/**
@defgroup    boards_pic32-wifire Digilent PIC32 WiFire
@ingroup     boards
@brief       Support for the Digilent PIC32 WiFire
@deprecated  Will not be available after the 2022.07 release. This includes
             all MIPS based boards and cpus.

## Overview

The ChipKit Wifire is a development board by Digilent featuring a PIC32MZ and a Wifi module (MRF24WG0MA).
General information about the board can be found [here](https://store.digilentinc.com/wi-fire-wifi-enabled-pic32mz-microcontroller-board/)
Please do not use board rev A or B as they use a different MCU (PIC32MZ2048ECG100).

Additional documents:
  * [Schematics](https://reference.digilentinc.com/_media/reference/microprocessor/wi-fire/chipkit_wifire_sch.pdf) for the Wifire board rev C
  * [Schematics](https://reference.digilentinc.com/_media/reference/microprocessor/wi-fire/wifire_sch.pdf) for the Wifire board rev D
  * [Reference manual](https://reference.digilentinc.com/_media/reference/microprocessor/wi-fire/wi-fire_rm_revd.pdf) for the Wifire board rev D

## Hardware

### MCU

| MCU        | PIC32MZ2048EFG100    |
|:---------- |:-------------------- |
| Family     | PIC32MZ (MIPS M5150) |
| Vendor     | Microchip            |
| RAM        | 512Kb                |
| Flash      | 2048Kb               |
| Frequency  | 200MHz               |
| FPU        | yes                  |
| Timers     | 9 (all 16-bit)       |
| ADCs       | 1x 40-channel 12-bit |
| USB 2.0    | 1                    |
| UARTs      | 6                    |
| SPIs       | 6                    |
| I2Cs       | 5                    |
| RTC        | yes                  |
| RNG        | yes                  |
| Vcc        | 2.1V - 3.6V          |
| Datasheet  | [Datasheet](http://ww1.microchip.com/downloads/en/DeviceDoc/PIC32MZ%20EF%20Family%20Datasheet_DS60001320G.pdf) |


### User Interface

3 Buttons:

| NAME   | Reset  |  T1 |  T2 |
|:-----  |:------ |:--- |:--- |
| Pin    | nReset | RA5 | RA4 |

4 LEDs:

| NAME  | LD1   | LD2   | LD3   | LD4   |
| ----- | ----- | ----- | ----- | ----- |
| Color | green | green | green | green |
| Pin   | RG6   | RD4   | RB11  | RG15  |

## Implementation Status

| Device           | ID                | Supported | Comments               |
|:---------------- |:---------------   |:--------- |:---------------------- |
| MCU              | pic32mz2048efg100 | partly    |                        |
| Low-level driver | GPIO              | partly    | gpio_irq not supported |
|                  | ADC               | no        |                        |
|                  | PWM               | no        |                        |
|                  | UART              | yes       |                        |
|                  | I2C               | no        |                        |
|                  | SPI               | no        |                        |
|                  | USB               | no        |                        |
|                  | RTT               | no        |                        |
|                  | RTC               | no        |                        |
|                  | RNG               | yes       |                        |
|                  | Timer             | no        |                        |

## Using UART

This board opens a serial interface through the USB automatically.

## Flashing the device

There are three ways to flash the MCU:
  * Using MPLAB-IPE and a PICkit 3 (The RIOT build generates a hexfile
    compatible with MPLAB-IPE)
  * Using pic32prog and a PICkit 2 or a PICkit 3 (other devices might be
    supported by pic32prog but were not tested).
  * Using a SEGGER J-Link probe. JTAG pins are available on the JP3 connector.

## Supported Toolchains

For using the pic32-wifire board we strongly recommend the usage of the
[Codescape GNU Tools](https://codescape.mips.com) toolchain.

 */