mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2024-12-29 04:50:03 +01:00
227 lines
12 KiB
Plaintext
227 lines
12 KiB
Plaintext
/**
|
|
* @defgroup boards_ikea-tradfri IKEA TRÅDFRI modules
|
|
* @ingroup boards
|
|
* @brief Support for the IKEA TRÅDFRI modules
|
|
|
|
## Overview
|
|
The IKEA TRÅDFRI is a small board found in different IKEA TRÅDFRI products.
|
|
The board contains an EFR32 microcontroller and a 2MBit SPI NOR Flash.
|
|
|
|
More information about the module can be found on this
|
|
[GitHub page](https://github.com/basilfx/TRADFRI-Hacking).
|
|
|
|
## Hardware
|
|
|
|
##
|
|
| MCU | EFR32MG1P132F256GM32 |
|
|
|-----------------|-----------------------------------------------------------------------------------------|
|
|
| Family | ARM Cortex-M4F |
|
|
| Vendor | Silicon Labs |
|
|
| Vendor Family | EFR32 Mighty Gecko 1P |
|
|
| RAM | 32.0 KiB (1.0 KiB reserved) |
|
|
| Flash | 256.0 KiB |
|
|
| EEPROM | no |
|
|
| Frequency | up to 38.4 MHz |
|
|
| FPU | yes |
|
|
| MPU | yes |
|
|
| DMA | 12 channels |
|
|
| Timers | 2x 16-bit + 1x 16-bit (low power) |
|
|
| ADCs | 12-bit ADC |
|
|
| UARTs | 2x USART, 1x LEUART |
|
|
| SPIs | 2x USART |
|
|
| I2Cs | 1x |
|
|
| Vcc | 1.85 V - 3.8 V |
|
|
| Datasheet | [Datasheet](https://www.silabs.com/documents/public/data-sheets/efr32mg1-datasheet.pdf) |
|
|
| Manual | [Manual](https://www.silabs.com/documents/public/reference-manuals/efr32xg1-rm.pdf) |
|
|
|
|
### Module versions
|
|
There are currently two types of modules available. The older module is labeled
|
|
ICC-1 and the newer one ICC-A-1. The main difference, is that pin PF3 is now
|
|
used to enable the SPI NOR Flash, and not exposed anymore.
|
|
|
|
### Pinout
|
|
Pin 1 is on the top-left side with only 6 contacts.
|
|
|
|
| | PIN | PIN | |
|
|
|------|-----|-----|------|
|
|
| | | 16 | RES |
|
|
| | | 15 | PF3 |
|
|
| PA0 | 1 | 14 | PF2 |
|
|
| PA1 | 2 | 13 | PF1 |
|
|
| PB12 | 3 | 12 | PF0 |
|
|
| PB13 | 4 | 11 | PC11 |
|
|
| GND | 5 | 10 | PC10 |
|
|
| 3V3 | 6 | 9 | PB14 |
|
|
| | | 8 | PB15 |
|
|
| | | 7 | GND |
|
|
|
|
**Note**: On the ICC-A-1 module, PF3 is not exposed anymore.
|
|
|
|
### Peripheral mapping
|
|
| Peripheral | Number | Hardware | Pins | Comments |
|
|
|------------|---------|-----------------|-----------------------------------|-----------------------------------------------------|
|
|
| ADC | 0 | ADC0 | CHAN0: internal temperature | Ports are fixed, 14/16-bit resolution not supported |
|
|
| HWCRYPTO | — | — | | AES128/AES256, SHA1, SHA256 |
|
|
| RTT | — | RTCC | | 1 Hz interval. Either RTT or RTC (see below) |
|
|
| RTC | — | RTCC | | 1 Hz interval. Either RTC or RTT (see below) |
|
|
| SPI | 0 | USART1 | MOSI: PD15, MISO: PD14, CLK: PD13 | |
|
|
| Timer | 0 | TIMER0 + TIMER1 | | TIMER0 is used as prescaler (must be adjacent) |
|
|
| | 1 | LETIMER0 | | |
|
|
| UART | 0 | USART0 | RX: PB15, TX: PB14 | Default STDIO output |
|
|
| | 1 | LEUART0 | RX: PB15, TX: PB14 | Baud rate limited (see below) |
|
|
|
|
### User interface
|
|
| Peripheral | Mapped to | Pin | Comments |
|
|
|------------|-----------|------|----------|
|
|
| LED | LED0 | PB13 | |
|
|
| | LED1 | PA1 | |
|
|
|
|
## Implementation Status
|
|
| Device | ID | Supported | Comments |
|
|
|------------------|------------|-----------|----------------------------------------------------------------|
|
|
| MCU | EFR32MG1P | yes | Power modes supported |
|
|
| Low-level driver | ADC | yes | |
|
|
| | Flash | yes | |
|
|
| | GPIO | yes | Interrupts are shared across pins (see reference manual) |
|
|
| | HW Crypto | yes | |
|
|
| | I2C | yes | |
|
|
| | PWM | yes | |
|
|
| | RTCC | yes | As RTT or RTC |
|
|
| | SPI | partially | Only master mode |
|
|
| | Timer | yes | |
|
|
| | UART | yes | USART is shared with SPI. LEUART baud rate limited (see below) |
|
|
| SPI NOR Flash | IS25LQ020B | yes | 2MBit flash. Can be used with the the MTD API. |
|
|
|
|
## Board configuration
|
|
|
|
### UART selection
|
|
By default the UART peripheral is used for the TX/RX pins, however the pinout
|
|
is compatible with LEUART also. You can switch from UART to LEUART by compiling
|
|
with `EFM32_USE_LEUART=1`.
|
|
|
|
**Note**: LEUART is not working on the ICC-1 module.
|
|
|
|
### Clock selection
|
|
There are several clock sources that are available for the different
|
|
peripherals. You are advised to read
|
|
[AN0004.1](https://www.silabs.com/documents/public/application-notes/an0004.1-efm32-cmu.pdf)
|
|
to get familiar with the different clocks.
|
|
|
|
| Source | Internal | Speed | Comments |
|
|
|--------|----------|------------|------------------------------------|
|
|
| HFRCO | Yes | 19 MHz | Enabled during startup, changeable |
|
|
| HFXO | No | 38.4 MHz | |
|
|
| LFRCO | Yes | 32.768 kHz | |
|
|
| ULFRCO | No | 1 kHz | Not very reliable as a time source |
|
|
|
|
The sources can be used to clock following branches:
|
|
|
|
| Branch | Sources | Comments |
|
|
|--------|-------------------------|------------------------------|
|
|
| HF | HFRCO, HFXO | Core, peripherals |
|
|
| LFA | LFRCO, LFXO | Low-power timers |
|
|
| LFB | LFRCO, LFXO, CORELEDIV2 | Low-power UART |
|
|
| LFE | LFRCO, LFXO | Real-time Clock and Calendar |
|
|
|
|
CORELEDIV2 is a source that depends on the clock source that powers the core.
|
|
It is divided by 2 or 4 to not exceed maximum clock frequencies (EMLIB takes
|
|
care of this).
|
|
|
|
The frequencies mentioned in the tables above are specific for this starter
|
|
kit.
|
|
|
|
It is important that the clock speeds are known to the code, for proper
|
|
calculations of speeds and baud rates. If the HFXO or LFXO are different from
|
|
the speeds above, ensure to pass `EFM32_HFXO_FREQ=freq_in_hz` and
|
|
`EFM32_LFXO_FREQ=freq_in_hz` to your compiler.
|
|
|
|
You can override the branch's clock source by adding `CLOCK_LFA=source` to
|
|
your compiler defines, e.g. `CLOCK_LFA=cmuSelect_LFRCO`.
|
|
|
|
### Low-power peripherals
|
|
The low-power UART is capable of providing an UART peripheral using a low-speed
|
|
clock. When the LFB clock source is the LFRCO or LFXO, it can still be used in
|
|
EM2. However, this limits the baud rate to 9600 baud. If a higher baud rate is
|
|
desired, set the clock source to CORELEDIV2.
|
|
|
|
**Note:** peripheral mappings in your board definitions will not be affected by
|
|
this setting. Ensure you do not refer to any low-power peripherals.
|
|
|
|
### RTC or RTT
|
|
RIOT-OS has support for *Real-Time Tickers* and *Real-Time Clocks*.
|
|
|
|
However, this board MCU family has support for a 32-bit *Real-Time Clock and
|
|
Calendar*, which can be configured in ticker mode **or** calendar mode.
|
|
Therefore, only one of both peripherals can be enabled at the same time.
|
|
|
|
Configured at 1 Hz interval, the RTCC will overflow each 136 years.
|
|
|
|
### Hardware crypto
|
|
This MCU is equipped with a hardware-accelerated crypto peripheral that can
|
|
speed up AES128, AES256, SHA1, SHA256 and several other cryptographic
|
|
computations.
|
|
|
|
A peripheral driver interface is proposed, but not yet implemented.
|
|
|
|
### Usage of EMLIB
|
|
This port makes uses of EMLIB by Silicon Labs to abstract peripheral registers.
|
|
While some overhead is to be expected, it ensures proper setup of devices,
|
|
provides chip errata and simplifies development. The exact overhead depends on
|
|
the application and peripheral usage, but the largest overhead is expected
|
|
during peripheral setup. A lot of read/write/get/set methods are implemented as
|
|
inline methods or macros (which have no overhead).
|
|
|
|
Another advantage of EMLIB are the included assertions. These assertions ensure
|
|
that peripherals are used properly. To enable this, pass `DEBUG_EFM` to your
|
|
compiler.
|
|
|
|
### Pin locations
|
|
The EFM32 platform supports peripherals to be mapped to different pins
|
|
(predefined locations). The definitions in `periph_conf.h` mostly consist of a
|
|
location number and the actual pins. The actual pins are required to configure
|
|
the pins via GPIO driver, while the location is used to map the peripheral to
|
|
these pins.
|
|
|
|
In other words, these definitions must match. Refer to the data sheet for more
|
|
information.
|
|
|
|
This MCU has extended pin mapping support. Each pin of a peripheral can be
|
|
connected separately to one of the predefined pins for that peripheral.
|
|
|
|
## Flashing the device
|
|
To flash, [SEGGER JLink](https://www.segger.com/jlink-software.html) is
|
|
required.
|
|
|
|
Flashing is supported by RIOT-OS using the command below:
|
|
|
|
```
|
|
make flash
|
|
```
|
|
|
|
To run the GDB debugger, use the command:
|
|
|
|
```
|
|
make debug
|
|
```
|
|
|
|
Or, to connect with your own debugger:
|
|
|
|
```
|
|
make debug-server
|
|
```
|
|
|
|
Some boards have (limited) support for emulation, which can be started with:
|
|
|
|
```
|
|
make emulate
|
|
```
|
|
|
|
## Supported Toolchains
|
|
For using the Silicon Labs STK3600 starter kit we strongly recommend
|
|
the usage of the [GNU Tools for ARM Embedded Processors](https://developer.arm.com/open-source/gnu-toolchain/gnu-rm)
|
|
toolchain.
|
|
|
|
## License information
|
|
* Silicon Labs' EMLIB: zlib-style license (permits distribution of source).
|
|
*/
|