2018-07-26 11:48:55 +02:00
/**
@defgroup boards_nucleo-f030r8 STM32 Nucleo-F030R8
@ingroup boards_common_nucleo64
@brief Support for the STM32 Nucleo-F030R8
## Overview
2020-02-13 20:32:50 +01:00
The Nucleo-F030R8 is a board from ST's Nucleo family supporting a ARM Cortex-M0
2022-08-04 21:49:42 +02:00
STM32F030R8 microcontroller with 8KiB of RAM and 64KiB of Flash.
2018-07-26 11:48:55 +02:00
## Hardware
2023-09-27 09:10:15 +02:00
2018-07-26 11:48:55 +02:00
2023-03-17 15:04:17 +01:00
## Pinout
2018-07-26 11:48:55 +02:00
2024-10-12 17:42:40 +02:00
@image html pinouts/nucleo-f030r8.svg "Pinout for the Nucleo-F030R8 from STM user manual UM1724, http://www.st.com/resource/en/user_manual/dm00105823.pdf, page 28)" width=50%
2018-07-26 11:48:55 +02:00
### MCU
2020-06-04 11:26:06 +02:00
| MCU | STM32F030R8 |
|:---------- |:-------------------------------------------------------------------- |
| Family | ARM Cortex-M0 |
| Vendor | ST Microelectronics |
| RAM | 8KiB |
| Flash | 64KiB |
| Frequency | up to 48MHz |
| FPU | no |
| Timers | 10 (2x watchdog, 1 SysTick, 7x 16-bit) |
| ADCs | 1x 12-bit |
| UARTs | 2 |
| SPIs | 2 |
| I2Cs | 2 |
| RTC | 1 |
| Vcc | 2.4V - 3.6V |
2020-02-13 20:32:50 +01:00
| Datasheet | [Datasheet](http://www.st.com/resource/en/datasheet/stm32f030r8.pdf) |
| Reference Manual | [Reference Manual](https://www.st.com/resource/en/reference_manual/dm00091010.pdf) |
2018-07-26 11:48:55 +02:00
| Programming Manual | [Programming Manual](http://www.st.com/resource/en/programming_manual/dm00051352.pdf) |
| Board Manual | [Board Manual](http://www.st.com/resource/en/user_manual/dm00105823.pdf)|
## Implementation Status
| Device | ID | Supported | Comments |
|:------------- |:------------- |:------------- |:------------- |
| MCU | STM32F030R8 | partly | Energy saving modes not fully utilized |
| Low-level driver | GPIO | yes | |
| | PWM | yes (4 pins available) | |
| | UART | 2 UARTs | USART2 via STLink/USB or D0(RX)/D1(TX) and USART1 on PA10(RX)/PA09(TX) |
| | ADC | 6 pins | |
| | I2C | no | |
| | SPI | no | |
| | USB | no | |
| | Timer | 3 16 bit timers | |
## Flashing the device
2022-07-18 19:00:20 +02:00
### Flashing the Board Using OpenOCD
2020-02-13 20:32:50 +01:00
The ST Nucleo-F030R8 board includes an on-board ST-LINK V2 programmer. The
2018-07-26 11:48:55 +02:00
easiest way to program the board is to use OpenOCD. Once you have installed
OpenOCD (look [here](https://github.com/RIOT-OS/RIOT/wiki/OpenOCD) for
installation instructions), you can flash the board simply by typing
```
2020-02-13 20:32:50 +01:00
make BOARD=nucleo-f030r8 flash
2018-07-26 11:48:55 +02:00
```
and debug via GDB by simply typing
```
2020-02-13 20:32:50 +01:00
make BOARD=nucleo-f030r8 debug
2018-07-26 11:48:55 +02:00
```
2022-07-18 19:00:20 +02:00
### Flashing the Board Using ST-LINK Removable Media
On-board ST-LINK programmer provides via composite USB device removable media.
Copying the HEX file causes reprogramming of the board. This task
could be performed manually; however, the cpy2remed (copy to removable
media) PROGRAMMER script does this automatically. To program board in
this manner, use the command:
```
make BOARD=nucleo-f030r8 PROGRAMMER=cpy2remed flash
```
@note This PROGRAMMER was tested using ST-LINK firmware 2.37.26. Firmware updates
could be found on [this STM webpage](https://www.st.com/en/development-tools/stsw-link007.html).
2018-07-26 11:48:55 +02:00
## Supported Toolchains
2020-02-13 20:32:50 +01:00
For using the ST Nucleo-F030R8 board we strongly recommend the usage of the
2018-07-26 11:48:55 +02:00
[GNU Tools for ARM Embedded Processors](https://launchpad.net/gcc-arm-embedded)
toolchain.
*/
