mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2024-12-29 04:50:03 +01:00
56 lines
2.5 KiB
Plaintext
56 lines
2.5 KiB
Plaintext
/**
|
|
@defgroup boards_nucleo-l433rc STM32 Nucleo-L433RC
|
|
@ingroup boards_common_nucleo64
|
|
@brief Support for the STM32 Nucleo-L433RC
|
|
|
|
## Overview
|
|
|
|
The Nucleo-L433RC is a board from ST's Nucleo family supporting a ARM
|
|
Cortex-M4 STM32L433RC microcontroller with 64KiB of RAM and 256KiB of Flash.
|
|
|
|
### Hardware
|
|
|
|
|
|
|
|
### Pinout
|
|
|
|
@image html pinouts/nucleo-l433rc.svg "Pinout for the Nucleo-L433RC (from STM user manual, UM2206, http://www.st.com/resource/en/user_manual/um2206-stm32-nucleo64p-boards-mb1319-stmicroelectronics.pdf, page 37)" width=50%
|
|
|
|
### MCU
|
|
|
|
| MCU | STM32L476RG |
|
|
|:---------- |:------------------- |
|
|
| Family | ARM Cortex-M4 |
|
|
| Vendor | ST Microelectronics |
|
|
| RAM | 64KiB |
|
|
| Flash | 256KiB |
|
|
| Frequency | up to 80MHz |
|
|
| FPU | yes |
|
|
| Timers | 11 (2x watchdog, 1 SysTick, 7x 16-bit, 1x 32-bit) |
|
|
| ADCs | 1x 12-bit |
|
|
| UARTs | 5 (four USARTs and one Low-Power UART) |
|
|
| SPIs | 3 |
|
|
| I2Cs | 3 |
|
|
| RTC | 1 |
|
|
| CAN | 1 |
|
|
| Vcc | 1.71 V - 3.6V |
|
|
| Datasheet | [Datasheet](https://www.st.com/resource/en/datasheet/stm32l433rc.pdf) |
|
|
| Reference Manual | [Reference Manual](https://www.st.com/resource/en/reference_manual/rm0394-stm32l41xxx42xxx43xxx44xxx45xxx46xxx-advanced-armbased-32bit-mcus-stmicroelectronics.pdf) |
|
|
| Programming Manual | [Programming Manual](http://www.st.com/content/ccc/resource/technical/document/programming_manual/6c/3a/cb/e7/e4/ea/44/9b/DM00046982.pdf/files/DM00046982.pdf/jcr:content/translations/en.DM00046982.pdf) |
|
|
| Board Manual | [Board Manual](http://www.st.com/resource/en/user_manual/um2206-stm32-nucleo64p-boards-mb1319-stmicroelectronics.pdf) |
|
|
|
|
### Flashing the Board Using ST-LINK Removable Media
|
|
|
|
On-board ST-LINK programmer provides via composite USB device removable media.
|
|
Copying the HEX file causes reprogramming of the board. This task
|
|
could be performed manually; however, the cpy2remed (copy to removable
|
|
media) PROGRAMMER script does this automatically. To program board in
|
|
this manner, use the command:
|
|
```
|
|
make BOARD=nucleo-l433rc PROGRAMMER=cpy2remed flash
|
|
```
|
|
@note This PROGRAMMER was tested using ST-LINK firmware 2.37.26. Firmware updates
|
|
could be found on [this STM webpage](https://www.st.com/en/development-tools/stsw-link007.html).
|
|
|
|
*/
|