mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2024-12-29 04:50:03 +01:00
74 lines
4.6 KiB
Plaintext
74 lines
4.6 KiB
Plaintext
/**
|
||
@defgroup boards_mulle Eistec Mulle
|
||
@ingroup boards
|
||
@brief Support for Eistec Mulle IoT boards
|
||
|
||
|
||
|
||
The Mulle is a miniature wireless Embedded Internet System suitable for
|
||
wireless sensors connected to the Internet of Things, and designed for rapid
|
||
prototyping.
|
||
|
||
- [Official homepage (Archived)]
|
||
(https://web.archive.org/web/20161213064400/http://www.eistec.se/mulle)
|
||
- [Eistec wiki](https://github.com/eistec/mulle/wiki)
|
||
|
||
Use `BOARD=mulle` for building RIOT for this platform.
|
||
|
||
## Components
|
||
|
||
https://github.com/eistec/mulle/wiki/Datasheets contains a list of relevant
|
||
documentation for the components.
|
||
|
||
| MCU | MK60DN512VLL10 – Cortex-M4 |
|
||
|:--------------------- |:--------------------------------------------------------------------------------------------------------------------------------- |
|
||
| RAM | 64KiB |
|
||
| Flash | 512KiB |
|
||
| radio chipset | AT86RF212B, sub-GHz IEEE802.15.4 transceiver, similar to the AT86RF233 |
|
||
| external flash memory | Micron M25P16 2 MiB external NOR flash, used for storing configuration, measurements and other slow changing non-volatile data |
|
||
| external FRAM memory | Cypress/Ramtron FM25L04B 512B external F-RAM, used for storing counters and other rapidly changing non-volatile data |
|
||
| accelerometer | ST micro LIS3DH MEMS accelerometer |
|
||
|
||
|
||
## Layout
|
||
|
||
|
||
|
||
## Implementation Status
|
||
|
||
The Mulle board is supported by mainline RIOT. See the below table for
|
||
software support status for the different components.
|
||
|
||
| Device | ID | Supported | Comments |
|
||
|:----------------- |:----------------- |:------------- |:----------------------------------------------------- |
|
||
| MCU | MK60DN512VLL10 | partly | See below |
|
||
| Low-level driver | GPIO | yes | |
|
||
| | PWM | yes | |
|
||
| | UART | yes | |
|
||
| | I2C | yes | |
|
||
| | SPI | yes | Slave mode unsupported |
|
||
| | USB | no | [PR#3890](https://github.com/RIOT-OS/RIOT/pull/3890) |
|
||
| | RTT | yes | |
|
||
| | RNG | yes | |
|
||
| | timer | yes | uses LPTMR module for TIMER_0 (used by xtimer), 32.768 kHz tick rate. PIT for additional timers, F_BUS tick rate (48 MHz default) |
|
||
| | PM/LLWU | in progress | [PR#2605](https://github.com/RIOT-OS/RIOT/pull/2605) |
|
||
| Radio Chip | AT86RF212B | yes | |
|
||
| Accelerometer | LIS3DH | yes | |
|
||
| Flash | M25P16 | yes | |
|
||
| FRAM | FM25L04B | yes | |
|
||
|
||
## Toolchains
|
||
|
||
See [ARM Family](https://github.com/RIOT-OS/RIOT/wiki/Family:-ARM), and
|
||
[Eistec wiki - Installing-toolchain (GCC)](https://github.com/eistec/mulle/wiki/Installing-toolchain-%28GCC%29)
|
||
|
||
Working:
|
||
* [gcc-arm-embedded](https://github.com/RIOT-OS/RIOT/wiki/Family:-ARM#gcc-arm-embedded-toolchain)
|
||
* Clang 3.4 - Clang 4.0 - Install procedure not documented but pretty
|
||
straightforward, Makefiles and build system is fully functional with Clang.
|
||
|
||
### Programming and Debugging
|
||
|
||
See [Eistec wiki](https://github.com/eistec/mulle/wiki).
|
||
*/
|