# Copyright (c) 2020 Freie Universitaet Berlin # # This file is subject to the terms and conditions of the GNU Lesser # General Public License v2.1. See the file LICENSE in the top level # directory for more details. # menuconfig KCONFIG_USEMODULE_AT86RF215 bool "Configure AT86RF215 driver" depends on USEMODULE_AT86RF215 help Configure the AT86RF215 driver using Kconfig. if KCONFIG_USEMODULE_AT86RF215 config AT86RF215_USE_CLOCK_OUTPUT bool "Enable clock output" help Enable this to enable the clock output pin of the AT86RF215 chip. This way it can be used as a clock source in place of a separate crystal. You also have to enable this if you want to measure the clock frequency for trimming. After proper trim value is applied this may be disabled if not used otherwise. By Default it is turned off to save energy. config AT86RF215_TRIM_VAL_EN bool "Enable crystal oscillator trimming" help Enable crystal oscillator trimming. config AT86RF215_RPC_EN bool "Enable Reduced Power Consumption" help Reduce Power Consumption in RX IDLE by duty-cycling the RF circuitry. config AT86RF215_TRIM_VAL int "Trim value for the crystal oscillator" range 0 15 default 0 depends on AT86RF215_TRIM_VAL_EN help Each increment adds 300nF capacitance between the crystal oscillator pins TCXO and XTAL2.Tweak the value until the measured clock output matches 26 MHz the best. For more information Refer Table 6-25 TRIM in Datasheet config AT86RF215_RESET_PULSE_WIDTH_US int "Width of the reset pulse (µs)" range 16 1000 default 16 help If your board design includes a filtering capacitor on the reset line, this raises the rise time of the reset pulse. To accommodate for this, select a larger reset pulse width here. If unsure, leave this at the default value of 16 µs. choice prompt "Default Modulation" config AT86RF215_DEFAULT_LEGACY_OQPSK bool "legacy O-QPSK" help O-QPSK compatible with IEEE 802.15.4-2003 devices config AT86RF215_DEFAULT_MR_OQPSK bool "MR-O-QPSK" help MR-O-QPSK according to IEEE 802.15.4g config AT86RF215_DEFAULT_MR_OFDM bool "MR-OFDM" help MR-O-OFDM according to IEEE 802.15.4g endchoice menu "O-QPSK (802.15.4) configuration" depends on AT86RF215_DEFAULT_LEGACY_OQPSK config AT86RF215_DEFAULT_OQPSK_RATE int "Default (legacy) O-QPSK rate mode" range 0 1 default 0 help The at86rf215 supports proprietary high data rates that are compatible with the at86rf2xx parts. Set this to 1 to configure the proprietary high-data rate option as default. If unsure, leave this at 0. endmenu # legacy O-QPSK menu "MR-O-QPSK (802.15.4g) configuration" depends on AT86RF215_DEFAULT_MR_OQPSK config AT86RF215_DEFAULT_MR_OQPSK_RATE int "Default MR-O-QPSK rate mode" range 0 3 default 2 help Default Rate Mode of the MR-O-QPSK PHY Each increment doubles the PSDU data rate. choice prompt "Default MR-O-QPSK Chip Rate" config AT86RF215_DEFAULT_MR_OQPSK_CHIPS_100 bool "100 kchip/s" config AT86RF215_DEFAULT_MR_OQPSK_CHIPS_200 bool "200 kchip/s" config AT86RF215_DEFAULT_MR_OQPSK_CHIPS_1000 bool "1000 kchip/s" config AT86RF215_DEFAULT_MR_OQPSK_CHIPS_2000 bool "2000 kchip/s" endchoice endmenu # MR-O-QPSK menu "MR-OFDM (802.15.4g) configuration" depends on AT86RF215_DEFAULT_MR_OFDM config AT86RF215_DEFAULT_MR_OFDM_OPT int "Default MR-OFDM option" range 1 4 default 2 help Default Option of the MR-OFDM PHY Each increment halves the PSDU data rate. config AT86RF215_DEFAULT_MR_OFDM_MCS int "Default MR-OFDM Modulation & Coding Scheme" range 0 6 default 2 help Default Modulation & Coding Scheme of the MR-OFDM PHY. Higher schemes correspond to higher data rates and lower range. 0: BPSK, rate 1⁄2, 4 x frequency repetition 1: BPSK, rate 1⁄2, 2 x frequency repetition 2: QPSK, rate 1⁄2, 2 x frequency repetition 3: QPSK, rate 1⁄2 4: QPSK, rate 3⁄4 5: 16-QAM, rate 1⁄2 6: 16-QAM, rate 3⁄4 endmenu endif # KCONFIG_USEMODULE_AT86RF215