mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2024-12-29 04:50:03 +01:00
93 lines
3.5 KiB
Plaintext
93 lines
3.5 KiB
Plaintext
/**
|
|
@defgroup boards_nucleo-f207zg STM32 Nucleo-F207ZG
|
|
@ingroup boards_common_nucleo144
|
|
@brief Support for the STM32 Nucleo-F207ZG
|
|
|
|
## Overview
|
|
|
|
The Nucleo-F207ZG is a board from ST's Nucleo family supporting a ARM
|
|
Cortex-M3
|
|
STM32F207ZG microcontroller with 128KiB of SRAM and 1MiB of ROM Flash.
|
|
|
|
## Hardware
|
|
|
|
|
|
|
|
## Pinout
|
|
|
|
@image html pinouts/nucleo-f207zg-and-more.svg "Pinout for the Nucleo-F207ZG (from STM user manual, UM1974, http://www.st.com/resource/en/user_manual/dm00244518.pdf, page 32)" width=50%
|
|
|
|
### MCU
|
|
|
|
| MCU | STM32F207ZG |
|
|
|:---------- |:----------------- |
|
|
| Family | ARM Cortex-M3 |
|
|
| Vendor | ST Microelectronics |
|
|
| RAM | 128KiB |
|
|
| Flash | 1MiB |
|
|
| Frequency | up to 120MHz |
|
|
| FPU | no |
|
|
| Timers | 17 (2x watchdog, 1 SysTick, 12x 16-bit, 2x 32-bit [TIM2]) |
|
|
| ADCs | 3x 12-bit (24 channels) |
|
|
| UARTs | 6 |
|
|
| SPIs | 3 |
|
|
| I2Cs | 3 |
|
|
| RTC | 1 |
|
|
| CAN | 2 |
|
|
| USB | 1 |
|
|
| Ethernet | 1 |
|
|
| Vcc | 1.8V - 3.6V |
|
|
| Datasheet | [Datasheet](http://www.st.com/resource/en/datasheet/stm32f207zg.pdf) |
|
|
| Reference Manual | [Reference Manual](http://www.st.com/resource/en/reference_manual/cd00225773.pdf) |
|
|
| Programming Manual | [Programming Manual](http://www.st.com/resource/en/programming_manual/cd00228163.pdf) |
|
|
| Board Manual | [Board Manual](http://www.st.com/resource/en/user_manual/dm00244518.pdf) |
|
|
|
|
## Implementation Status
|
|
|
|
| Device | ID | Supported | Comments |
|
|
|:------------- |:------------- |:------------- |:------------- |
|
|
| MCU | STM32F207ZG | partly | Energy saving modes not fully utilized |
|
|
| Low-level driver | GPIO | yes | |
|
|
| | PWM | yes (7 pins available in see [PR #6192](https://github.com/RIOT-OS/RIOT/pull/6192)) | |
|
|
| | UART | 2 UARTs | USART2 via STLink/USB or D0(RX)/D1(TX) and USART6 on PA12(RX)/PA11(TX) |
|
|
| | I2C | 1 I2C | |
|
|
| | SPI | 1 SPI | |
|
|
| | USB | no | |
|
|
| | Timer | 2 32 bit timers | |
|
|
|
|
## Flashing the device
|
|
|
|
### Flashing the Board Using OpenOCD
|
|
|
|
The ST Nucleo-F207ZG board includes an on-board ST-LINK V2-1 programmer. The
|
|
easiest way to program the board is to use OpenOCD. Once you have installed
|
|
OpenOCD (look [here](https://github.com/RIOT-OS/RIOT/wiki/OpenOCD) for
|
|
installation instructions), you can flash the board simply by typing
|
|
|
|
```
|
|
make BOARD=nucleo-f207zg flash
|
|
```
|
|
and debug via GDB by simply typing
|
|
```
|
|
make BOARD=nucleo-f207zg debug
|
|
```
|
|
|
|
### Flashing the Board Using ST-LINK Removable Media
|
|
|
|
On-board ST-LINK programmer provides via composite USB device removable media.
|
|
Copying the HEX file causes reprogramming of the board. This task
|
|
could be performed manually; however, the cpy2remed (copy to removable
|
|
media) PROGRAMMER script does this automatically. To program board in
|
|
this manner, use the command:
|
|
```
|
|
make BOARD=nucleo-f207zg PROGRAMMER=cpy2remed flash
|
|
```
|
|
@note This PROGRAMMER was tested using ST-LINK firmware 2.37.26. Firmware updates
|
|
could be found on [this STM webpage](https://www.st.com/en/development-tools/stsw-link007.html).
|
|
|
|
## Supported Toolchains
|
|
For using the ST Nucleo-F207ZG board we strongly recommend the usage of the
|
|
[GNU Tools for ARM Embedded Processors](https://launchpad.net/gcc-arm-embedded)
|
|
toolchain.
|
|
*/
|