19970: sys/shell/gnrc_netif: fix ifconfig set language issue r=yarrick a=krzysztof-cabaj
### Contribution description
This PR fix some language issues in the output of `ifconfig set`.
### Testing procedure
Compile any program with `gnrc_netif` module, for example `examples/gcoap`.
Compare last line of presented outputs.
Output of `ifconfig help` without this PR.
```
All up, running the shell now
> ifconfig help
ifconfig help
usage: ifconfig help
usage: ifconfig <if_id> [up|down]
usage: ifconfig <if_id> set <key> <value>
Sets an hardware specific specific value
```
Output of `ifconfig help` with this PR.
```
All up, running the shell now
> ifconfig help
ifconfig help
usage: ifconfig
usage: ifconfig help
usage: ifconfig <if_id> [up|down]
usage: ifconfig <if_id> set <key> <value>
Sets a hardware specific value
```
### Issues/PRs references
None
Co-authored-by: krzysztof-cabaj <kcabaj@gmail.com>
Router Advertisements are enabled automatically for routing nodes
as soon as they obtain a prefix (e.g. via DHCPv6, UHCP, …).
Enabling router advertisements without a prefix to advertise is
wrong and causes no router solicitations to be send on an upstream
interface.
Also from https://www.rfc-editor.org/rfc/rfc4861#section-6.2.1
Note that AdvSendAdvertisements MUST be FALSE by
default so that a node will not accidentally start
acting as a router unless it is explicitly
configured by system management to send Router
Advertisements.
19825: drivers: rename st7735 to more generic st77xx r=aabadie a=gschorcht
### Contribution description
This PR provides the following changes:
- renames the driver `st7735` to `st77xx`
- renames the test `st7735` to `st77xx`
- models controller variants as pseudomodules `st7735`, `st7789` and `st7796`
- removes the buggy initialization as a workaround to use reset defaults, see issue #19818
- adds backward compatibility header files for `ST7735_PARAM_*` symbols
- adds a test board for compilation test of backward compatibility
- updates the corresponding board definitions
The PR should solve the remaining dependency issues in KConfig we had by using `st7735` module for different controller variants. The backward compatibility header files should work for boards that still use `ST7735_PARAM_*` in their board definitions so that the board defintions at user's side use shouldn't be affected.
~To be compilable, the PR includes PR #19824.~
### Testing procedure
- Green CI
- `tests/drivers/disp_dev` and `tests/drivers/st77xx` should still work for all boards using a ST77xx display.
- The PR was already tested for these tests for:
- [x] `adafruit-pybadge`
- [x] `esp32s2-lilygo-ttgo-t8`
- [x] `esp32s3-usb-otg`
- [x] `sipeed-longan-nano`
### Issues/PRs references
Workaround for issue #19818
Preqruisite for PR #19827
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19870: tests/gcoap_fileserver: only enable test with GCC r=benpicco a=benpicco
19900: gnrc_ipv6_nib: fix for border router with non-6lo interfaces r=benpicco a=benpicco
19902: tests/pkg/relic: skip CI testing with samr21-xpro and llvm toolchain r=benpicco a=aabadie
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Benjamin Valentin <benjamin.valentin@bht-berlin.de>
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
A border router should not send router advertisements on it's 6LoWPAN
interfaces, but if it also has classic IPv6 downstream interfaces it
should very much do so.
19881: drivers/stmpe811: fix initialization if callback function parameter is NULL r=benpicco a=gschorcht
### Contribution description
This PR fixes the `stmpe811` driver initialization if the callback function parameter `cb` is `NULL. This might be the case for example if the application uses the touch device in polling mode.
If the interrupt pin is initialized if the callback function parameter `cb` is `NULL`, the driver crashes the first time an interrupt is triggered. Therefore, the INT pin must be initialized only if also the callback function parameter `cb` is not `NULL`.
To be able to test the polling mode, this PR also includes a change of the `tests/drivers/stmpe811` application which introduces the environment variables `STMPE811_POLLING_MODE` `STMPE811_POLLING_PERIOD` and in the makefile.
### Testing procedure
1. Use a `stm32f429i-disc1` board and test it in polling mode:
```
STMPE811_POLLING_MODE=1 BOARD=stm32f429i-disc1 make -C tests/drivers/stmpe811 flash term
```
It should work as expected.
```
main(): This is RIOT! (Version: 2023.10-devel-119-g26e7a-drivers/stmpe811_fix_cb_null)
STMPE811 test application
+------------Initializing------------+
Initialization successful
Pressed!
X: 113, Y:135
X: 113, Y:135
X: 113, Y:136
Released!
```
2. Checkout master branch and cerry-pick commit 691a5e6308426ddc685e5a2c297238529211c258. The test application `tests/drivers/stmpe811` will crash once a touch event occur:
```
main(): This is RIOT! (Version: 2023.10-devel-117-g91441)
STMPE811 test application
+------------Initializing------------+
Initialization successful
Stack pointer corrupted, reset to top of stack
FSR/FAR:
CFSR: 0x00020000
HFSR: 0x40000000
DFSR: 0x00000008
AFSR: 0x00000000
Misc
EXC_RET: 0xfffffff1
*** RIOT kernel panic:
HARD FAULT HANDLER
```
### Issues/PRs references
19892: pkg/tinydtls: allow to set buffer size from application again r=benpicco a=leandrolanzieri
### Contribution description
Currently the buffer size on tinydtls is set in its Makefile whenever `gcoap` module is present. This limits the ability of the user to override the value. This adds a pre-check of the `CFLAGS` to see if it was set before.
### Testing procedure
Try setting `CFLAGS += -DDTLS_MAX_BUF=<some_value>` on `examples/gcoap_dtls`, you should be able to override the default value without errors.
### Issues/PRs references
Reported in #19838
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: Leandro Lanzieri <leandro.lanzieri@haw-hamburg.de>
19539: drivers/periph_sdmmc: define a High-level SDIO/SD/MMC API and low-level SDMMC periperal driver interface r=benpicco a=gschorcht
### Contribution description
This PR provides a SDIO/SD/MMC Device API (SDMMC). It implements a SD host controller driver that provides a high-level functions using a low-level SDIO/SD/MMC peripheral driver for accessing
- MultiMediaCards (MMC) and Embedded MultiMediaCards (eMMC)
- SD Memory Cards (SD Cards) with Standard Capacity (SDSC), High Capacity (SDHC) or Extended Capacity (SDXC).
It supports:
- 1-bit, 4-bit and 8-bit data bus width
- Default Speed and High Speed
- Auto-CLK
The SDIO/SD/MMC device API (SDMMC) is divided into two parts:
1. The high-level API that implements the SD Host Controller driver and allows
- to inititialize and identify different types of cards,
- to access them either blockwise or bytewise,
- to get information about the used card, and
- to send single commands or application specific commands to the card.
2. The low-level SDIO/SD/MMC peripheral driver implements the low-level functions required by the high-level device API. It has to be implemented for each MCU.
### Limitations:
- Only one card per SDIO/SD/MMC device is supported.
- eMMCs specific features are not supported.
- UHS-I, UHS-II and UHS-III are not supported.
### Testing procedure
PR #19540, PR #19760 or PR #19786 is needed to test this PR.
### Issues/PRs references
Prerequisite for PR #19540
Prerequisite for PR #19760
Prerequisite for PR #19786
19815: cpu/sam0_common/periph/sdhc: busy waiting and clock fixes r=benpicco a=benpicco
19860: drivers/ft5x06: fix vendor ID for FT6xx6 and FTxxxx register addresses r=benpicco a=gschorcht
### Contribution description
This PR provides a fix of the vendor ID for FT6xx6 touch panel driver ICs and a fix of register addresses for FTxxxx.
According to the [Application Note for FT6x06 CTPM](https://cdn-shop.adafruit.com/datasheets/FT6x06_AN_public_ver0.1.3.pdf), the vendor ID of FT6x06 touch panel driver ICs is `0x11` instead of `0xcd`. Although there are no information found in the Web about the FT6x36, the FT6336U touch panel of a ESP32-S3 WT32 SC01 Plus is also working with `0x11` as vendor ID so that it seems that FT6x36 is also using `0x11` as vendor ID.
Figured out with a `stm32f723e-disco` board (revision D03). Without this PR, `tests/drivers/ft5x06` gives:
```
+------------Initializing------------+
[ft5x06] init: invalid vendor ID: '0x11' (expected: 0xcd)
[Error] Initialization failed
```
With this PR it works as expected.
```
+------------Initializing------------+
Initialization successful
main(): This is RIOT! (Version: 2023.10-devel-96-gbb9011-drivers/ft5x06_fix_vendor_id)
FT5x06 test application
+------------Initializing------------+
[ft5x06] init: configuring touchscreen interrupt
Initialization successful
1 touch detected
[ft5x06] read gesture_id '0x00'
Touch 1 - X: 151, Y:138
[ft5x06] read gesture_id '0x00'
```
Some background information found in the Web:
- According to the [STM32CubeF7](c20e6dd15b/Drivers/BSP/STM32F723E-Discovery/stm32f723e_discovery_ts.c (L24-L27)) the FRIDA LCD panel mounted on the `stm32f723e-disco` board either uses FT6x36 (prior revision D) or FT3x67 (revision D). However, the FT5x06 driver type for the card is defined as FT6x06, which does not seem correct: bb9011c3fb/boards/stm32f723e-disco/include/board.h (L59)
- According to the [STM32CubeF7](c20e6dd15b/Drivers/BSP/Components/ft6x06/ft6x06.h (L269-L270)), the vendor ID for FT6x36 should be `0xcd`. However, the FT6336U on ESP32-S3 WT32 SC01 Plus works with vendor ID `0x11`.
- The [Adafruit FT6206 library](95118cd983/Adafruit_FT6206.h (L28)) uses `0x11` as vendor id.
- The `stm32l496g-disco` board uses a FT6236 which has vendor ID `0xcd`.
So the information available on the web is confusing. Maybe, a better solution would be to accept `0x11` as well as `0xcd` as vendor ID for FT6xxx touch panels. Unfortunately, there are no documents available on the registers directly from FocalTech 😟 so it seems to be more speculation than knowledge.
### Testing procedure
### Issues/PRs references
19886: cpu/efm32: fix DAC configuration r=benpicco a=gschorcht
### Contribution description
The EFM32 MCU allows the reference voltage to be configured per DAC device, not per DAC channel. Also, the DAC reference voltage was defined in the configuration but not used anywhere.
At the moment we have only defined one board (`stwstk6220a`) that uses the DAC, so changing the configuration interface shouldn't be critical.
### Testing procedure
`tests/periph/dac` should still work for the `stwstk6220a`
```
BOARD=slwstk6220a make -j8 -C tests/periph/dac flash
```
I don't have a `stwstk6220a` board (EFM32 Series 0) so that I can't test it. I could only test it for the `sltb009a` board (EFM32 Series 1) with the change for VDAC in PR #19887.
### Issues/PRs references
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
19876: sys/net/ipv4/addr: fix typos r=benpicco a=Enoch247
### Contribution description
This patch fixes some typos in the doxygen doc.
### Testing procedure
Nothing to test. No change to code.
### Issues/PRs references
- None known
19878: makefiles/usb_board_reset.mk: declare term-delay target with test target r=benpicco a=aabadie
19888: boards/sltb009a: complete and fix documentation r=benpicco a=gschorcht
### Contribution description
This PR completes and fixes the documentation which was still in the state as generated automatically by `efm2riot`.
The PR also includes a fix of the configuration of the second UART device that was find out while completing the documentation.
### Testing procedure
Green CI
### Issues/PRs references
Co-authored-by: Joshua DeWeese <jdeweese@primecontrols.com>
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19817: compile_and_test_for_boards: Add no-compile flag r=benpicco a=MrKevinWeiss
### Contribution description
Since we have a no-test flag that prevents executing tests, I think a no-compile flag is a nice compliment. Why? Well if I want to use this script for running multiple boards at the same time, RIOT is not so great handling parallel compile steps with conflicts on lockfiles happening, mostly due to packages. With this I can compile a list of boards sequentially, then flash and run tests in parallel, skipping the compile step.
### Testing procedure
Run the following once to compile and clean:
```
./dist/tools/compile_and_test_for_board/compile_and_test_for_board.py . native --applications tests/sys/shell --clean-after
```
Then try to run without the compile step and it should fail due to lack of the binary
```
./dist/tools/compile_and_test_for_board/compile_and_test_for_board.py . native --applications tests/sys/shell --no-compile
```
### Issues/PRs references
19826: ztimer/periodic: reinit remove from right clock and handle aquired ztimer r=benpicco a=kfessel
### Contribution description
#19806 added some retinit handling for ztimer periodic removing the timer from the new clock
This tries to detect if this is a reinit and remove the timer from the old clock
this also removes the ztimer_acquire/_release handling by removing now calls in favour of set return value and now values that are allready in ztimer,
that also has the potential to reduce the jitter of the periodic calls and bus-usage (for cpus that take their time to get "now")
### Testing procedure
read
run tests/sys/ztimer_periodic
### Issues/PRs references
Fixes#19806
19841: boards/adafruit-itsybitsy-nrf52: Add configuration for DotStar LED r=benpicco a=jimporter
19842: cpu/stm32: fix ld script for SRAM4 r=benpicco a=gschorcht
### Contribution description
This PR fixes the LD script for STM32.
Since the CCM and SRAM4 length are defined as symbols with perifx `_`, the LD script didn't use them correctly. Instead of using `ccmram_length` and `sram4_length`, `_ccmram_length` and `_sram4_length` have to be used. Furthermore, the location counter for the SRAM has to be set to the beginning of SRAM4 to work.
BTW, I don't understand why the `ccmram` region is defined. There is no section definition that would use it to place code or data with attribute `.ccmram.*` there.
Without the fix in this PR, defined symbols in `tests/sys/malloc` for the `b-u585i-iot02a` board were:
```python
00000000 T _sheap2 <== wrong start position because of wrong location counter
28000000 T _eheap2 <== wrong end position because of `sram4_length` is 0.
```
Although the `tests/sys/malloc` crashes for `b-u585i-iot02a` at the end of the heap (known problem, see [here](https://github.com/RIOT-OS/RIOT/pull/17410#issuecomment-996556823)), it uses only the backup RAM before it crashes:
```
Allocated 512 Bytes at 0x200bf600, total 756072
Allocated 512 Bytes at 0x200bf818, total 756592
Allocated 512 Bytes at 0x200bfa30, total 757112
Allocated 512 Bytes at 0x200bfc48, total 757632
Allocated 512 Bytes at 0x40036408, total 758152
Allocated 512 Bytes at 0x40036610, total 758672
Allocated 512 Bytes at 0x40036818, total 759192
```
With the fix in this PR, defined symbols in `tests/sys/malloc` for the `b-u585i-iot02a` board are:
```python
28000000 T _sheap2 <== correct start position
28004000 T _eheap2 <== correct end position
```
`tests/sys/malloc` also crashes for the `b-u585i-iot02a` at the end of the heap, but it uses also the SRAM4 before it crashes.
```
Allocated 512 Bytes at 0x200bf600, total 756072
Allocated 512 Bytes at 0x200bf818, total 756592
Allocated 512 Bytes at 0x200bfa30, total 757112
Allocated 512 Bytes at 0x200bfc48, total 757632
Allocated 512 Bytes at 0x40036408, total 758152
Allocated 512 Bytes at 0x40036610, total 758672
Allocated 512 Bytes at 0x40036818, total 759192
Allocated 512 Bytes at 0x28000008, total 759712
Allocated 512 Bytes at 0x28000210, total 760232
Allocated 512 Bytes at 0x28000418, total 760752
...
Allocated 512 Bytes at 0x280038e8, total 774272
Allocated 512 Bytes at 0x28003af0, total 774792
Allocated 512 Bytes at 0x28003cf8, total 775312
```
### Testing procedure
1. Flash `tests/sys/malloc` and use `MAX_MEM` limit to stop `malloc` before the crash:
```
CFLAGS='-DMAX_MEM=774800 -DCHUNK_SIZE=512 -DDEBUG_ASSERT_VERBOSE' \
BOARD=b-u585i-iot02a make -j8 -C tests/sys/malloc flash
```
Without the PR it crashes at the end of the backup RAM. With the PR it works.
2. Check `_sheap2` and `_eheap2` with
```
nm -s tests/sys/malloc/bin/b-u585i-iot02a/tests_malloc.elf | grep heap2 | sort
```
Without the PR it will be:
```
00000000 T _sheap2
28000000 T _eheap2
```
With the PR it should be:
```
28000000 T _sheap2
28004000 T _eheap2
```
### Issues/PRs references
Co-authored-by: MrKevinWeiss <weiss.kevin604@gmail.com>
Co-authored-by: Karl Fessel <karl.fessel@ovgu.de>
Co-authored-by: Jim Porter <jporterbugs@gmail.com>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
