This commit fixes the clearing of a error condition after read.
This causes the incorrect errorcodes if the register is read
then an error occurs, then it is cleared.
By clearing only after the error is processed the bug is fixed.
This can be tested by reading a i2c slave that is not there.
There were still some things wrong with samd5x CPU init which only
showed up when used in conjunction with RIOTBOOT, that is cpu_init()
was called twice.
- gclk_connect() should block until the GCLK is ready.
- DPLL should be disabled dring configuration.
- make sure not to use DPLL for MCLK when re-configuring DPLL
- All APBxMASK bits should be in a defined state.
- always enable 1kHz oscilator output.
- Before, HSI was enabled as the default case when it is only
used for stm32f0 and stm32f1. It is now implemented explicitly
for those platforms, and only those.
- Since the Vector table must be naturally aligned to the next power
of two of the amount of supported ISR, and the table will be
placed after riotboot_hdr, we must ensure RIOTBOOT_HRD_LEN has the
same alignment.
This adds supoprt for the Atmel SAMD51 & SAME54 SoC.
The SAME5x/SAMD5x is a line of Cortex-M4F MCUs that share peripherals
with the samd2x Cortex-M0+ and saml1x Cortex-M23 parts.
Atmel Software Framework (ASF) provides a set of low-level header files
that give access to different hardware peripherals of Atmel's ICs.
Origin: Atmel SAMD51 Series Device Support (1.1.96)
License: Apache-2.0
URL: http://packs.download.atmel.com/Atmel.SAMD51_DFP.1.1.96.atpack
Atmel Software Framework (ASF) provides a set of low-level header
files that give access to different hardware peripherals of Atmel's
ICs.
Origin: Atmel SAME54 Series Device Support (1.0.87)
License: Apache-2.0
URL: http://packs.download.atmel.com/Atmel.SAME54_DFP.1.0.87.atpack
This cleans up the sam0 timer driver:
- remove the check for the unused freq parameter
- the MCU provides dedicated SET/CLR registers to avoid
read-modify-write, so don't do read-modify-write on them.
- workaround a possible hardware bug on SAMD5x:
loop until the CMD_READSYNC is really set
This change required correcting the values for LCRH_PEN and LRCH_EPS
values defined in cc26x0_uart.h, as they were incorrect according to
19.8.1.7 of the TI CC26x0 reference manual.
on-behalf-of: @sparkmeter <ben.postman@sparkmeter.io>
- _rom_start_addr, _ram_start_addr, _rom_length and _ran_length are
already defined in cortexm_common/Makefile.included and can therefore
be removed from kinetis/Makefile.include
- _ram_base_addr is never used and was not in commit history so
is also removed
- To be able to flash at an offset the vector table must be
relocated accordingly to the IMAGE_OFFSET, therefore linkage
needs to take the offset into account.
Rational: the periph_common module is required by (most) other periph drivers
and also during startup of the CPU/MCU to run periph_init. The latter is only
required if other periph drivers are used, hence periph_common should be a
depency of periph_* modules and *not* of the CPU/MCU. This PR fixes that
by making periph_common a depency of periph_* and removing the explicit
include in the CPU/MCU implementation.
Keep the compiled '.bin' file to remove the need to compile it when
flashing. This remove the need to have the toolchain when flashing so
allow compiling and flashing with `BUILD_IN_DOCKER=1` without a local
toolchain.
Even if it ends up storing a binary, the file is only 34 bytes.
Get OBJDUMP from the environment instead of hardwriting the value.
This is a prerequisite to allow using `objdump` when building from docker
when not having the `arm` toolchain installed.
