mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2024-12-29 04:50:03 +01:00
73 lines
3.0 KiB
Plaintext
73 lines
3.0 KiB
Plaintext
|
/**
|
|||
|
|
@defgroup boards_mulle Eistec Mulle
|
|||
|
|
@ingroup boards
|
|||
|
|
@brief Support for Eistec Mulle IoT boards
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
The Mulle is a miniature wireless Embedded Internet System suitable for
|
|||
|
|
wireless sensors connected to the Internet of Things, and designed for rapid
|
|||
|
|
prototyping. It can be bought directly from [Eistec AB](http://www.eistec.se).
|
|||
|
|
|
|||
|
|
- [Official homepage](http://www.eistec.se/mulle)
|
|||
|
|
- [Eistec wiki](https://github.com/eistec/mulle/wiki)
|
|||
|
|
|
|||
|
|
Use `BOARD=mulle` for building RIOT for this platform.
|
|||
|
|
|
|||
|
|
## Components
|
|||
|
|
|
|||
|
|
https://github.com/eistec/mulle/wiki/Datasheets contains a list of relevant
|
|||
|
|
documentation for the components.
|
|||
|
|
|
|||
|
|
| MCU | MK60DN512VLL10 – Cortex-M4 |
|
|||
|
|
|-------|-----------------------------------|
|
|||
|
|
| RAM | 64kB |
|
|||
|
|
| Flash | 512kB|
|
|||
|
|
| radio chipset | AT86RF212B, sub-GHz IEEE802.15.4 transceiver, similar to the AT86RF233 |
|
|||
|
|
| external flash memory | Micron M25P16 16 Mbits external NOR flash, used for storing configuration, measurements and other slow changing non-volatile data |
|
|||
|
|
| external FRAM memory | Cypress/Ramtron FM25L04B 4 Kbits external F-RAM, used for storing counters and other rapidly changing non-volatile data |
|
|||
|
|
| accelerometer | ST micro LIS3DH MEMS accelerometer, |
|
|||
|
|
|
|||
|
|
|
|||
|
|
## Layout
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
## Implementation Status
|
|||
|
|
|
|||
|
|
The Mulle board is supported by mainline RIOT. See the below table for
|
|||
|
|
software support status for the different components.
|
|||
|
|
|
|||
|
|
| Device | ID | Supported | Comments |
|
|||
|
|
|:------------- |:------------- |:------------- |:------------- |
|
|||
|
|
| MCU | MK60DN512VLL10 | partly | See below |
|
|||
|
|
| Low-level driver | GPIO | yes | |
|
|||
|
|
| | PWM | yes | |
|
|||
|
|
| | UART | yes | |
|
|||
|
|
| | I2C | yes | |
|
|||
|
|
| | SPI | yes |Master mode works, slave mode unsupported |
|
|||
|
|
| | USB | no | [PR#3890](https://github.com/RIOT-OS/RIOT/pull/3890) |
|
|||
|
|
| | RTT | yes | |
|
|||
|
|
| | RNG | yes | |
|
|||
|
|
| | timer | yes | uses LPTMR module for TIMER_0 (used by xtimer), 32.768 kHz tick rate. PIT for additional timers, F_BUS tick rate (48 MHz default) |
|
|||
|
|
| | PM/LLWU | in progress | [PR#2605](https://github.com/RIOT-OS/RIOT/pull/2605) |
|
|||
|
|
| Radio Chip | AT86RF212B | yes | |
|
|||
|
|
| Accelerometer | LIS3DH | yes | |
|
|||
|
|
| Flash | M25P16 | in progress | [PR#6762](https://github.com/RIOT-OS/RIOT/pull/6762) |
|
|||
|
|
| FRAM | FM25L04B | yes | |
|
|||
|
|
|
|||
|
|
## Toolchains
|
|||
|
|
|
|||
|
|
See [ARM Family](https://github.com/RIOT-OS/RIOT/wiki/Family:-ARM), and
|
|||
|
|
[Eistec wiki - Installing-toolchain (GCC)](https://github.com/eistec/mulle/wiki/Installing-toolchain-%28GCC%29)
|
|||
|
|
|
|||
|
|
Working:
|
|||
|
|
* [gcc-arm-embedded](https://github.com/RIOT-OS/RIOT/wiki/Family:-ARM#gcc-arm-embedded-toolchain)
|
|||
|
|
* Clang 3.4 - Clang 4.0 - Install procedure not documented but pretty
|
|||
|
|
straightforward, Makefiles and build system is fully functional with Clang.
|
|||
|
|
|
|||
|
|
### Programming and Debugging
|
|||
|
|
|
|||
|
|
See [Eistec wiki](https://github.com/eistec/mulle/wiki).
|
|||
|
|
*/
|