mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2024-12-29 04:50:03 +01:00
84 lines
3.8 KiB
Plaintext
84 lines
3.8 KiB
Plaintext
/**
|
|
@defgroup boards_weact-f411ce WeAct-F411CE board
|
|
@ingroup boards
|
|
@brief Support for the WeAct-F411CE Board
|
|
|
|
## Overview
|
|
|
|
WeAct-F411CE is a board with the same form-factor as the blue/blackpill,
|
|
but with an STM32F411CEU6 and a USB-C connector.
|
|
|
|
It is available on sites like AliExpress for less than 4€.
|
|
|
|
## Hardware
|
|
|
|
|
|
|
|
### MCU
|
|
| MCU | STM32F411CEU6 |
|
|
|:---------------- |:--------------------- |
|
|
| Family | ARM Cortex-M4F |
|
|
| Vendor | ST Microelectronics |
|
|
| RAM | 128KiB |
|
|
| Flash | 512KiB |
|
|
| Frequency | up to 100MHz |
|
|
| FPU | yes |
|
|
| Timers | 8 (2x watchdog, 1 SysTick, 6x 16-bit) |
|
|
| ADCs | 1x 12-bit |
|
|
| UARTs | 3 |
|
|
| SPIs | 5 |
|
|
| I2Cs | 3 |
|
|
| RTC | 1 |
|
|
| Vcc | 2.0V - 3.6V |
|
|
| Datasheet | [Datasheet](https://www.st.com/resource/en/datasheet/stm32f411ce.pdf) |
|
|
| Reference Manual | [Reference Manual](https://www.st.com/content/ccc/resource/technical/document/reference_manual/9b/53/39/1c/f7/01/4a/79/DM00119316.pdf/files/DM00119316.pdf/jcr:content/translations/en.DM00119316.pdf) |
|
|
|
|
## Implementation Status
|
|
|
|
| Device | ID | Supported | Comments |
|
|
|:----------------- |:------------- |:------------------------- |:--------------------------------------------------------- |
|
|
| MCU | STM32F411CE | partly | Energy saving modes not fully utilized |
|
|
| Low-level driver | GPIO | yes | |
|
|
| | PWM | yes (4 pins available)) | |
|
|
| | UART | 2 UARTs | USART2 via PA3(RX)/PA2(TX), USART1 on PA10(RX)/PA9(TX) |
|
|
| | I2C | 1 I2C | |
|
|
| | SPI | 1 SPI | |
|
|
| | USB | yes | |
|
|
| | Timer | 1 32 bit timer (TIM5) | |
|
|
|
|
## Flashing the device
|
|
The device comes with a bootloader that allows flashing via `dfu-util`.
|
|
|
|
If RIOT is already running on the board, you can upload your RIOT-firmware by typing
|
|
|
|
```
|
|
make BOARD=weact-f411ce flash
|
|
```
|
|
|
|
RIOT will make sure to enter the bootloader automatically.
|
|
|
|
If RIOT crashed or you have the plain board with the stock firmware, you have to enter
|
|
the bootloader manually.
|
|
|
|
There are two buttons on the board labeled `BOOT0` and `NRST`.
|
|
|
|
- Hold down `BOOT0`
|
|
- Shortly press `NRST` to reset the CPU while keeping `BOOT0` held down
|
|
|
|
The board will now show up as `0483:df11` - `STM32 BOOTLOADER` and will accept
|
|
firmware using the DFU protocol.
|
|
|
|
*Note:* You need to have write permissions to the device.
|
|
On Linux you could add yourself to the `plugdev` group and store the following as `/etc/udev/rules.d/99-weact-f411ce.rules`:
|
|
|
|
```
|
|
SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="df11", GROUP="plugdev", MODE="660"
|
|
```
|
|
|
|
## UART
|
|
|
|
stdio is provided through USB CDC ACM so the board can be used
|
|
without any extra hardware, save for a USB-C cable.
|
|
|
|
*/
|