When using `make flash` or `make term` with `MOST_RECENT_PORT=1`, RIOT
should now only consider plausible TTYs and select the most recently
connected one. The filter is a bit broad, though, and will match
any board with a CP2104 USB2UART bridge. But depending on the boards
attached, it might be good enough to reliably tell it apart from other
boards.
When using `make flash` or `make term` with `MOST_RECENT_PORT=1`, RIOT
should now only consider plausible TTYs and select the most recently
connected one. The filter is a bit broad, though, and will match
any board with a CP2102N USB2UART bridge. But depending on the boards
attached, it might be good enough to reliably tell it apart from other
boards.
When using `make flash` or `make term` with `MOST_RECENT_PORT=1`, RIOT
should now only consider plausible TTYs and select the most recently
connected one. The filter is a bit broad, though, and will match
any board with a CP2102 USB2UART bridge. But depending on the boards
attached, it might be good enough to reliably tell it apart from other
boards.
When using `make flash` or `make term` with `MOST_RECENT_PORT=1`, RIOT
should now select relatively robustly the most recently connected
ESP32 Ethernet Kit / ESP32 Wrover Kit board, even with other TTYs
present. This is because the FTDI Dual RS232-HS with two USB2UART
bridges in the chip would be an expensive overkill for most boards,
unless one is using the FTDI chip to big-bang JTAG as well - as done
on the Ethernet Kit and Wrover Kit boards.
The board have one user button and a user led but are not enabled.
This add necessary support to use the button and the led. It include
the configs to use with SAUL and button interrupt.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
- nRF51: Use `uart_conf_t` for consistency with nRF52
- nRF52832: Use UARTE (UART with EasyDMA) over UART (without DMA), as
done for all other nRF52 family members
- use `UARTE_PRESENT` to detect whether an UARTE can be used, rather
than family names
The `SWJ_CFG` field of the `AFIO_MAPR` register is write only and values
read are undefined (random). Hence, using `AFIO->MAPR |= mask;` to
enable flags can corrupt the state of the `SWJ_CFG` (configure it to
an unintended value).
Two helper functions have been introduced:
- `afio_mapr_read()` reads the value, but sanitizes the `SWJ_CFG` field
to zero
- `afio_mapr_write()` writes the given value, but applies the `SWJ_CFG`
configured by the board before writing.
Finally, the `nucleo-f103rb` and `bluepill*`/`blackpill*` boards have
been updated to no longer specify `STM32F1_DISABLE_JTAG`, as this
is handled by the `SWJ_CFG` setting (which defaults to disabling JTAG).
The macro `ARDUINO_SPI_D11D12D13` is used to refer to the SPI bus
on the pins D11/D12/D13 on Arduino UNO compatible boards. For all
Nucleo64 boards this is `SPI_DEV(0)`, but for this board `SPI_DEV(0)`
is internally connected to the radio. Instead `SPI_DEV(1)` is connected
to the correct pins. This provides the macro explicitly in
`periph_conf.h`, which takes preference over the fallback in
`boards/common/nucleo64` when provided.
20003: coap: create typedef for CoAP methods r=benpicco a=benpicco
20028: nanocoap: fix incorrect uses of coap_get_code() r=benpicco a=benpicco
20036: boards/nucleo-l4r5zi : add PWM configuration r=benpicco a=krzysztof-cabaj
### Contribution description
This PR adds to the Nucleo-l4r5zi PWM configuration
### Testing procedure
Flash the board using `tests/periph/pwm` program. Check if you could, for example, change LED
intensity using PWM.
### Issues/PRs references
None.
20041: pkg/littlefs2: bump to v2.8.1 r=benpicco a=bergzand
### Contribution description
Minor version number bump.
### Testing procedure
- Check if I copied the correct commit hash.
- Run the tests.
### Issues/PRs references
None
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: krzysztof-cabaj <kcabaj@gmail.com>
Co-authored-by: Koen Zandberg <koen@bergzand.net>
20032: boards/nucleo-l552ze: add PWM configuration r=benpicco a=krzysztof-cabaj
### Contribution description
This PR adds to the Nucleo-l552ze-q PWM configuration
### Testing procedure
Flash the board using `tests/periph/pwm` program. Check if you could, for example, change LED
intensity using PWM.
### Issues/PRs references
None.
Co-authored-by: krzysztof-cabaj <kcabaj@gmail.com>
19465: drivers/mtd: use XFA for pointers to defined MTDs r=benpicco a=gschorcht
### Contribution description
This PR provides the support to hold pointers to defined MTDs within a XFA. The XFA allows
- to access MTDs of different types (`mtd_flashpage`, `mtd_sdcard`, `mtd_emulated`, ...) by an index
- to determine the number of MTDs defined in the system.
### Testing procedure
To be defined once PR #19443 is merged because emulated MTDs will allow to test this PR on arbitrary boards.
### Porting Guide
For external boards:
- remove the `MTD_NUMOF` definition from `board.h`
- add `MTD_XFA_ADD(<mtd_dev>, <idx>);` to the definition of `<mtd_dev>`.
- `MTD_0`, `MTD_1`, … defines are no longer needed.
### Issues/PRs references
Related to PR #19443
19981: Fletcher32: Add incremental API r=benpicco a=bergzand
### Contribution description
This PR extends the current fletcher32 checksum with an incremental API mode. This way the bytes to be checksummed can be supplied via multiple successive calls and do not have to be provided in a single consecutive buffer.
I've also rephrased the warning with the original function a bit as that function uses an `unaligned_get_u16` to access the data. The data thus does not require alignment, but the length does need to be supplied as number of 16 bit words.
### Testing procedure
The test has been extended
### Issues/PRs references
None
19995: sys/psa_crypto: Fix macro for public key max size and SE example r=benpicco a=Einhornhool
### Contribution description
#### 1. Wrong public key size when using secure elements, introduced by #19954
Fixed conditions for key size macros in `crypto_sizes.h`.
#### 2. EdDSA and ECDSA examples fail when using a secure element because of unsopported changes introduced by #19954
Updated `example/psa_crypto` to use only supported functions for secure elements.
### Testing procedure
Build `example/psa_crypto` for secure elements and run application
Output on master:
```
2023-10-19 14:33:24,372 # main(): This is RIOT! (Version: 2019.07-devel-22378-gb6772)
2023-10-19 14:33:24,372 # HMAC SHA256 took 56393 us
2023-10-19 14:33:24,372 # Cipher AES 128 took 68826 us
2023-10-19 14:33:24,372 # *** RIOT kernel panic:
2023-10-19 14:33:24,373 # HARD FAULT HANDLER
2023-10-19 14:33:24,373 #
2023-10-19 14:33:24,373 # *** rebooting...
```
Output with fixes:
```
2023-10-19 13:35:24,715 # main(): This is RIOT! (Version: 2019.07-devel-22384-g8ef66-dev/psa-crypto-fixes)
2023-10-19 13:35:24,715 # HMAC SHA256 took 56374 us
2023-10-19 13:35:24,715 # Cipher AES 128 took 68805 us
2023-10-19 13:35:24,715 # ECDSA took 281164 us
2023-10-19 13:35:24,715 # All Done
```
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: Koen Zandberg <koen@bergzand.net>
Co-authored-by: Lena Boeckmann <lena.boeckmann@haw-hamburg.de>
19943: cpu/stm32: FMC used for low-level LCD parallel interface r=maribu a=gschorcht
### Contribution description
This PR provides the implementation of the LCD low-level MCU 8080 parallel interface using the FMC peripheral.
### Testing procedure
```
BOARD=stm32f723e-disco make -C tests/drivers/st77xx flash
```
and
```
BOARD=stm32l496g-disco make -C tests/drivers/st77xx flash
```
should work on top of PR #19941. Drawing operations should be much faster.
### Issues/PRs references
Depends on PR #19941
19978: treewide: fix typos to make codespell happy r=maribu a=maribu
### Contribution description
- fixes typos in comments and docs (no generated firmware changes expected)
- fixes a typo in a string in a GUI of a utility program
- add some false positives to the ignore list
### Testing procedure
- No generated binaries (except for the GUI version of the utility program to flash the MSB-A2) should change
- The diff should not look too scary
### Issues/PRs references
None
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@posteo.net>
Either the wiki is down, or the image was removed from upstream. This
replaces it with the same image hosted on the zephyr doc. As a site
effect, code spell likes the new URL much more.
