/**
@defgroup    boards_nucleo-f070rb STM32 Nucleo-F070RB
@ingroup     boards_common_nucleo64
@brief       Support for the STM32 Nucleo-F070RB

## Overview

The Nucleo-F070RB is a board from ST's Nucleo family supporting a ARM Cortex-M0
STM32F070RB microcontroller with 16Kb of SRAM and 128Kb of ROM Flash.

## Hardware

![Nucleo64 F070RB]
(http://www.open-electronics.org/wp-content/uploads/2015/08/Figura2-500x467.png)



### MCU
| MCU                   | STM32F070RB                                                                           |
|:--------------------- |:------------------------------------------------------------------------------------- |
| Family                | ARM Cortex-M0                                                                         |
| Vendor                | ST Microelectronics                                                                   |
| RAM                   | 16KiB                                                                                 |
| Flash                 | 128KiB                                                                                |
| Frequency             | up to 48MHz                                                                           |
| FPU                   | no                                                                                    |
| Timers                | 11 (2x watchdog, 1 SysTick, 8x 16-bit)                                                |
| ADCs                  | 1x 12-bit (16 channels)                                                               |
| UARTs                 | 4                                                                                     |
| SPIs                  | 2                                                                                     |
| I2Cs                  | 2                                                                                     |
| RTC                   | 1                                                                                     |
| USB                   | 1                                                                                     |
| Vcc                   | 2.4V - 3.6V                                                                           |
| Datasheet             | [Datasheet](http://www.st.com/resource/en/datasheet/stm32f070rb.pdf)                  |
| Reference Manual      | [Reference Manual](https://www.st.com/resource/en/reference_manual/dm00091010.pdf)    |
| Programming Manual    | [Programming Manual](http://www.st.com/resource/en/programming_manual/dm00051352.pdf) |
| Board Manual          | [Board Manual](http://www.st.com/resource/en/user_manual/dm00105823.pdf)              |



## Implementation Status
| Device | ID        | Supported | Comments  |
|:------------- |:------------- |:------------- |:------------- |
| MCU        | STM32F070RB   | partly    | Energy saving modes not fully utilized |
| Low-level driver | GPIO    | yes       | |
|        | PWM       | yes (4 pins available)    |  |
|        | UART      | 3 UARTs       | USART2 via STLink/USB or D0(RX)/D1(TX), USART1 on PA10(RX)/PA09(TX) and USART3 on PC11(RX)/PC10(TX) |
|        | ADC       | 6 pins        | |
|        | I2C       | no        | |
|        | SPI       | no        | |
|        | USB       | no        | |
|        | Timer     | 3 16 bit timers       | |


## Flashing the device
The ST Nucleo-F070RB board includes an on-board ST-LINK V2 programmer. The
easiest way to program the board is to use OpenOCD. Once you have installed
OpenOCD (look [here](https://github.com/RIOT-OS/RIOT/wiki/OpenOCD) for
installation instructions), you can flash the board simply by typing

```
make BOARD=nucleo-f070rb flash
```
and debug via GDB by simply typing
```
make BOARD=nucleo-f070rb debug
```


## Supported Toolchains
For using the ST Nucleo-F070RB board we strongly recommend the usage of the
[GNU Tools for ARM Embedded Processors](https://launchpad.net/gcc-arm-embedded)
toolchain.
 */