mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2024-12-29 04:50:03 +01:00
52 lines
2.0 KiB
Plaintext
52 lines
2.0 KiB
Plaintext
/**
|
|
@defgroup boards_nucleo-l476rg STM32 Nucleo-L476RG
|
|
@ingroup boards_common_nucleo64
|
|
@brief Support for the STM32 Nucleo-L476RG
|
|
|
|
### MCU
|
|
|
|
|
|
| MCU | STM32L476RG |
|
|
|:------------- |:--------------------- |
|
|
| Family | ARM Cortex-M4 |
|
|
| Vendor | ST Microelectronics |
|
|
| RAM | 128Kb |
|
|
| Flash | 1MB |
|
|
| Frequency | up to 80MHz |
|
|
| FPU | yes |
|
|
| Timers | 16 (2x watchdog, 1 SysTick, 6x 16-bit, 2x 32-bit [TIM2]) |
|
|
| ADCs | 1x 12-bit |
|
|
| UARTs | 3 (two UARTs and one Low-Power UART) |
|
|
| SPIs | 3 |
|
|
| I2Cs | 3 |
|
|
| RTC | 1 |
|
|
| CAN | 1 |
|
|
| Vcc | 1.71 V - 3.6V |
|
|
| Datasheet | |
|
|
| Reference Manual | [Reference Manual](http://www.st.com/content/ccc/resource/technical/document/reference_manual/02/35/09/0c/4f/f7/40/03/DM00083560.pdf/files/DM00083560.pdf/jcr:content/translations/en.DM00083560.pdf) |
|
|
| Programming Manual | [Programming Manual](http://www.st.com/content/ccc/resource/technical/document/programming_manual/6c/3a/cb/e7/e4/ea/44/9b/DM00046982.pdf/files/DM00046982.pdf/jcr:content/translations/en.DM00046982.pdf) |
|
|
| Board Manual | [Board Manual](https://www.st.com/content/ccc/resource/technical/document/user_manual/98/2e/fa/4b/e0/82/43/b7/DM00105823.pdf/files/DM00105823.pdf/jcr:content/translations/en.DM00105823.pdf) |
|
|
|
|
## Flashing the device
|
|
|
|
The ST Nucleo-L476RG board includes an on-board ST-LINK V2 programmer. The
|
|
easiest way to program the board is to use OpenOCD. Once you have installed
|
|
OpenOCD (look [here](https://github.com/RIOT-OS/RIOT/wiki/OpenOCD) for
|
|
installation instructions), you can flash the board simply by typing
|
|
|
|
```
|
|
make BOARD=nucleo-l476rg flash
|
|
```
|
|
and debug via GDB by simply typing
|
|
```
|
|
make BOARD=nucleo-l476rg debug
|
|
```
|
|
|
|
|
|
## Supported Toolchains
|
|
|
|
For using the ST Nucleo-L476RG board we strongly recommend the usage of the
|
|
[GNU Tools for ARM Embedded Processors](https://launchpad.net/gcc-arm-embedded)
|
|
toolchain.
|
|
*/
|