mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2024-12-29 04:50:03 +01:00
86 lines
3.2 KiB
Plaintext
86 lines
3.2 KiB
Plaintext
/**
|
|
@defgroup boards_nucleo-f303k8 STM32 Nucleo-F303K8
|
|
@ingroup boards_common_nucleo32
|
|
@brief Support for the STM32 Nucleo-F303K8
|
|
|
|
## Overview
|
|
|
|
The Nucleo-F303K8 is a board from ST's Nucleo family supporting a ARM Cortex-M4
|
|
STM32F303K8 microcontroller with 12KiB of RAM and 64KiB of ROM.
|
|
|
|
## Hardware
|
|
|
|
|
|
|
|
|
|
### MCU
|
|
| MCU | STM32F303K8 |
|
|
|:---------- |:--------------------- |
|
|
| Family | ARM Cortex-M4 |
|
|
| Vendor | ST Microelectronics |
|
|
| RAM | 12KiB |
|
|
| Flash | 64KiB |
|
|
| Frequency | up to 72MHz |
|
|
| FPU | yes |
|
|
| Timers | 8 (4x 16-bit, 1x 32-bit [TIM2], 2x watchdog, 1x Systick) |
|
|
| ADCs | 2x 12-bit (9 channels) |
|
|
| UARTs | 2 |
|
|
| SPIs | 1 |
|
|
| I2Cs | 1 |
|
|
| RTC | 1 |
|
|
| Vcc | 2.0V - 3.6V |
|
|
| Datasheet | [Datasheet](https://www.st.com/resource/en/datasheet/stm32f303k8.pdf) |
|
|
| Reference Manual | [Reference Manual](https://www.st.com/resource/en/reference_manual/dm00043574.pdf) |
|
|
| Programming Manual | [Programming Manual](http://www.st.com/web/en/resource/technical/document/programming_manual/DM00046982.pdf) |
|
|
| Board Manual | [Board Manual](https://www.st.com/resource/en/user_manual/dm00231744.pdf)|
|
|
|
|
|
|
|
|
## Implementation Status
|
|
| Device | ID | Supported | Comments |
|
|
|:------------- |:------------- |:------------- |:------------- |
|
|
| MCU | STM32F303K8 | partly | Energy saving modes not fully utilized |
|
|
| Low-level driver | GPIO | yes | |
|
|
| | PWM | one PWM | |
|
|
| | UART | three UART | |
|
|
| | I2C | two I2C | |
|
|
| | SPI | two SPI | |
|
|
| | USB | no | |
|
|
| | Timer | one 32 timer | |
|
|
|
|
|
|
## Flashing the device
|
|
|
|
### Flashing the Board Using OpenOCD
|
|
|
|
The ST Nucleo-F303K8 board includes an on-board ST-LINK V2 programmer.
|
|
The easiest way to program the board is to use OpenOCD. Once you have
|
|
installed OpenOCD (look [here](https://github.com/RIOT-OS/RIOT/wiki/OpenOCD)
|
|
for installation instructions), you can flash the board simply by typing.
|
|
|
|
```
|
|
BOARD=nucleo-f303k8 make flash
|
|
```
|
|
and debug via GDB by simply typing
|
|
```
|
|
BOARD=nucleo-f303k8 make debug
|
|
```
|
|
### Flashing the Board Using ST-LINK Removable Media
|
|
|
|
On-board ST-LINK programmer provides via composite USB device removable media.
|
|
Copying the HEX file causes reprogramming of the board. This task
|
|
could be performed manually; however, the cpy2remed (copy to removable
|
|
media) PROGRAMMER script does this automatically. To program board in
|
|
this manner, use the command:
|
|
```
|
|
make BOARD=nucleo-f303k8 PROGRAMMER=cpy2remed flash
|
|
```
|
|
@note This PROGRAMMER was tested using ST-LINK firmware 2.37.26. Firmware updates
|
|
can be found on [this STM webpage](https://www.st.com/en/development-tools/stsw-link007.html).
|
|
|
|
## Supported Toolchains
|
|
For using the ST Nucleo-F303K8 board we strongly recommend the usage of the
|
|
[GNU Tools for ARM Embedded Processors](https://launchpad.net/gcc-arm-embedded)
|
|
toolchain.
|
|
*/
|