mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2024-12-29 04:50:03 +01:00
93 lines
3.4 KiB
Plaintext
93 lines
3.4 KiB
Plaintext
/**
|
|
@defgroup boards_nucleo-f410rb STM32 Nucleo-F410RB
|
|
@ingroup boards_common_nucleo64
|
|
@brief Support for the STM32 Nucleo-F410RB
|
|
|
|
## Overview
|
|
|
|
The Nucleo-F410RB is a board from ST's Nucleo family supporting a ARM Cortex-M4
|
|
STM32F410RB microcontroller with 32KiB of RAM and 128KiB of Flash.
|
|
|
|
## Hardware
|
|
|
|
|
|
|
|
## Pinout
|
|
|
|
@image html pinouts/nucleo-f410rb.svg "Pinout for the Nucleo-F410RB (from STM user manual UM1724, http://www.st.com/resource/en/user_manual/dm00105823.pdf, page 36)" width=50%
|
|
|
|
### MCU
|
|
|
|
| MCU | STM32F410RBT |
|
|
|:---------- |:----------------- |
|
|
| Family | ARM Cortex-M4 |
|
|
| Vendor | ST Microelectronics |
|
|
| RAM | 32KiB |
|
|
| Flash | 128KiB |
|
|
| Frequency | up to 100MHz |
|
|
| FPU | yes |
|
|
| Timers | 9 (2x watchdog, 1x SysTick, 4x 16-bit, 1x 32-bit [TIM2] and 1 low power timer) |
|
|
| ADCs | 1x 12-bit (16 channels) |
|
|
| UARTs | 3 |
|
|
| SPIs | 3 |
|
|
| I2Cs | 3 |
|
|
| RTC | 1 |
|
|
| Vcc | 1.8V - 3.6V |
|
|
| Datasheet | [Datasheet](http://www.st.com/resource/en/datasheet/stm32f410rb.pdf) |
|
|
| Reference Manual | [Reference Manual](http://www.st.com/resource/en/reference_manual/dm00180366.pdf) |
|
|
| Programming Manual | [Programming Manual](http://www.st.com/resource/en/programming_manual/dm00046982.pdf) |
|
|
| Board Manual | [Board Manual](http://www.st.com/resource/en/user_manual/dm00105823.pdf)|
|
|
|
|
## Implementation Status
|
|
|
|
| Device | ID | Supported | Comments |
|
|
|:------------- |:------------- |:------------- |:------------- |
|
|
| MCU | STM32F410RB | partly | Energy saving modes not fully utilized |
|
|
| Low-level driver | GPIO | yes | |
|
|
| | PWM | yes (no pin configured) | |
|
|
| | UART | 2 UARTs | USART2 via STLink/USB or D0(RX)/D1(TX) and USART1 on PA10(RX)/PA9(TX) |
|
|
| | I2C | 1 I2C | |
|
|
| | SPI | 1 SPI | |
|
|
| | USB | no | |
|
|
| | Timer | 2 32 bit timers | |
|
|
|
|
## Flashing the device
|
|
|
|
### Flashing the Board Using OpenOCD
|
|
|
|
The ST Nucleo-F410RB board includes an on-board ST-LINK V2 programmer. The
|
|
easiest way to program the board is to use OpenOCD. You need OpenOCD in
|
|
version
|
|
0.10 minimum. Once you have installed OpenOCD (look
|
|
[here](https://github.com/RIOT-OS/RIOT/wiki/OpenOCD) for installation
|
|
instructions), you can flash the board simply by typing
|
|
|
|
```
|
|
make BOARD=nucleo-f410rb flash
|
|
```
|
|
and debug via GDB by simply typing
|
|
```
|
|
make BOARD=nucleo-f410rb debug
|
|
```
|
|
|
|
### Flashing the Board Using ST-LINK Removable Media
|
|
|
|
On-board ST-LINK programmer provides via composite USB device removable media.
|
|
Copying the HEX file causes reprogramming of the board. This task
|
|
could be performed manually; however, the cpy2remed (copy to removable
|
|
media) PROGRAMMER script does this automatically. To program board in
|
|
this manner, use the command:
|
|
```
|
|
make BOARD=nucleo-f410rb PROGRAMMER=cpy2remed flash
|
|
```
|
|
@note This PROGRAMMER was tested using ST-LINK firmware 2.37.26. Firmware updates
|
|
could be found on [this STM webpage](https://www.st.com/en/development-tools/stsw-link007.html).
|
|
|
|
|
|
## Supported Toolchains
|
|
|
|
For using the ST Nucleo-F410RB board we strongly recommend the usage of the
|
|
[GNU Tools for ARM Embedded Processors](https://launchpad.net/gcc-arm-embedded)
|
|
toolchain.
|
|
*/
|