mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2024-12-29 04:50:03 +01:00
67 lines
2.8 KiB
Plaintext
67 lines
2.8 KiB
Plaintext
/**
|
|
@defgroup boards_atxmega-a1u-xpro ATxmega-A1U Xplained Pro board
|
|
@ingroup boards
|
|
@brief Support for the ATxmega-A1U Xplained Pro board
|
|
|
|
## Overview
|
|
|
|
The ATxmega-A1U Xplained Pro is the reference to develop with XMEGA's.
|
|
|
|
### MCU
|
|
| MCU | ATxmega128A1U |
|
|
|:------------- |:--------------------------------------------- |
|
|
| Family | AVR/ATxmega |
|
|
| Vendor | Microchip (previously Atmel) |
|
|
| Flash | 128KiB |
|
|
| RAM | 8KiB |
|
|
| EBI | 16MiB SRAM, 128MiB SDRAM |
|
|
| EEPROM | 2KiB |
|
|
| Frequency | up to 32MHz |
|
|
| Timers | 8 16bit (32 bit combining 2 x 16 bit) |
|
|
| ACs | 4 Analog Comparators |
|
|
| ADCs | 2 - 16 channels - 12 bit - 2msps |
|
|
| ADCs | 2 - 2 channels - 12 bit - 1msps |
|
|
| UARTs | 8 (can be used in SPI mode) with 1 IrDA |
|
|
| SPIs | 4 |
|
|
| I2Cs | 4 (called TWI) |
|
|
| USB | 1 port |
|
|
| DMA | 4 Channels |
|
|
| Event System | 8 Channels |
|
|
| Ext. INT | All GPIOs |
|
|
| Crypto | AES/DES, CRC-16, CRC-32 |
|
|
| Vcc | 1.6V - 3.6V |
|
|
| Datasheet | [Datasheet](https://ww1.microchip.com/downloads/en/DeviceDoc/ATxmega128A1U-64A1U-Data-Sheet-DS40002058A.pdf) |
|
|
| Xmega Manual | [Manual](https://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-8331-8-and-16-bit-AVR-Microcontroller-XMEGA-AU_Manual.pdf) |
|
|
| Guide | [User Guide](https://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-42211-XMEGA-A1U-Xplained-Pro_User-Guide.pdf) |
|
|
| Design Files | [Files](https://ww1.microchip.com/downloads/en/DeviceDoc/XMEGA-A1U-Xplained-Pro_Design-Documentation.zip) |
|
|
|
|
## Flashing the Device
|
|
|
|
The ATxmega-A1U Xplained Pro came with a full EDBG + CDC-ACM. The EDBG works
|
|
with default avrdude tool. However, the below programmer must have at
|
|
/etc/avrdude.conf file:
|
|
|
|
programmer
|
|
id = "xplainedpro_pdi";
|
|
desc = "Atmel AVR XplainedPro in PDI mode";
|
|
type = "jtagice3_pdi";
|
|
connection_type = usb;
|
|
usbpid = 0x2111;
|
|
;
|
|
|
|
In order to flash the ATxmega128A1U, simple run:
|
|
|
|
make BOARD=atxmega-a1u-xpro flash
|
|
|
|
## Serial Terminal
|
|
|
|
The CDC-ACM will enumerate a /dev/ttyACM device.
|
|
|
|
make BOARD=atxmega-a1u-xpro term
|
|
|
|
## On-Chip Debugging (OCD)
|
|
|
|
make debug
|
|
|
|
*/
|