
19649: gnrc_sixlowpan_iphc: prefix bits outside context must be zero r=benpicco a=benpicco
19656: gnrc/ipv6_auto_subnets: allow to configure minimal prefix length r=benpicco a=benpicco
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
- Replace all users of `$(RIOTBASE)/build` with the already present
`$(BUILD_DIR)` variable
- Replace all users of `$(BUILD_DIR)/pkg` with the already present
`$(PKGDIRBASE)` variable
- Create a `CACHEDIR.TAG` file in the `$(BUILD_DIR)`
18056: pkg/cmsis: use unique package for CMSIS headers, DSP and NN modules r=benpicco a=aabadie
19571: cpu/stm32/periph_adc: fixes and improvements for L4 support r=benpicco a=gschorcht
### Contribution description
This PR provides the following fixes and improvements for the `periph_adc` implementation for STM32L4.
- Support STM32L496AG added.
- Instead of defining the number of ADC devices for each MCU model, the number of ADC devices is determined from ADCx definitions in CMSIS header.
- MCU specific register/value defines are valid for all L4 MCUs, model based conditional compilation is removed.
- The ADC clock disable function is fixed using a counter. The counter is incremented in `prep` and decremented in `done`. The ADC clock is disabled if the counter becomes 0.
- For boards that have not connected the V_REF+ pin to an external reference voltage, the VREFBUF peripheral can be used as V_REF+ (if supported) by setting `VREFBUF_ENABLE=1`.
- The ASCR register is available and has to be set for all STM32L471xx, STM32L475xx, STM32L476xx, STM32L485xx and STM32L486xx MCUs. Instead of using the CPU model for conditional compilation, the CPU line is used to support all MCU of that lines.
- Setting of SQR1 is fixed. Setting the SQR1 did only work before because the `ADC_SRQ_L` is set to 0 for a sequence length of 1.
- Setting the `ADC_CCR_CKMODE` did only work for the reset state. It is now cleared before it is set. Instead of using the `ADC_CCR_CKMODE_x` bits to set the mode, the mode defines are used.
- Support for V_REFINT as ADC channel added.
### Testing procedure
19589: gnrc/gnrc_netif_hdr_print: printout timestamp if enabled r=aabadie a=chudov
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: chudov <chudov@gmail.com>
19585: tests: move leftover sys related tests to test/sys + move tests/sys/candev to tests/drivers r=aabadie a=aabadie
19586: tests: move net related applications to test/net r=aabadie a=aabadie
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
19582: tests: move nimble and lwip related to test applications to tests/pkg r=aabadie a=aabadie
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
19573: cpu/stm32/periph_dac: small improvements r=maribu a=gschorcht
### Contribution description
This PR provides the following improvements for `periph_dac` on STM32
- Support for `RCC_APB1ENR1_DAC1EN` symbol added.
- For boards that have not connected the V_REF+ pin to an external reference voltage, the VREFBUF peripheral can be used as V_REF+ (if supported) by setting `VREFBUF_ENABLE=1`.
- If the DAC peripheral has a mode register (`DAC_MCR`), it is set to normal mode with buffer enabled and connected to external pin and on-chip peripherals. This allows to measure the current value of a DAC channel with an ADC channel or to use the DAC channel also for other on-chip peripherals.
### Testing procedure
- Green CI
- `tests/periph_dac` should still work for any board supporting the `periph_dac` feature.
### Issues/PRs references
19579: doc/doxygen/src/flashing.md: work around Doxygen bug r=maribu a=maribu
### Contribution description
Doxygen fails to render inline code in headers correctly in the version the CI uses. So, work around the issue by not typestetting `stm32flash` as inline code but as regular text.
19583: tests: move cpu related applications to tests/cpu r=maribu a=aabadie
19584: tests/build_system/external_board_dirs: fix broken symlinks r=maribu a=aabadie
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
